AVSPARE.COM
parts catalog

TUBE 5088125 - Caterpillar



5088125 TUBE Caterpillar parts TUBE
Rating:
86
Alternative (cross code) number:
CA5088125
508-8125
5088125
Caterpillar 5088125 TUBE
Weight: 10 pounds 4 kg.

Buy TUBE 5088125 Caterpillar genuine, new aftermarket tractor parts with delivery

Number on catalog scheme: 6
 
  For full view, you need register

Information:

THE CROSS SLOPE SENSOR IS A PRECISION INSTRUMENT THAT IS ACCURATELY CALIBRATED AT THE FACTORY. DO NOT ADJUST OR CHANGE THE POSITION OF THE POINTER, THE ADJUSTMENT GUIDE BLOCK, THE ADJUSTMENT SHAFT BEARINGS OR THE BELT THAT EXTENDS FROM THE ADJUSTMENT SHAFT TO THE SLOPE INDICATOR. IF NECESSARY, ADJUST BELT TENSION BY MOVING THE INDICATOR SUPPORT BRACKET. DO NOT MOVE THE ADJUSTMENT SHAFT BEARINGS.The cross slope sensor is accurately calibrated to the cutter before the machine leaves the factory and will not normally require any further adjustment. If the machine is not cutting to the slope set in the slope indicator, the calibration of the cross slope sensor can be checked as follows:1. Check the cutter bits for even wear. If the bits are not evenly worn, replace all bits.2. Position the machine on a level slab.3. Set the slope indicator to "O", the right side elevation lever to "Auto" and the right side elevation automatic mode selector lever to "Slope".4. Start the engine and set the cutter to rotate slowly.5. Use the left front and left rear elevation control levers to manually lower the mainframe evenly until the cutter bits on the left end of the cutter are just contacting the slab and the mainframe is level fore and aft. If the cutter bits are all just contacting the slab, the cutter is level. Proceed with normal operation of the machine. 6. If the cutter is not level, check the alignment of the pointer on the pendulum assembly and the line on the adjustment guide block. Turn the slope handwheel as necessary to align the pointer and the line. 7. Check to see if the slope indicator is on "O". If not, loosen the slope indicator mounting bracket, hold the pendulum shaft so it will not turn, remove the belt from the pulleys and then turn the slope indicator shaft to set the slope indicator at "O". Replace the belt, slide the mounting bracket down to tighten the belt, then tighten the nuts.8. Repeat steps 1 through 5.9. If the cutter still is not level, turn the slope selector in the direction needed to level the cutter and repeat steps 1 through 5. Repeat until the cutter is level. DO NOT MOVE THE SLOPE SELECTOR ONCE THE CUTTER IS LEVEL. 10. Place an 8-inch mechanic's level on top of the adjustment guide block and parallel to the adjustment shaft. 11. Move the nuts up or down on the threaded shafts as necessary to level the adjustment guide block, tighten the nuts and recheck the level of the guide block.12. Set the slope indicator to "O" and repeat steps 1 through 5.13. Recheck the level of the adjustment guide block. Both the cutter and the adjustment guide block should be level. If not, repeat steps 9 through 11.14. Proceed with normal operation of the machine. If the machine does not cut Slope Right or Slope Left according to the slope indicator, see "Calibrating the Cross Slope Sensor"

Caterpillar parts catalog:

Caterpillar parts catalog
C32 Generator Set FLX00001-UP
C32 Generator Set PAE00001-UP
C32 Generator SET JSJ00001-UP
C32 Generator Set P7E00001-UP


Parts tube Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.