AVSPARE.COM
parts catalog

TUBE AS 3904702 - Caterpillar



3904702 TUBE AS Caterpillar parts 950K, 962K TUBE
Rating:
22
Alternative (cross code) number:
CA3904702
390-4702
3904702
Caterpillar 3904702 TUBE AS
Weight: 1 pounds 0 kg.

Buy TUBE AS 3904702 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 3904702:

WHEEL LOADER  950K   962K   Caterpillar
Number on catalog scheme: 52
 
  For full view, you need register

Information:


Measuring Rolling Torque
(A) Torque wrench. (B) Direction of pull. (C) Viewed standing here.1. Use a torque wrench as illustrated above to determine the rolling torque created by the seal and boot. A typical rolling torque value is 3.4 N m (30 lb in).1. After seal (1), boot (2) and bearing cone (3) have been installed in hub (9), install spindle (8) into hub (9). Hold the spindle stationary and use a torque wrench as illustrated above to determine the rolling torque created by the seal and boot. A typical rolling torque value is 3.4 N m (30 lb in). Bearing cones (3) and (4) should be clean and wiped dry of any lubricating oil. Bearing cones which have oil present will affect rolling torque readings.2. Heat shaft bearing cone (4) in an oven to 135°C (275°F). Press in the shaft bearing cone until the rolling torque increases 1.7 to 4.5 N m (15 to 40 lb in) greater than the value measure in Step (A). It will be necessary to continually rotate the housing to seat the bearing cone in order to obtain a correct rolling resistance.3. Apply 9S3263 Thread Lock to the threads of the locknut. Install washer (5), lock tanged washer (6) and locknut (7).4. Tighten the locknut with a torque wrench to 306 N m (225 lb ft). Rotate hub (9) to seat the bearings.5. Recheck the rolling torque. The final reading should be 1.7 to 4.5 N m (15 to 40 lb in) greater than the value measure in Step (A).6. A final rolling torque of 5 to 7 N m (45 to 65 lb in) should result in a bearing preload of .025 to .051 mm (.0010 to .0020 in).7. If the lockwasher tang does not line up with the locknut slot, tighten the locknut to line up the tang and bend into the locknut slot.(10) Torque for eight bolts ... 20 to 25 N m (15 to 20 lb ft) Four shoulder bolts (2) are equally spaced.(11) Torque for four shoulder bolts ... 20 to 25 N m (15 to 20 lb ft)

Caterpillar parts catalog:

Caterpillar parts catalog
950K Wheel Loader R4A00001-UP (MACHINE) POWERED BY C7.1 Engine
962K Wheel Loader X4T00001-UP (MACHINE) POWERED BY C7.1 Engine
962K Wheel Loader FLL00001-UP (MACHINE) POWERED BY C7.1 Engine


Parts tube Caterpillar catalog:

3304693 TUBE AS
950K, 962K, M313D, M315D, M315D 2, M316D, M317D 2
2678575 TUBE
120K, 120K 2, 12K, 140K, 140K 2, 160K, 24M, 305.5E, 308E, 308E2 CR, 583T, 587T, 621H, 621K, 623H, 623K, 623K LRC, 627H, 627K, 627K LRC, 770G, 770G OEM, 772G, 772G OEM, 824K, 825K, 826K, 834K, 836K, 90...
1660020 TUBE
950K, 962K, 966H
3553679 TUBE AS
950K, 962K, FUSION
3229066 TUBE AS
24M, 950K, 962K
3645870 TUBE AS
950K, 962K, 966K, 972K, 980K, 980K HLG
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.