6K6612 TUBE ASSEM. (Left Hand) Caterpillar parts
920, 930, 930R
Rating:
Alternative (cross code) number:
CA6K6612
6K-6612
6K6612
CA6K6612
6K-6612
6K6612
Weight: 1 pounds 0 kg.
WHEEL LOADER,
Compare Prices:
As an associate, we earn commssions on qualifying purchases through the links below
$73.28
23 Mar 2024
Amazon.com
CTP 6K6612 Tube Fittings for Models 920/930/930R
CTP For Models 920/930/930R || Highly Efficient || Easy in-and-out fit
CTP For Models 920/930/930R || Highly Efficient || Easy in-and-out fit
$77.35
26 Feb 2024
Amazon.com
CTP 6K6612 Tube Fittings for Models 920/930/930R
CTP For Models 920/930/930R || Highly Efficient || Easy in-and-out fit
CTP For Models 920/930/930R || Highly Efficient || Easy in-and-out fit
$62.42
10 Feb 2022
US: Florida-Parts-Z
6K6612 - Tube ASSEM. (Left Hand) for Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
Number on catalog scheme:
20
For full view, you need register
Caterpillar parts catalog:
Information:
Remove Piston Cooling Tubes
Start By:a. remove oil pump 1. Turn the crankshaft until pistons are clear of the piston cooling tube to be removed.2. Remove bolt (1) that holds the piston cooling tube. Remove the piston cooling tube.Install Piston Cooling Tubes
If the piston cooling jets are to be reused, check the alignment of the piston cooling jet tube with Tool (A). See Special Instructions, SMHS7267, for instructions on the use of the piston cooling jet alignment tool group.1. Put the piston cooling tube in position on the cylinder block and install the bolt that holds the piston cooling tube to the block.2. Tighten the bolt to a torque of 25 7 N m (18 5 lb ft) (3408 Engine). Tighten the bolt to a torque of 25 7 N m (18 5 lb ft) (3412 Engine).3. With the piston at the bottom of the bore, check the clearance between piston and piston cooling tube with a piece of wire (1) 0.63 mm (.025 in) thick. If the clearance is less than 0.63 mm (.025 in) make a replacement of the piston cooling tube. The piston cooling tubes must fit evenly against the cylinder block. If they do not, it will cause an oil loss in the engine oil system.End By:a. install oil pump
Start By:a. remove oil pump 1. Turn the crankshaft until pistons are clear of the piston cooling tube to be removed.2. Remove bolt (1) that holds the piston cooling tube. Remove the piston cooling tube.Install Piston Cooling Tubes
If the piston cooling jets are to be reused, check the alignment of the piston cooling jet tube with Tool (A). See Special Instructions, SMHS7267, for instructions on the use of the piston cooling jet alignment tool group.1. Put the piston cooling tube in position on the cylinder block and install the bolt that holds the piston cooling tube to the block.2. Tighten the bolt to a torque of 25 7 N m (18 5 lb ft) (3408 Engine). Tighten the bolt to a torque of 25 7 N m (18 5 lb ft) (3412 Engine).3. With the piston at the bottom of the bore, check the clearance between piston and piston cooling tube with a piece of wire (1) 0.63 mm (.025 in) thick. If the clearance is less than 0.63 mm (.025 in) make a replacement of the piston cooling tube. The piston cooling tubes must fit evenly against the cylinder block. If they do not, it will cause an oil loss in the engine oil system.End By:a. install oil pump
Parts tube Caterpillar catalog:
120B, 120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 235, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C,...
120B, 120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 235, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C,...
930, 950, 966C, D6C
518, 920, 930, 950, 966C
920, 930, 930R
920, 930, 930R
920, 930
920, 930
518, 930, 930R, 950
920, 950
920, 930, 930R
7K0413
TUBE ASSEM.
920, 930, 930R
920, 930, 930R
1S5381
TUBE ASSEM.
621, 623
621, 623
4S7868
TUBE (Oil Cooler Drain)
621, 980
621, 980