AVSPARE.COM
parts catalog

TUBE AS 3660788 - Caterpillar


3660788 TUBE AS Caterpillar parts
Rating:
21
Alternative (cross code) number:
CA3660788
366-0788
3660788
Caterpillar 3660788 TUBE AS

Buy TUBE AS 3660788 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 6 g00579262
Remove bolts (19), cover (18), and plug (20).
Illustration 7 g00579263
Install one bolt (19) into the flywheel housing through the hole for plug (20). Use Tooling (D) and a ratchet to turn the flywheel until bolt (19) can be installed through the hole and into the flywheel. This will position the No. 1 cylinder at the top center. Refer to the Service Manual, "Testing and Adjusting Module" for more information.
Illustration 8 g00579264
Place camshaft drive gears (8) into position on both of the camshafts.
Illustration 9 g00579145
Install timing ring (11) and the bolt on the camshaft that is on the left side of the engine. Ensure that the hole in the timing ring is properly seated on the locating pin.
Illustration 10 g00579141
Install plate (7) and the bolt on the camshaft that is on the right side of the engine.
Use the following steps to seat camshaft drive gears (8) onto the ends of the camshafts.
Tighten the bolt for timing ring (11) to a torque of 360 70 N m (265 52 lb ft).
Use a soft hammer to strike the bolt head for timing ring (11). This will help seat camshaft drive gear (8) on the camshaft.
Tighten the bolt for timing ring (11) again to a torque of 360 70 N m (265 52 lb ft).
Place an index mark on the bolt for timing ring (11).
Repeat Steps 22.b and 22.c until the bolt for timing ring (11) does not move after tightening the bolt. The marks should stay aligned.
Repeat Steps 22.a through 22.e in order to seat camshaft drive gear (8) on the opposite side of the engine.
Illustration 11 g00579261
Remove the timing pins from the camshafts (17). Install the timing pins in original locations (16).
Illustration 12 g00579522
Install the gaskets and two covers (6) over the camshaft drive gears on both sides of the engine.
Illustration 13 g00579263
Illustration 14 g00579262
Remove bolt (19) from the flywheel. Install plug (20) in the timing hole. Remove Tooling (D) and install cover (18) with bolts (19) on the flywheel housing.
Illustration 15 g00613620
Illustration 16 g00613619
Install two covers (4) on the front housing.
Install electronic control module (3). See Disassembly and Assembly, "Electronic Control Moduel (Engine) - Remove and Install".
Illustration 17 g00613660
Remove the O-ring seals from valve lifters (5). Push the valve lifters against the camshaft.
Illustration 18 g00613617
Install access covers (2) and tube assemblies (1) on both sides of the engine. End By:
Install the speed/timing sensor. See the Service Manual, "Electronic Troubleshooting" module.
Install the rocker shaft assemblies and the pushrods.


Parts tube Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.