4500701 TUBE AS Caterpillar parts
Rating:
Alternative (cross code) number:
CA4500701
450-0701
4500701
CA4500701
450-0701
4500701
Weight: 5 pounds 2 kg.
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$36.95
03 Aug 2017
3.00[1.35] pounds
Custom Hood Protector: Custom Hood Pro
Custom Hood Protector 45007-01 Protects vehicle's hood from all weather conditions. Durable leather grain vinyl is micro-perforated to allow moisture to evaporate. Custom tailored for a sleek snug fit. Hood Guard
Number on catalog scheme:
2
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 2
B - Loctite
Black Contact Adhesive -
C - Loctite
SuperFlex 596 High Temp RTV Silicone Adhesive - Red - Start By:
Remove the turbochargers.
Remove the accessory drive, if necessary.
Remove the starting motors.
Remove the manual barring group.
Remove the camshaft drive gears.
Remove the crankshaft rear seal.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Remove the bolts that hold the engine oil pan to the rear housing.
Illustration 1 g01302559
Typical example
Attach Tooling (A) and a suitable lifting device to rear housing (2). The weight of rear housing (2) is approximately 455 kg (1000 lb).
Remove bolts (1) that are inside the opening for the accessory drive.
Remove bolts (3) that are inside each camshaft drive gear opening.
Remove bolts (4) that hold rear housing (2) in position. Remove rear housing (2) from the cylinder block.
Remove the gasket and the O-ring seals from the cylinder block. Installation Procedure
Place the gasket and the O-ring seals in position on the rear of the cylinder block.
Trim the gasket that is located between the rear housing and the cylinder block. Trim this gasket even with the bottom of the cylinder block.
Apply Tooling (B) to the engine oil pan and replace the section of the gasket for the engine oil pan. Apply Tooling (C) to the top of the section of the new gasket. Apply Tooling (C) to the intersection of the cylinder block, engine oil pan, and rear housing. Tooling (C) will assist with installation of the rear housing.
Illustration 2 g01302559
Typical example
Attach Tooling (A) and a suitable lifting device to rear housing (2). The weight of rear housing (2) is approximately 455 kg (1000 lb).
Place rear housing (2) in position on the cylinder block. Install the following bolts: (1), (3) and (4).
Place the support brackets for the turbochargers in position on the rear housing. Install the bolts that hold the support brackets in place.
Tighten bolts (1), (3), and (4) to the correct torque. Refer to Specifications, "Housing (Rear)" for the correct tightening sequence.
Install the bolts that hold the engine oil pan to the rear housing. End By:
Install the crankshaft rear seal.
Install the camshaft drive gears.
Install the manual barring group.
Install the starting motors.
Install the accessory drive, if necessary.
Install the turbochargers.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 439-3940 Link Bracket 2
B - Loctite
Black Contact Adhesive -
C - Loctite
SuperFlex 596 High Temp RTV Silicone Adhesive - Red - Start By:
Remove the turbochargers.
Remove the accessory drive, if necessary.
Remove the starting motors.
Remove the manual barring group.
Remove the camshaft drive gears.
Remove the crankshaft rear seal.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Remove the bolts that hold the engine oil pan to the rear housing.
Illustration 1 g01302559
Typical example
Attach Tooling (A) and a suitable lifting device to rear housing (2). The weight of rear housing (2) is approximately 455 kg (1000 lb).
Remove bolts (1) that are inside the opening for the accessory drive.
Remove bolts (3) that are inside each camshaft drive gear opening.
Remove bolts (4) that hold rear housing (2) in position. Remove rear housing (2) from the cylinder block.
Remove the gasket and the O-ring seals from the cylinder block. Installation Procedure
Place the gasket and the O-ring seals in position on the rear of the cylinder block.
Trim the gasket that is located between the rear housing and the cylinder block. Trim this gasket even with the bottom of the cylinder block.
Apply Tooling (B) to the engine oil pan and replace the section of the gasket for the engine oil pan. Apply Tooling (C) to the top of the section of the new gasket. Apply Tooling (C) to the intersection of the cylinder block, engine oil pan, and rear housing. Tooling (C) will assist with installation of the rear housing.
Illustration 2 g01302559
Typical example
Attach Tooling (A) and a suitable lifting device to rear housing (2). The weight of rear housing (2) is approximately 455 kg (1000 lb).
Place rear housing (2) in position on the cylinder block. Install the following bolts: (1), (3) and (4).
Place the support brackets for the turbochargers in position on the rear housing. Install the bolts that hold the support brackets in place.
Tighten bolts (1), (3), and (4) to the correct torque. Refer to Specifications, "Housing (Rear)" for the correct tightening sequence.
Install the bolts that hold the engine oil pan to the rear housing. End By:
Install the crankshaft rear seal.
Install the camshaft drive gears.
Install the manual barring group.
Install the starting motors.
Install the accessory drive, if necessary.
Install the turbochargers.
Caterpillar parts catalog:
Parts tube Caterpillar catalog:
4500697
TUBE AS
Caterpillar
Caterpillar
4500696
TUBE AS
Caterpillar
Caterpillar
4438156
TUBE AS
Caterpillar
Caterpillar
4364011
TUBE AS
Caterpillar
Caterpillar
4219697
TUBE AS
Caterpillar
Caterpillar
4200037
TUBE AS
Caterpillar
Caterpillar
4687217
TUBE AS
Caterpillar
Caterpillar
4681682
TUBE GP-EXTENSION
Caterpillar
Caterpillar
4661027
TUBE AS
Caterpillar
Caterpillar
4559609
TUBE
Caterpillar
Caterpillar
4528683
TUBE AS
Caterpillar
Caterpillar
4503125
TUBE-AIR
Caterpillar
Caterpillar