AVSPARE.COM
parts catalog

TUBE AS 5088177 - Caterpillar



5088177 TUBE AS Caterpillar parts TUBE
Rating:
11
Alternative (cross code) number:
CA5088177
508-8177
5088177
Caterpillar 5088177 TUBE AS
Weight: 0.33 pounds 0 kg.

Buy TUBE AS 5088177 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 6 g01449291
(21) 200-0996 Ring (22) 199-5333 Sleeve (23) 199-5332 Sleeve (24) 225-9266 Sprocket (25) 8S-6212 Bolt (26) 1K-6872 Locknut
Disassemble the sprocket group. Refer to Illustration 6.Discard outer sleeves (22), inner sleeves (23), bolts (25), and locknuts (26). Retain rings (21) and sprocket (24) for the reassembly of the sprocket group.ReferenceDisassembly and Assembly, "Track Drive - Disassemble".
Illustration 7 g01449282
(21) 200-0996 Ring (24) 225-9266 Sprocket (27) 199-5333 Sleeve (28) 199-5332 Sleeve (29) 8S-6212 Bolt (30) 1K-6872 Locknut
Reassemble the sprocket group. Use the parts that are identified in Illustration 7.Note: Rings (21) and the Sprocket (24) are reused in the reassembly of the sprocket group. Tighten the bolts to a torque of 120 20 N m (90 15 lb ft).ReferenceDisassembly and Assembly, "Track Drive - Assemble".
Illustration 8 g01449285
Reinstall the sprocket group. Secure the sprocket group with 12 bolts (19) and 12 washers (20). Tighten the bolts to a torque of 270 40 N m (200 30 lb ft). Refer to Illustration 8.
Illustration 9 g01449289
Install 278-1240 Sprocket Bearing Group (27) .
Illustration 10 g01449283
Install retaining ring (12) onto the machine with tool (A) .
Illustration 11 g01453525
Illustration 12 g03319847
Illustration 13 g03319851
Place plate assembly (17) onto the machine. Secure plate assembly (17) onto the machine with four bolts (32) and four lockwashers (33). Tighten the bolts to a torque of 105 20 N m (75 15 lb ft).Also place two locknuts (15), lockwashers (16), and bolts (18) onto the machine. Tighten the bolts to a torque of 120 20 N m (90 15 lb ft). Place 278-1259 Cap (34) onto the machine. Install 8J-7636 Retaining Ring (38) after installation of 278-1259 Cap (34) .ReferenceDisassembly and Assembly, "Track Drive - Install".
Illustration 14 g01449431
Illustration 15 g01449432
Place 261-6300 Idler Wheel Group (36) and plate (4) onto the machine. Secure 261-6300 Idler Wheel Group (36) into place with bolt (1) and lockwasher (2). Tighten the bolts to a torque of 50 10 N m (35 7 lb ft).Place the new idler group on the front and on the rear.ReferenceDisassembly and Assembly, "Idler Wheel - Install".
Illustration 16 g01449529
Install the new 220-8161 Track (37) .ReferenceDisassembly and Assembly, "Track (Rubber) - Remove and Install".
Repeat this procedure for the opposite side of the machine.


Parts tube Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.