AVSPARE.COM
parts catalog

TUBE AS 2444135 - Caterpillar


2444135 TUBE AS Caterpillar parts 345C, 345C L
Rating:
19
Alternative (cross code) number:
CA2444135
244-4135
2444135
Caterpillar 2444135 TUBE AS
Weight: 0.37 pounds 0 kg.

Buy TUBE AS 2444135 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 2444135:

EXCAVATOR  345C   345C L   Caterpillar
Number on catalog scheme: 4
 
  For full view, you need register

Information:

Installation Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     277-5832     Wrench     1    Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 1 g01178239
Use a suitable lifting device to position implement piston pump (6) . The weight of implement piston pump (6) is approximately 95 kg (210 lb).
Use Tooling (A) to install bolts (7) .
Illustration 2 g01178237
Connect elbows (4) and (5) .
Connect ball valve (2) .
Connect hose assemblies (1) and (3) .
Illustration 3 g01873213
Illustration 4 g01873215
To avoid system damage, make sure that the hydraulic pump is properly filled with hydraulic oil before start-up.
In order to fill the case of the implement pump, the steering pump, and the fan pumps, fully open the fill valve that is located between the hydraulic tank and the implement pump. Refer to illustration 3.
Attach a purge line to the pressure tap that is located in the case drain line above the fan pump. Refer to illustration 4.
Begin filling the hydraulic tank with oil. Once oil begins to flow out of the purge line, remove the purge line and fully close the fill valve.
Continue to fill the hydraulic tank to the correct level. Refer to Operation and Maintenance Manual, "Hydraulic System Oil - Change".Note: During initial start-up, the engine should never run higher than low idle until the hydraulic system has been cycled and the hydraulic tank oil level has been readjusted to the correct level.End By: Install the steering pump. Refer to Disassembly and Assembly, "Piston Pump (Steering) - Install".

Caterpillar parts catalog:

Caterpillar parts catalog
345C L Hydraulic Excavator ESD00001-UP (MACHINE) POWERED BY C13 Engine
345C LC Excavator DHP00001-UP (MACHINE) POWERED BY C13 Engine
345C & 345C L Excavators BWY00001-UP (MACHINE) POWERED BY C13 Engine
345C Excavator TAJ00001-UP (MACHINE) POWERED BY C13 Engine
345C L Excavator S5M00001-UP (MACHINE) POWERED BY C13 Engine


Parts tube Caterpillar catalog:

2767222 TUBE AS-OIL JET
14M, 16M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 725, 730, 730C, 966H, 972H,...
2378526 TUBE
305.5, 306, 306E, 307B, 307C, 307D, 308C, 311C, 312C, 312C L, 314C, 315C, 318C, 319C, 320B, 320C, 320C FM, 321C, 322B L, 322C, 325C, 330B L, 330C, 330C L, 330C MH, 345B II, 345B II MH, 345C, 345C L, 3...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.