AVSPARE.COM
parts catalog

TUBE AS 2915624 - Caterpillar


2915624 TUBE AS Caterpillar parts 854K, 992K
Rating:
59
Alternative (cross code) number:
CA2915624
291-5624
2915624
Caterpillar 2915624 TUBE AS
Weight: 9 pounds 4 kg.

Buy TUBE AS 2915624 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL DOZER, WHEEL LOADER,

Compatible equipment models: 2915624:

WHEEL DOZER  854K  
WHEEL LOADER  992K   Caterpillar
Number on catalog scheme: 26
  For full view, you need register

Information:


Illustration 3 g03795592
(A) 270.0 2.0 mm (10.63 0.08 inch)
(B) 40.0 2.0 mm (1.57 0.08 inch) Place film (4) in lift bracket assembly (2) as per the dimensions shown in Illustration 3.Installation Procedure
Illustration 4 g03795593
Place lift bracket assembly (2) on top of cab and line up with existing holes. The existing M12 clearance hole in the rear of the cab should be lined up with the rear hole of the lift. The two existing M16 clearance holes in the front of the cab should be lined up with the front holes of the lift. Refer to Illustration 4 for the correct orientation and hole lineup. Lift bracket assembly (2) should be placed on the Skid Steer Loader in orientation as shown in Illustration 4 so that the holes will line up as shown.
Illustration 5 g03795595
Ensure that lift bracket assembly is properly fitted and place both shim (7) and plate (8) between side sheet of cab and side plate of lift bracket assembly to obtain a snug fit at each hole location. Refer to Illustration 5 for proper shim location. A tight joint should be obtained between the side sheet of the cab and plate (8).Note: Install shims (7) as required in order to ensure a tight bolted joint at each hole location and no gap is visible between cab side sheet and side plate of lift.
Install M16 flat head screws (5) and M12 flat head screws (6) and hand tighten. Refer to Illustration 5.
Illustration 6 g03795596
Mark the center of the front M12 hole at the rear of the lift on the left side as shown in Illustration 6. The mark should be placed on the side sheet of the cab. After marking, drill a 14 mm (0.6 inch) hole with the center of the bit placed at the mark on the side sheet of the cab. Note: The 14 mm (0.6 inch) clearance hole may require the use of a pilot hole.
Ensure that the nut and screw surfaces are clean.
Apply blue Loctite 243 to the threads of 160-0018 Flat Head Screw (6) that will be engaged with 6V-8149 Nut (1).
Install 160-0018 Flat Head Screw (6) in newly drilled hole and hand tighten.
Remove 159-2953 Flat Head Screw (5) in front and M12 hole from far rear and apply blue Loctite 243 to the threads.
Install 159-2953 Flat Head Screw and 160-0018 Flat Head Screw. Hand tighten the screws.
Tighten all 159-2953 Flat Head Screws to 240 40 N m (177 30 lb ft) and all 6V-8149 Nuts to 100 20 N m (74 15 lb ft).
Repeat Step 4 through Step 10 for the right side of the lift bracket assembly.
Allow blue Loctite 243 to cure for at least 24 hours.
Ensure that all hardware is secure and the lift bracket assembly is shimmed properly before to first use. Additional Information
Restrictions:
Do NOT exceed a lifting weight of 6100 kg (13448 lb)
Do NOT lift with any work tools attached
Machine can only be lifted with lift arms in the furthest downward position
Refer

Caterpillar parts catalog:

Caterpillar parts catalog
854K Wheel Dozer RM300001-UP (MACHINE) POWERED BY C32 Engine
854K Wheel Dozer KK300001-UP (MACHINE) POWERED BY C32 Engine
992K Wheel Loader RM200001-UP (MACHINE) POWERED BY C32 Engine
992K Wheel Loader KK200001-UP (MACHINE) POWERED BY C32 Engine
992K Wheel Loader KK400001-UP (MACHINE) POWERED BY C32 Engine
992K Wheel Loader RM500001-UP (MACHINE) POWERED BY C32 Engine
854K Wheel Dozer KK600001-UP (MACHINE) POWERED BY C32 Engine
854K Wheel Dozer RM600001-UP (MACHINE) POWERED BY C32 Engine
992K Wheel Loader H4C00001-UP (MACHINE) POWERED BY C32 Engine
854K Wheel Dozer 22100001-UP (MACHINE) POWERED BY C32 Engine
854K Wheel Dozer H8M00001-UP (MACHINE) POWERED BY C32 Engine
992K Wheel Loader 88000001-UP (MACHINE) POWERED BY C32 Engine
854K Wheel Dozer H9K00001-UP (MACHINE) POWERED BY C32 Engine
992K Wheel Loader ZMX00001-UP (MACHINE) POWERED BY C32 Engine


Parts tube Caterpillar catalog:

3556043 TUBE AS-OIL JET
777C, 777D, 777F, 777G, 854K, 992K, 993K, C27, C32, D11R, D11T
4N1849 TUBE-AIR
3408C, 3412, 3412C, 3412E, 3512, 631D, 637D, 639D, 69D, 768C, 769C, 769D, 771C, 771D, 772B, 773B, 773G, 773G OEM, 775B, 775G, 775G OEM, 777G, 834B, 836, 844K, 854K, 988B, 990, 990K, 992C, 992D, 992K, ...
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.