TUBE AS 3116297 - Caterpillar

3116297 TUBE AS Caterpillar parts 345C

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA3116297
311-6297
3116297

Buy TUBE AS 3116297 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 3116297:

EXCAVATOR 345C Caterpillar

Number on catalog scheme: 7

Caterpillar 3116297 Parts scheme TUBE AS

For full view, you need register

Information:

Table 2
Tilt Cylinder Drift
Oil Temp. 38 3°C (100 5°F) 49 3°C (120 5°F) 66 3°C (150 5°F) 82 3°C (180 5°F)
Maximum Allowable Drift 8.56 mm (0.337 inch) 13.46 mm (0.530 inch) 24.21 mm (0.953 inch) 38.77 mm (1.526 inch)
Time Interval (minutes) 5.0 5.0 5.0 5.0 Drift Test for Ripper Cylinder
Measure ripper cylinder rod drift by using the following procedure:
Check hydraulic oil temperature.
Lift the ripper to maximum height and move the ripper control lever to the HOLD position. Stop the engine.
Obtain a measurement of the distance of cylinder drift over time. Compare the values to the values in Table 3. Note: The drift distances in Table 3 are for new machines.
Table 3
Ripper Cylinder Drift
Oil Temp. 38 3°C (100 5°F) 49 3°C (120 5°F) 66 3°C (150 5°F) 82 3°C (180 5°F)
Maximum Allowable Drift 3.2 mm (0.126 inch) 4.8 mm (0.189 inch) 9.0 mm (0.354 inch) 15.0 mm (0.591 inch)
Time Interval (minutes) 5.0 5.0 5.0 5.0 Drift Test For Multipurpose Bucket (Cylinder Rod)
Measure cylinder rod drift for the multipurpose bucket by using the following procedure.
Check hydraulic oil temperature.
Activate the tilt circuit. Wait until the bucket reaches the full TILT BACK position.
Move the tilt control lever to the HOLD position.
Move the roller for the multipurpose bucket to the OPEN position. Keep the lever in the OPEN position until there is approximately 609 mm (24.0 inch) between the arm assembly and the bowl assembly. Stop the engine.
Obtain a measurement of the distance of cylinder drift over time. Compare the values to the values in Table 4. Note: The drift distances in Table 4 are for new machines.
Table 4
Drift for Multipurpose Bucket Cylinder
Oil Temp. 38 3°C (100 5°F) 49 3°C (120 5°F) 66 3°C (150 5°F) 82 3°C (180 5°F)
Maximum Allowable Drift 12.0 mm (0.472 inch) 18.0 mm (0.709 inch) 26.0 mm (1.02 inch) 40.0 mm (1.57 inch)
Time Interval (minutes) 5.0 5.0 5.0 5.0 Speed Tests for Cylinders
The oil in the system must be the oil which is recommended in Operation and Maintenance Manual for your machine, and the oil must be at a temperature of 65° 3°C (149° 5°F). All speed tests should be made with the engine speed at HIGH IDLE.Identify the speed of each cylinder. Compare these values to the values in the following tables. Equal values indicate normal circuit operation.If the speed of a cylinder is too slow, check that circuit for cylinder drift.
Table 5
Speed Test of the Lift Cylinders Maximum Speed (seconds)
RAISE (ground level to maximum height) 6.5 0.2
Power LOWER (maximum height to ground level) 3.8 0.2
Float LOWER (maximum height to ground level) 2.7 0.2
Table 6
Speed Test of the Tilt Cylinder Maximum Speed (seconds)
DUMP at maximum height (moving from full TILT BACK to full DUMP)

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

345C HCR Material Handler MTE00001-UP (MACHINE) POWERED BY C13 Engine

255-4333: LINES GP-STICK » SEBP52250395

Parts tube Caterpillar catalog:

2767222 TUBE AS-OIL JET
14M, 16M, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 725, 730, 730C, 966H, 972H,...

2378526 TUBE
305.5, 306, 306E, 307B, 307C, 307D, 308C, 311C, 312C, 312C L, 314C, 315C, 318C, 319C, 320B, 320C, 320C FM, 321C, 322B L, 322C, 325C, 330B L, 330C, 330C L, 330C MH, 345B II, 345B II MH, 345C, 345C L, 3...

1678853 TUBE AS
311D LRR, 312D, 312D L, 314D LCR, 315D L, 319D L, 320D, 323D L, 323D LN, 323D SA, 324D, 324D L, 325D L, 329D L, 330D L, 336D, 336D L, 345C, 345D, 345D L, 365C, 365C L, 385C, 385C L

2302797 TUBE AS
345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, W345C MH

3054765 TUBE
325D L, 345C, 345C L, 345C MH, 345D L, W345C MH

2661052 TUBE AS
345C, 345C L

3023115 TUBE AS
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L

1584021 TUBE AS
345B II, 345B L, 345C, 345C L

1461443 TUBE AS
345B II, 345B L, 345C, 345C L, 345D L

2300237 TUBE AS
345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L

2946501 TUBE AS
345B II, 345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG

2895676 TUBE AS
345C, 345C L, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L

3700274 TUBE AS
325D L, 374D L, 374F L

3700273 TUBE AS
325D L, 374D L, 374F L

3700272 TUBE AS
325D L, 374D L, 374F L