3598813 TUBE AS Caterpillar parts
314D LCR
Rating:
Alternative (cross code) number:
CA3598813
359-8813
3598813
CA3598813
359-8813
3598813
Weight: 9 pounds 4 kg.
EXCAVATOR,
Compatible equipment models: 3598813:
Number on catalog scheme:
26
For full view, you need register
Information:
Start By:a. remove valve covers
Do not let the tops of the fuel nozzles turn when the fuel lines are loosened. The nozzles will be damaged if the top of the nozzles turn in the body.
1. Use Tooling (A), and remove inner fuel injection lines (1). Install caps and plugs on all fuel injection line openings to keep dirt out of the fuel system. 2. Remove seal (2) from fuel injection line (1) if necessary. 3. Remove screw (3) from clamp (4) that holds fuel injection nozzle (5) in position. Clamp (4) cannot be removed until the fuel injection nozzle is lifted approximately 25.0 mm (1.00 in). 4. Remove the fuel injection nozzles with Tooling (B) as follows:a. Install 6V-6983 Adapter(6) and 6V-4152 Screw(7) into nozzle assembly (5). b. Install 6V-6982 Tube Assembly(8) over the 6V-4152 Screw.Use 2S-5658 Washer(9) and 1B-4206 Nut(10) on the 6V-4152 Screwto pull the fuel injection nozzle from the adapter.
A replacement of compression seal washer (11) and of carbon dam seal (12) must be made each time the fuel nozzle is removed. Be sure that the replacement compression seal washer (11) is the same color code and part number as the original compression seal washer. If the wrong thickness washer is used, engine damage could occur. See the topic "Fuel Injection Nozzle and Adapter" in the Specifications Manual for more detailed information.
5. Remove compression seal washer (11) and carbon dam seal (12) from fuel injection nozzle (5).Install Fuel Injection Nozzles
For later fuel injection nozzles, refer to Disassembly and Assembly document, SENR3920, "Fuel Injection Nozzles and Adapters".
*Part of 6V7020 Nozzle Puller Group. 1. Install compression seal washer (1), and use Tool (A) to install carbon dam seal (2) on the fuel injection nozzle.2. Make reference to Special Instruction SEHS7292 for the use of Tooling (C). 3. Use Tool (D) to clean adapter bore (3) for the fuel injection nozzle. Use an open end wrench or a tap driver to turn Tool (D). 4. Install fuel injection nozzle (4) and clamp (5) as a unit. Install the bolt in the clamp to hold it in place. 5. Install O-ring seal (6) on the inner fuel injection line.
Do not let the tops of the fuel nozzles turn when the fuel lines are tightened. The nozzles will be damaged if the top of the nozzles turn in the body.
6. Install inner fuel injection line (7). Use Tooling (B) to tighten the inner fuel line nuts to a torque of 40 7 N m (30 5 lb ft). For more information regarding the fuel injection nozzles, see the topic "Fuel Injection Nozzle And Adapter" in Specification SENR6523. End By:a. install valve covers
Do not let the tops of the fuel nozzles turn when the fuel lines are loosened. The nozzles will be damaged if the top of the nozzles turn in the body.
1. Use Tooling (A), and remove inner fuel injection lines (1). Install caps and plugs on all fuel injection line openings to keep dirt out of the fuel system. 2. Remove seal (2) from fuel injection line (1) if necessary. 3. Remove screw (3) from clamp (4) that holds fuel injection nozzle (5) in position. Clamp (4) cannot be removed until the fuel injection nozzle is lifted approximately 25.0 mm (1.00 in). 4. Remove the fuel injection nozzles with Tooling (B) as follows:a. Install 6V-6983 Adapter(6) and 6V-4152 Screw(7) into nozzle assembly (5). b. Install 6V-6982 Tube Assembly(8) over the 6V-4152 Screw.Use 2S-5658 Washer(9) and 1B-4206 Nut(10) on the 6V-4152 Screwto pull the fuel injection nozzle from the adapter.
A replacement of compression seal washer (11) and of carbon dam seal (12) must be made each time the fuel nozzle is removed. Be sure that the replacement compression seal washer (11) is the same color code and part number as the original compression seal washer. If the wrong thickness washer is used, engine damage could occur. See the topic "Fuel Injection Nozzle and Adapter" in the Specifications Manual for more detailed information.
5. Remove compression seal washer (11) and carbon dam seal (12) from fuel injection nozzle (5).Install Fuel Injection Nozzles
For later fuel injection nozzles, refer to Disassembly and Assembly document, SENR3920, "Fuel Injection Nozzles and Adapters".
*Part of 6V7020 Nozzle Puller Group. 1. Install compression seal washer (1), and use Tool (A) to install carbon dam seal (2) on the fuel injection nozzle.2. Make reference to Special Instruction SEHS7292 for the use of Tooling (C). 3. Use Tool (D) to clean adapter bore (3) for the fuel injection nozzle. Use an open end wrench or a tap driver to turn Tool (D). 4. Install fuel injection nozzle (4) and clamp (5) as a unit. Install the bolt in the clamp to hold it in place. 5. Install O-ring seal (6) on the inner fuel injection line.
Do not let the tops of the fuel nozzles turn when the fuel lines are tightened. The nozzles will be damaged if the top of the nozzles turn in the body.
6. Install inner fuel injection line (7). Use Tooling (B) to tighten the inner fuel line nuts to a torque of 40 7 N m (30 5 lb ft). For more information regarding the fuel injection nozzles, see the topic "Fuel Injection Nozzle And Adapter" in Specification SENR6523. End By:a. install valve covers
Caterpillar parts catalog:
Parts tube Caterpillar catalog:
311, 311B, 311C, 311D LRR, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D F...
2887698
TUBE AS
311D LRR, 312D, 312D L, 312D2, 312E, 312E L, 314D CR, 314D LCR
311D LRR, 312D, 312D L, 312D2, 312E, 312E L, 314D CR, 314D LCR
3937868
TUBE AS
311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR
311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR
3284828
TUBE AS
314D CR, 314D LCR
314D CR, 314D LCR
2181154
TUBE AS
314C, 314D CR, 314D LCR
314C, 314D CR, 314D LCR
2827510
TUBE AS
314D CR, 314D LCR, 314E CR, 314E LCR
314D CR, 314D LCR, 314E CR, 314E LCR
2452338
TUBE AS
314C, 314D CR, 314D LCR, 314E CR, 314E LCR
314C, 314D CR, 314D LCR, 314E CR, 314E LCR
3029667
TUBE AS
314D LCR
314D LCR
3598812
TUBE AS
314D LCR, 314E LCR
314D LCR, 314E LCR
3598811
TUBE AS
314D LCR, 314E LCR
314D LCR, 314E LCR
3598810
TUBE AS
314D LCR, 314E LCR
314D LCR, 314E LCR
3598809
TUBE AS
314D LCR
314D LCR
3598808
TUBE AS
314D LCR
314D LCR
3598807
TUBE AS
314D LCR
314D LCR
3504226
TUBE AS
314D LCR
314D LCR
3504224
TUBE AS
314D LCR
314D LCR
3504223
TUBE AS
314D LCR, 314E LCR
314D LCR, 314E LCR
3504222
TUBE AS
314D LCR
314D LCR
3598818
TUBE AS
314D LCR
314D LCR
3598816
TUBE AS
314D LCR
314D LCR