AVSPARE.COM
parts catalog

TUBE 2H9677 - Caterpillar



2H9677 TUBE Caterpillar parts TUBE
Rating:
86
Alternative (cross code) number:
CA2H9677
2H-9677
2H9677
Caterpillar 2H9677 TUBE
Weight: 279 pounds 126 kg.

Buy TUBE 2H9677 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01273487
Right Joystick Position Sensor CircuitThis diagnostic is associated with the Left/Right Position Sensor of the Right Joystick base. The sensor provides an input signal to the ECM. The diagnostic code is recorded when the ECM has determined that the signal frequency or the signal pulse width is not within the expected range.The sensor is a PWM sensor that operates at a frequency of 500 80 Hz. The duty cycle of the signal will vary from approximately 20% at the joystick full rearward position to approximately 80% at the joystick full forward position. When the joystick is in the center position, the duty cycle will be approximately 50%. The possible causes of this diagnostic code are listed below:
The sensor has failed.
Intermittent connections or poor connections
The ECM has failed. This is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the problem has been corrected. Verify that CID 2477 - FMI 08 is active before performing this procedure.Test Step 1. CHECK THE SENSOR POWER SUPPLY
Turn the key switch to the ON position.
At the harness connector for the right joystick, insert 7X-1710 Multimeter Probes along the contact for the power supply 1 wire 127-ORand along ground contact 2 wire 203-BK. Do not disconnect the machine harness from the connector for the joystick.
Measure the (12 VDC) battery voltage of the sensor power supply. The key start switch remains in the ON position.Expected Result:The (12 VDC) battery voltage measurement is available.Results:
OK - The (12 VDC) battery measurement is correct. Proceed to Test Step 2.
NOT OK - The measurement is not correct.Repair: Repair or replace the harness.STOPTest Step 2. CHECK THE SIGNAL CIRCUIT FOR A SHORT
Disconnect the negative battery cable and turn the key start switch to the OFF position.
Disconnect machine harness connectors J1 and J2 from the Machine ECM.
At the J2 harness connector for the machine ECM, measure the resistance from the sensor signal contact J2-51 E850-BR). to all other J1 and J2 contacts that are used for the machine ECM.Expected Result:Each resistance measurement is greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The signal circuit is not shorted. Proceed to Test Step 3.
NOT OK - A resistance measurement is less than 5000 ohms.Repair: There is a short in the machine harness. The short is between the signal circuit and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK THE STATUS OF THE DIAGNOSTIC CODE
Inspect the harness connectors and clean the contacts of the harness connectors and check the


Parts tube Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.