4360494 TUBE AS Caterpillar parts
3512C, SPF343C
Rating:
Alternative (cross code) number:
CA4360494
436-0494
4360494
CA4360494
436-0494
4360494
Weight: 9 pounds 4 kg.
PETROLEUM ENGINE, PUMPER,
Information:
Towing a Disabled Machine
Personal injury or death could result when towing a disabled machine incorrectly.Block the machine to prevent movement before releasing the brakes. The machine can roll free if it is not blocked.Follow the recommendations below, to properly perform the towing procedure.
For information on hitch capacities, towing with the standard retrieval hitch and towing with the hydraulic towing hitch refer to this Operation and Maintenance Manual, "Operation Information".Only tow the machine over short distances at a low speed. Move the machine at a speed of 8 km/h (5 mph) or less to a convenient location for repair. Always load the machine onto a suitable transport vehicle if long distance moving is required. If a suitable transport vehicle is unavailable, remove the drive shaft and raise the front wheels off the ground before you tow the machine. The parking brake must be engaged on the disabled machine, and the wheels must be chocked.The boom must be fully retracted, lowered and the load must be removed before towing the machine. If hydraulic power is not available, refer to Operation and Maintenance Manual, "Equipment Lowering with Engine Stopped" in order to retract the boom and lower the boom.Do not use chains for towing a machine. Chain links can break with no warning. Use a wire rope with ends that have loops or rings or use a rigid tow bar. Before the machine is towed, make sure that the tow line or tow bar is in good condition. Make sure that the tow line or tow bar has enough strength for the conditions that will be encountered. The tow line or tow bar should be able to pull at least 150 percent of the gross weight of the towed machine. This pertains to towing a disabled machine from mud and to towing a machine on a grade.
Illustration 1 g00809994
For towing or retrieving the machine from the front, towing equipment should be attached to lifting point (1) on the frame at the front of the machine.
Illustration 2 g00809995
Typical Retrieval Hitch (Rear)For towing or retrieving the machine from the rear, attach the tow line or tow bar to retrieval hitch (2) at the rear of the machine.
Illustration 3 g00809998
The machine has a hydraulic drive system. Open two bypass valves (3) before you tow the machine. The two bypass valves are located on the hydraulic pump.
Illustration 4 g00810208
The above photograph shows a typical example of the pump.Hold nuts (4) in position. At the same time turn nuts (5) in a counterclockwise direction by three full turns in order to open both bypass valves.Note: Do not turn nuts (5) counterclockwise by more than three full turns.Normally, the towing machine should be at least the size of the disabled machine. Make sure that the towing machine has enough brake capacity, weight and power. The towing machine must be able to control both machines for the grade, distance and conditions that are involved.A larger towing machine and a solid tow bar will be required in order to
Personal injury or death could result when towing a disabled machine incorrectly.Block the machine to prevent movement before releasing the brakes. The machine can roll free if it is not blocked.Follow the recommendations below, to properly perform the towing procedure.
For information on hitch capacities, towing with the standard retrieval hitch and towing with the hydraulic towing hitch refer to this Operation and Maintenance Manual, "Operation Information".Only tow the machine over short distances at a low speed. Move the machine at a speed of 8 km/h (5 mph) or less to a convenient location for repair. Always load the machine onto a suitable transport vehicle if long distance moving is required. If a suitable transport vehicle is unavailable, remove the drive shaft and raise the front wheels off the ground before you tow the machine. The parking brake must be engaged on the disabled machine, and the wheels must be chocked.The boom must be fully retracted, lowered and the load must be removed before towing the machine. If hydraulic power is not available, refer to Operation and Maintenance Manual, "Equipment Lowering with Engine Stopped" in order to retract the boom and lower the boom.Do not use chains for towing a machine. Chain links can break with no warning. Use a wire rope with ends that have loops or rings or use a rigid tow bar. Before the machine is towed, make sure that the tow line or tow bar is in good condition. Make sure that the tow line or tow bar has enough strength for the conditions that will be encountered. The tow line or tow bar should be able to pull at least 150 percent of the gross weight of the towed machine. This pertains to towing a disabled machine from mud and to towing a machine on a grade.
Illustration 1 g00809994
For towing or retrieving the machine from the front, towing equipment should be attached to lifting point (1) on the frame at the front of the machine.
Illustration 2 g00809995
Typical Retrieval Hitch (Rear)For towing or retrieving the machine from the rear, attach the tow line or tow bar to retrieval hitch (2) at the rear of the machine.
Illustration 3 g00809998
The machine has a hydraulic drive system. Open two bypass valves (3) before you tow the machine. The two bypass valves are located on the hydraulic pump.
Illustration 4 g00810208
The above photograph shows a typical example of the pump.Hold nuts (4) in position. At the same time turn nuts (5) in a counterclockwise direction by three full turns in order to open both bypass valves.Note: Do not turn nuts (5) counterclockwise by more than three full turns.Normally, the towing machine should be at least the size of the disabled machine. Make sure that the towing machine has enough brake capacity, weight and power. The towing machine must be able to control both machines for the grade, distance and conditions that are involved.A larger towing machine and a solid tow bar will be required in order to
Caterpillar parts catalog:
Parts tube Caterpillar catalog:
2984542
TUBE AS
420E, 430E, 450E, 914G, AP555E, BG500E, C4.4, CB-54, CB-54B, CB-64, CP-44, CS-44, CS-54, CS-54B, CW-34, D3K XL, D4K XL, D5K LGP, IT14G, IT14G2, M313D, M315D, M315D 2, M317D 2, SPF343C
420E, 430E, 450E, 914G, AP555E, BG500E, C4.4, CB-54, CB-54B, CB-64, CP-44, CS-44, CS-54, CS-54B, CW-34, D3K XL, D4K XL, D5K LGP, IT14G, IT14G2, M313D, M315D, M315D 2, M317D 2, SPF343C
7C7678
TUBE AS
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D...
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D...
7C7677
TUBE AS
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D...
3508, 3508B, 3508C, 3512, 3512B, 3512C, 3516, 3516B, 3516C, 5130, 5130B, 5230, 5230B, 776C, 776D, 777, 777B, 777C, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793D...
2071372
TUBE AS
3512B, 3512C, 3516B, 3516C, SPF343C, TH48-E80
3512B, 3512C, 3516B, 3516C, SPF343C, TH48-E80
2940093
TUBE AS
3512C, 3516B, 3516C, TH48-E80
3512C, 3516B, 3516C, TH48-E80
5M6212
TUBE
14E, 30/30, 572G, 611, 615, 615C, 621, 621B, 621E, 621F, 621G, 621H, 621K, 621R, 623, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637E, 69D, 735, 735B, ...
14E, 30/30, 572G, 611, 615, 615C, 621, 621B, 621E, 621F, 621G, 621H, 621K, 621R, 623, 623B, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627B, 627E, 627F, 627G, 627H, 627K, 627K LRC, 637E, 69D, 735, 735B, ...
2860616
TUBE AS
3512C, TH48-E80
3512C, TH48-E80
2865726
TUBE
3512C, TH48-E80
3512C, TH48-E80
2860624
TUBE
3512C, TH48-E80
3512C, TH48-E80
2673398
TUBE AS
3512B, 3512C, SPF343C, TH48-E80, TH55-E70
3512B, 3512C, SPF343C, TH48-E80, TH55-E70
4360499
TUBE
3512C, SPF343C
3512C, SPF343C
3552306
TUBE AS
3512C, TH55-E70
3512C, TH55-E70
4360493
TUBE AS
3512C, SPF343C
3512C, SPF343C
4360492
TUBE AS
3512C, SPF343C
3512C, SPF343C
3215991
TUBE AS
3512C, SPF343C, TH48-E80
3512C, SPF343C, TH48-E80
3215987
TUBE AS
3512C, SPF343C, TH48-E80
3512C, SPF343C, TH48-E80
3215951
TUBE AS
3512C, SPF343C, TH48-E80
3512C, SPF343C, TH48-E80
2911498
TUBE AS
3512C, TH48-E80
3512C, TH48-E80
2749377
TUBE AS
3512B, 3512C, SPF343C, TH48-E80, TH55-E70
3512B, 3512C, SPF343C, TH48-E80, TH55-E70
2737586
TUBE AS
3512B, 3512C, SPF343C, TH48-E80, TH55-E70
3512B, 3512C, SPF343C, TH48-E80, TH55-E70
2673398
TUBE AS
3512B, 3512C, SPF343C, TH48-E80, TH55-E70
3512B, 3512C, SPF343C, TH48-E80, TH55-E70
4263526
TUBE
3512C, SPF343C
3512C, SPF343C
4360502
TUBE AS
3512C, SPF343C
3512C, SPF343C
4360497
TUBE AS
3512C, SPF343C
3512C, SPF343C