3149980 TUBE Caterpillar parts
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906H, 907H, 908H, C3.4
Rating:
Alternative (cross code) number:
CA3149980
314-9980
3149980
CA3149980
314-9980
3149980
Weight: 0.37 pounds 0 kg.
COMPACT TRACK LOADER, SKID STEER LOADER,
Compatible equipment models: 3149980:
Information:
Refer to the Service Manual for your type of controls. Use the following procedure to start the engine.
DO NOT USE ETHER (starting fluids) unless specifically instructed to do so. If the engine is equipped with an Air Inlet Heater (electrically or fuel ignited manifold heater), DO NOT use ether (starting fluids) at any time. The use could result in engine damage and/or personal injury.
An air inlet heater is installed in the air inlet manifold. The air inlet heater is an electrical device which ignites a controlled amount of fuel in order to provide heated inlet air for cold weather starting.Note: Startability will be improved at temperatures below 16°C (60°F) by the use of the air inlet heater. This will help reduce white smoke and misfire during start-up in cold weather.Startability will be improved at temperatures below −18°C (0°F) from the use of a cylinder block coolant heater or extra battery capacity.When No. 2 diesel fuel is used, the following items provide a means of minimizing starting problems and fuel problems in cold weather: starting aids, engine oil pan heaters, engine coolant heaters, fuel heaters and fuel line insulation.For temperatures below −23°C (−10°F), consult your Caterpillar dealer.
Turn the ignition switch to the RUN position. Advance the throttle in order to supply fuel to the engine. When an air inlet heater is used, advance the throttle in order to supply the maximum fuel to the engine.
Do not engage the starting motor when flywheel is turning. Do not start the engine under load.If the engine fails to start within 30 seconds, release the starter switch or button and wait two minutes to allow the starting motor to cool before attempting to start the engine again.
When an air inlet heater is used, turn the ignition switch to the HEAT position. Maintain the HEAT position for 15 seconds. Turn the ignition switch to the HEAT-START position in order to crank the engine. If the engine fails to start, turn the ignition switch to the HEAT position for 10 seconds. Turn the ignition switch to the HEAT-START position in order to crank the engine. Allow the ignition switch to return to the RUN position as soon as the engine starts.
Oil pressure should rise within 15 seconds after the engine starts. Do not increase engine speed until the oil pressure gauge indicates normal. If oil pressure is not indicated on the gauge within 15 seconds, DO NOT operate the engine. STOP the engine, investigate and correct the cause.
Move the throttle to approximately one quarter of the engine rpm.
Allow the engine to idle for three to five minutes, or allow the engine to idle until the water temperature indicator begins to rise. The engine should run at low idle smoothly until speed is gradually increased to high idle. Allow the white smoke to disperse before proceeding with normal operation. To minimize white smoke for cold weather starting, start the engine and allow the engine to idle for 30 seconds. Increase the rpm until the engine speed
DO NOT USE ETHER (starting fluids) unless specifically instructed to do so. If the engine is equipped with an Air Inlet Heater (electrically or fuel ignited manifold heater), DO NOT use ether (starting fluids) at any time. The use could result in engine damage and/or personal injury.
An air inlet heater is installed in the air inlet manifold. The air inlet heater is an electrical device which ignites a controlled amount of fuel in order to provide heated inlet air for cold weather starting.Note: Startability will be improved at temperatures below 16°C (60°F) by the use of the air inlet heater. This will help reduce white smoke and misfire during start-up in cold weather.Startability will be improved at temperatures below −18°C (0°F) from the use of a cylinder block coolant heater or extra battery capacity.When No. 2 diesel fuel is used, the following items provide a means of minimizing starting problems and fuel problems in cold weather: starting aids, engine oil pan heaters, engine coolant heaters, fuel heaters and fuel line insulation.For temperatures below −23°C (−10°F), consult your Caterpillar dealer.
Turn the ignition switch to the RUN position. Advance the throttle in order to supply fuel to the engine. When an air inlet heater is used, advance the throttle in order to supply the maximum fuel to the engine.
Do not engage the starting motor when flywheel is turning. Do not start the engine under load.If the engine fails to start within 30 seconds, release the starter switch or button and wait two minutes to allow the starting motor to cool before attempting to start the engine again.
When an air inlet heater is used, turn the ignition switch to the HEAT position. Maintain the HEAT position for 15 seconds. Turn the ignition switch to the HEAT-START position in order to crank the engine. If the engine fails to start, turn the ignition switch to the HEAT position for 10 seconds. Turn the ignition switch to the HEAT-START position in order to crank the engine. Allow the ignition switch to return to the RUN position as soon as the engine starts.
Oil pressure should rise within 15 seconds after the engine starts. Do not increase engine speed until the oil pressure gauge indicates normal. If oil pressure is not indicated on the gauge within 15 seconds, DO NOT operate the engine. STOP the engine, investigate and correct the cause.
Move the throttle to approximately one quarter of the engine rpm.
Allow the engine to idle for three to five minutes, or allow the engine to idle until the water temperature indicator begins to rise. The engine should run at low idle smoothly until speed is gradually increased to high idle. Allow the white smoke to disperse before proceeding with normal operation. To minimize white smoke for cold weather starting, start the engine and allow the engine to idle for 30 seconds. Increase the rpm until the engine speed
Caterpillar parts catalog:
Parts tube Caterpillar catalog:
1257874
TUBE-HEAT SHRINK
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
216, 216B, 216B3, 226B, 226B3, 228, 232B, 236, 236B, 236B3, 236D, 242B, 242B3, 242D, 246C, 246D, 247, 247B, 247B3, 248, 252B, 252B3, 256C, 257B, 257B3, 257D, 259B3, 259D, 262C, 262C2, 262D, 267, 267B,...
2934316
TUBE AS
906H, 906H2, 907H, 907H2, 908H, 908H2
906H, 906H2, 907H, 907H2, 908H, 908H2
2992242
TUBE AS
906H, 906H2, 907H, 907H2, 908H, 908H2
906H, 906H2, 907H, 907H2, 908H, 908H2
2918132
TUBE AS
906H, 906H2, 907H, 907H2, 908H, 908H2
906H, 906H2, 907H, 907H2, 908H, 908H2
2918133
TUBE AS
906H, 906H2, 907H, 907H2, 908H, 908H2
906H, 906H2, 907H, 907H2, 908H, 908H2
2947909
TUBE AS
906H, 906H2, 907H, 907H2, 908H, 908H2
906H, 906H2, 907H, 907H2, 908H, 908H2
2768690
TUBE AS
906H, 907H, 908H
906H, 907H, 908H
2775628
TUBE AS
906H, 906H2, 907H, 907H2, 908H, 908H2
906H, 906H2, 907H, 907H2, 908H, 908H2
2840075
TUBE AS
906H, 906H2, 907H, 907H2, 908H, 908H2
906H, 906H2, 907H, 907H2, 908H, 908H2
3273752
TUBE AS
908H, 908H2
908H, 908H2
1658025
TUBE AS
906H, 908H, BP22
906H, 908H, BP22
1561542
TUBE
906H, 908H, 966H, BA30
906H, 908H, 966H, BA30
2583530
TUBE AS
246C, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C
246C, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C
2808327
TUBE
272C, 297C, 299C
272C, 297C, 299C
3355768
TUBE-OIL GAUGE
256C, 262C, 272C, 277C, 279C, 287C, 289C, 297C, 299C
256C, 262C, 272C, 277C, 279C, 287C, 289C, 297C, 299C
2291454
TUBE AS
428E
428E
2291451
TUBE AS
428E
428E
2291449
TUBE AS
428E
428E
2582988
TUBE AS
246C, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C
246C, 256C, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C
2582983
TUBE AS
236D, 242D, 246C, 246D, 256C, 257D, 259D, 262C, 262C2, 262D, 272C, 272D, 272D XHP, 277C, 277C2, 277D, 279C, 279C2, 279D, 287C, 287C2, 287D, 289C, 289C2, 289D, 297C, 299C, 299D, 299D XHP
236D, 242D, 246C, 246D, 256C, 257D, 259D, 262C, 262C2, 262D, 272C, 272D, 272D XHP, 277C, 277C2, 277D, 279C, 279C2, 279D, 287C, 287C2, 287D, 289C, 289C2, 289D, 297C, 299C, 299D, 299D XHP
3149987
TUBE
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906H, 907H, 908H, C3.4
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906H, 907H, 908H, C3.4
3149983
TUBE
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906H, 907H, 908H, C3.4
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906H, 907H, 908H, C3.4
3149982
TUBE
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906H, 907H, 908H, C3.4
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906H, 907H, 908H, C3.4
3149981
TUBE
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906H, 907H, 908H, C3.4
236B, 236B3, 242B3, 246C, 252B, 252B3, 256C, 257B3, 259B3, 262C, 262C2, 272C, 277C, 277C2, 279C, 279C2, 287C, 287C2, 289C, 289C2, 297C, 299C, 3044C, 906H, 907H, 908H, C3.4