2967192 TUBE AS Caterpillar parts
311D LRR
Rating:
Alternative (cross code) number:
CA2967192
296-7192
2967192
CA2967192
296-7192
2967192
Weight: 4 pounds 1 kg.
EXCAVATOR,
Compatible equipment models: 2967192:
Number on catalog scheme:
14
For full view, you need register
Information:
Parts Needed
Dealers will need to order parts for this Program.
1 - 9X9511 Solenoid1 - 4H7869 Gasket**On the 3406E, the gasket you remove may be a different part number. The 155-8725 Gasket is used only to prevent the initial E-Coat from bleeding into the housing / starter joint. The 4H7869 is completely satisfactory for the 3406E after E-Coat.Action Required
This Program will replace the solenoid on engines having a 24V (6V5539 or 3T2610) starters. In most cases, only the solenoid should be replaced without removing rhe starter from the engine. If the starter must be removed to change the solenoid, then new seed stock Starters will be used for initial replacements. Only Dealer Branches with population of these engines should order starters. Orders will be limited to two starters per Branch. Bring the replaced starters back to the shop for solenoid replacement and use for the next engine to be updated. Stamp a "CS" in the lower right corner of the border after starter has been reworked.
Parts Stock
Replace the Solenoid on all 6V5539 and 3T2650 Starters in Dealer Stock which have a Date Code which indicates a starter built prior to Jul 28, 1998 (98G28). The Date Code is located in the left lower portion of the border that encircles the name plate on the starter. The first two numbers represent the year. The Letter represents the month in alphabetic succession without using "i" and the next two numbers, the day of the month. See Illustration Below for example.
For Reman Starter Motors, use the following information for identification.
Replace the Solenoid on all 0R4259 Starters in Dealer Stock which do not have a date code of NRDD, NADD, NLDD, NKDD, NODD, OR NDDD.
Affected Product
See the attached Rework Procedure.
Owner Notification
U.S. and Canadian owners will receive the attached Owner Notification.
Service Claim Allowances
Parts Disposition
Handle the removed solenoids in accordance with your Warranty Bulletin on warranty parts handling.
MAKE EVERY EFFORT TO COMPLETE THIS PROGRAM AS SOON AS POSSIBLE.
Attach.(1-Owner Notification)(1-Rework Procedure)(1-Starter Model Comparison)Copy Of Owner Notification For U.S. And Canadian Owners
Rework Procedure
1. Inspect the starter motor to determine if it is the 24V 42MT (6V5539 or 3T2650) that needs to be reworked.2. Remove the old solenoid and install a new 9X9511 Solenoid. 3. If the solenoid is inaccesable on the engine, remove the starter per the instructions in the Disassembly and Assembly section of the Service Manual. Check and adjust the pinion clearance per the following procedure. A. Disconnect the negative terminal wire from the ground (G) terminal of the solenoid.B. Connect two 12 V batteries to the starting motor as shown. Connect one jumper cable from the battery negative (-) post to the solenoid ground (G) terminal. Connect another jumper cable from the battery positive post to the solenoid start (S) terminal.C. Momentarily flash a third jumper lead from the solenoid ground (G) terminal to the motor (Mtr) terminal. The pinion drive will now shift into the cranking position and remain there until the batteries are disconnected.D. Push the pinion back
Dealers will need to order parts for this Program.
1 - 9X9511 Solenoid1 - 4H7869 Gasket**On the 3406E, the gasket you remove may be a different part number. The 155-8725 Gasket is used only to prevent the initial E-Coat from bleeding into the housing / starter joint. The 4H7869 is completely satisfactory for the 3406E after E-Coat.Action Required
This Program will replace the solenoid on engines having a 24V (6V5539 or 3T2610) starters. In most cases, only the solenoid should be replaced without removing rhe starter from the engine. If the starter must be removed to change the solenoid, then new seed stock Starters will be used for initial replacements. Only Dealer Branches with population of these engines should order starters. Orders will be limited to two starters per Branch. Bring the replaced starters back to the shop for solenoid replacement and use for the next engine to be updated. Stamp a "CS" in the lower right corner of the border after starter has been reworked.
Parts Stock
Replace the Solenoid on all 6V5539 and 3T2650 Starters in Dealer Stock which have a Date Code which indicates a starter built prior to Jul 28, 1998 (98G28). The Date Code is located in the left lower portion of the border that encircles the name plate on the starter. The first two numbers represent the year. The Letter represents the month in alphabetic succession without using "i" and the next two numbers, the day of the month. See Illustration Below for example.
For Reman Starter Motors, use the following information for identification.
Replace the Solenoid on all 0R4259 Starters in Dealer Stock which do not have a date code of NRDD, NADD, NLDD, NKDD, NODD, OR NDDD.
Affected Product
See the attached Rework Procedure.
Owner Notification
U.S. and Canadian owners will receive the attached Owner Notification.
Service Claim Allowances
Parts Disposition
Handle the removed solenoids in accordance with your Warranty Bulletin on warranty parts handling.
MAKE EVERY EFFORT TO COMPLETE THIS PROGRAM AS SOON AS POSSIBLE.
Attach.(1-Owner Notification)(1-Rework Procedure)(1-Starter Model Comparison)Copy Of Owner Notification For U.S. And Canadian Owners
Rework Procedure
1. Inspect the starter motor to determine if it is the 24V 42MT (6V5539 or 3T2650) that needs to be reworked.2. Remove the old solenoid and install a new 9X9511 Solenoid. 3. If the solenoid is inaccesable on the engine, remove the starter per the instructions in the Disassembly and Assembly section of the Service Manual. Check and adjust the pinion clearance per the following procedure. A. Disconnect the negative terminal wire from the ground (G) terminal of the solenoid.B. Connect two 12 V batteries to the starting motor as shown. Connect one jumper cable from the battery negative (-) post to the solenoid ground (G) terminal. Connect another jumper cable from the battery positive post to the solenoid start (S) terminal.C. Momentarily flash a third jumper lead from the solenoid ground (G) terminal to the motor (Mtr) terminal. The pinion drive will now shift into the cranking position and remain there until the batteries are disconnected.D. Push the pinion back
Caterpillar parts catalog:
Parts tube Caterpillar catalog:
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
10-20B, 1090, 1190, 1190T, 120K, 120K 2, 120M, 120M 2, 1290T, 12H, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 1390, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 160K, 160M 2, 160M 3, 160M 3 AWD, 216, 216B,...
311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D F...
2290964
TUBE AS
311C, 311D LRR
311C, 311D LRR
311D LRR, 312D, 312D L, 313D, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321C,...
2887692
TUBE AS
311D LRR, 311F LRR, 312D, 312D L, 312D2, 314D CR, 314D LCR
311D LRR, 311F LRR, 312D, 312D L, 312D2, 314D CR, 314D LCR
2887699
TUBE AS
311D LRR, 311F LRR, 312D, 312D L, 312D2, 312E, 312E L, 314D CR, 314D LCR
311D LRR, 311F LRR, 312D, 312D L, 312D2, 312E, 312E L, 314D CR, 314D LCR
3465590
TUBE AS
311D LRR, 312D, 312D L, 312D2, 312E, 312E L, 314D CR, 314D LCR, 314E LCR, PIN GRAB
311D LRR, 312D, 312D L, 312D2, 312E, 312E L, 314D CR, 314D LCR, 314E LCR, PIN GRAB
2852776
TUBE AS
311D LRR, 311F LRR
311D LRR, 311F LRR
3937916
TUBE AS
311D LRR, 311F LRR
311D LRR, 311F LRR
3852955
TUBE AS
311D LRR, 311F LRR
311D LRR, 311F LRR
2866536
TUBE AS
311D LRR
311D LRR
2967001
TUBE AS
311D LRR
311D LRR
2967000
TUBE AS
311D LRR
311D LRR
3029190
TUBE AS
311D LRR, 314D LCR
311D LRR, 314D LCR
3029189
TUBE AS
311D LRR, 314D LCR
311D LRR, 314D LCR
3029188
TUBE AS
311D LRR, 314D LCR
311D LRR, 314D LCR
3029187
TUBE AS
311D LRR, 314D LCR
311D LRR, 314D LCR
2946356
TUBE AS
311D LRR, 314D LCR, 325D L
311D LRR, 314D LCR, 325D L
3029528
TUBE AS
311D LRR, 314D LCR
311D LRR, 314D LCR
3029527
TUBE AS
311D LRR, 314D LCR
311D LRR, 314D LCR
3598865
TUBE AS
311D LRR
311D LRR
3598862
TUBE AS
311D LRR
311D LRR
2967193
TUBE AS
311D LRR
311D LRR