AVSPARE.COM
parts catalog

TUBE A 7F2986 2H9093 - Caterpillar



2H9093 TUBE A 7F2986 Caterpillar parts TUBE
Rating:
21
Alternative (cross code) number:
CA2H9093
2H-9093
2H9093
Caterpillar 2H9093 TUBE A 7F2986

Buy TUBE A 7F2986 2H9093 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:

GPS
The "Machine Radio Configuration" utility allows you to change the network number or the frequency channel on a data radio. The "Machine Radio Configuration" utility runs on the AccuGrade display.Note: You can only configure radios that have firmware version 1.4 or greater with this utility. IP radios cannot be configured with this utility.Using the "Machine Radio Configuration" Utility
Start the display in "Service Mode".
From the "Setup Menu – Configuration" screen, press the "Installation" soft key in order to list the items under the "Setup Menu – Installation" screen.
Press the up arrow or the down arrow until "Machine Radio Configuration" is highlighted.
Illustration 1 g01383211
Press the "OK" key. A screen that is similar to Illustration 2 will appear.
Illustration 2 g01360780
Enter the "Network" number. Press "OK" in order to have the display accept the "Network" number. After the "OK" button is pressed, the display will automatically return to the previous screen, Illustration 1.
Press the "Escape" button, that is on the display, in order to exit the "Setup Menu - Configuration" menu. TC900C, CR900 Data Radios
If the AccuGrade system detects a TC900C radio or a CR900, the screen in Illustration 3 will appear.The network number that is shown defaults to "Unknown".
Illustration 3 g01360826
Use the down arrow key and the up arrow key in order to select the required network channel (Network 1–40).
Press the "OK" key in order to save the radio network changes and power down the display, or press the "ESC" key in order to cancel the changes.Note: The radio must have the same network number as the base station radio that you want to receive GPS corrections. TC450C Data Radio
If the AccuGrade system detects a TC450C radio, the screen shown in Illustration 4 appears.
Illustration 4 g01360826
Note: The TC450C has a selection of up to twenty preset frequency channels.Note: The current radio frequency channel is displayed on start up.
Use the down arrow key and the up arrow key in order to select the channel that is desired.
Press the "OK" key in order to save the radio frequency channel and power down the display, or press the "ESC" key in order to cancel the changes.Note: The radio must have the same frequency channel as the base station radio that you want to receive GPS corrections. In most areas, licensing is required for 450 Mhz frequencies. Be sure the frequency that is selected is licensed with the customer. "Display's Radio Port"
When a third party radio is used, the Display for the AccuGrade System allows the user to adjust the following communication parameters:
Baud Rate
ParityThe "Display's Radio Port" settings sets the speed at which the Display communicates with the radio. These settings do not affect the speed of data transfer though the air between radios. Refer to the following Steps in order to adjust the "Display's Radio Port" settings.
Illustration 5 g01265962
(1) LCD (2) Soft Key Labels (3) Soft Keys (4) Escape Key (5 ) Next Key (6) Power Key (7) "+" Key (8) Arrow Keys (9) "-" Key (10) "OK" Key (11) Menu Key (12) "Data Card Slot"
To view all options


Parts tube Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.