7C2184 TUBE AS-WATER INLET LINE Caterpillar parts
416, 426, 428, 436
Rating:
Alternative (cross code) number:
CA7C2184
7C-2184
7C2184
CA7C2184
7C-2184
7C2184
Weight: 0.95 pounds 0 kg.
BACKHOE LOADER,
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: This procedure assumes that the housing (front) is still on the engine. Do not follow this procedure if the housing (front) has been removed from the engine. Refer to this Disassembly and Assembly Manual, "Housing (Front) - Install" if the housing (front) has been removed from the engine.
Clean the oil seal housing (8) and inspect the oil seal housing for damage. If necessary, replace the housing (front). Refer to this Disassembly and Assembly Manual, "Housing (Front) - Remove and Housing (Front) - Install".
Check the face on the pulley that contacts the crankshaft front seal for wear. If necessary, repair the crankshaft pulley. Refer to this Disassembly and Assembly Manual, "Crankshaft Wear Sleeve (Front) - Remove and Crankshaft Wear Sleeve (Front) - Install" for further details. Note: A sleeve (5) is attached to the new crankshaft front seal (6). Do not remove the sleeve (5) at this time. Discard the new crankshaft front seal (6) if the sleeve (5) is not installed on the new crankshaft front seal.
Illustration 1 g01148784
The Tooling (A) includes items 1, 2, 3, 4, 7 and 9.
Install the fastener plate (7) onto the front of the crankshaft. Install the nut (1) and the pressure plate (2) onto the threaded bar (3). Note: Do not lubricate the crankshaft front seal (6). Do not lubricate the oil seal housing (8).
Ensure that the lip of the crankshaft front seal that is spring loaded is facing toward the inside of the front housing and that it is square with the bore of the housing for the crankshaft front seal.
Align the assembly of the sleeve (5) and the crankshaft front seal (6) to the front of the oil seal housing (8).
Install the adapter (4) onto the sleeve (5).
Install the pressure plate (2) onto the adapter (4) and tighten the threaded bar (3) onto the fastener plate (7). Check the alignment of the assembly and the crankshaft front seal (6) to the oil seal housing (8).
Insert a suitable rod through the hole (9) in the threaded bar (3) in order to prevent the threaded rod from turning as the nut (1) is tightened. Tighten the nut (1) in order to push the crankshaft front seal (6) into the oil seal housing (8). Continue to tighten the nut (1) until contact is made with the bottom face of the oil seal housing (8).
Turn the sleeve (5) counterclockwise and pull the sleeve at the same time in order to remove the sleeve from the oil seal housing (8). Remove the adapter (7).
Immediately install the crankshaft pulley. Refer to this Disassembly and Assembly Manual, "Crankshaft Pulley - Remove and Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6210 Front Seal Installer 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: This procedure assumes that the housing (front) is still on the engine. Do not follow this procedure if the housing (front) has been removed from the engine. Refer to this Disassembly and Assembly Manual, "Housing (Front) - Install" if the housing (front) has been removed from the engine.
Clean the oil seal housing (8) and inspect the oil seal housing for damage. If necessary, replace the housing (front). Refer to this Disassembly and Assembly Manual, "Housing (Front) - Remove and Housing (Front) - Install".
Check the face on the pulley that contacts the crankshaft front seal for wear. If necessary, repair the crankshaft pulley. Refer to this Disassembly and Assembly Manual, "Crankshaft Wear Sleeve (Front) - Remove and Crankshaft Wear Sleeve (Front) - Install" for further details. Note: A sleeve (5) is attached to the new crankshaft front seal (6). Do not remove the sleeve (5) at this time. Discard the new crankshaft front seal (6) if the sleeve (5) is not installed on the new crankshaft front seal.
Illustration 1 g01148784
The Tooling (A) includes items 1, 2, 3, 4, 7 and 9.
Install the fastener plate (7) onto the front of the crankshaft. Install the nut (1) and the pressure plate (2) onto the threaded bar (3). Note: Do not lubricate the crankshaft front seal (6). Do not lubricate the oil seal housing (8).
Ensure that the lip of the crankshaft front seal that is spring loaded is facing toward the inside of the front housing and that it is square with the bore of the housing for the crankshaft front seal.
Align the assembly of the sleeve (5) and the crankshaft front seal (6) to the front of the oil seal housing (8).
Install the adapter (4) onto the sleeve (5).
Install the pressure plate (2) onto the adapter (4) and tighten the threaded bar (3) onto the fastener plate (7). Check the alignment of the assembly and the crankshaft front seal (6) to the oil seal housing (8).
Insert a suitable rod through the hole (9) in the threaded bar (3) in order to prevent the threaded rod from turning as the nut (1) is tightened. Tighten the nut (1) in order to push the crankshaft front seal (6) into the oil seal housing (8). Continue to tighten the nut (1) until contact is made with the bottom face of the oil seal housing (8).
Turn the sleeve (5) counterclockwise and pull the sleeve at the same time in order to remove the sleeve from the oil seal housing (8). Remove the adapter (7).
Immediately install the crankshaft pulley. Refer to this Disassembly and Assembly Manual, "Crankshaft Pulley - Remove and Install".
Caterpillar parts catalog:
Parts tube Caterpillar catalog:
5P5630
TUBE-ETHER FITTING TO MANIFOLD (8 DM)
1090, 1190, 1190T, 120B, 120G, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140B, 140G, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14H, ...
1090, 1190, 1190T, 120B, 120G, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140B, 140G, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14H, ...
416B, 416C, 426B, 426C, 428, 428B, 428C, 436C, 438C
9R0854
TUBE AS
428
428
9R2513
TUBE AS
416, 426, 428, 436
416, 426, 428, 436
9R1979
TUBE AS
428, 438
428, 438
9R5250
TUBE AS
428
428
9R5575
TUBE AS
426
426
9R1470
TUBE AS
416, 426, 428, 436
416, 426, 428, 436
9R4313
TUBE AS
426
426
9R6766
TUBE AS
436, 438
436, 438
9R1863
TUBE AS
426, 436
426, 436
416, 426, 436
120H, 120H ES, 120H NA, 135H, 135H NA, 214B, 3114, 3116, 3126, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 446B, 446D, 45, 525B, 533, 535B, 539, 543, 55, 550, 570, 574, 580, 613C I...
120H, 120H ES, 120H NA, 135H NA, 213B, 214B, 224B, 3116, 3126, 320 L, 325, 325 L, 325 LN, 45, 55, 928G, 938F, 938G, 950F, 950F II, 950G, 953B, 953C, 960F, 962G, 963B, AP-1000, AP-1050, BG-2455C, BG-24...
213B, 3114, 3116, 446B, 950F, 950F II, 953B, 960F, AP-1000, AP-1050, CB-434, CB-634C, CP-563, IT12B, IT28F
120H, 120H ES, 120H NA, 135H, 135H NA, 205B, 211B, 213B, 214B, 224B, 3114, 3116, 3126, 35, 446B, 446D, 45, 525B, 533, 535B, 539, 543, 55, 550, 561M, 570, 574, 580, 613C II, 918F, 924F, 928G, 938F, 938...
120H, 120H ES, 120H NA, 135H, 135H NA, 214B, 3114, 3116, 3126, 320 L, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 35, 446B, 446D, 45, 525B, 533, 535B, 539, 543, 55, 550, 561M, 570, 574, 5...
214B, 3116, 3126, 525B, 535B, 539, 550, 561M, 570, 574, 580, 928G, 938F, 938G, 950F, 950F II, 950G, 953C, 960F, 962G, 963B, 963C, AP-1000, AP-1000B, AP-1050, AP-1055B, AP-900B, BG-2455C, BG-245C, CB-6...
8R7879
TUBE
65, 75
65, 75
9R7856
TUBE AS
416, 426, 436
416, 426, 436
5G8830
TUBE AS
65, 75
65, 75
3W9791
TUBE AS
65, 75
65, 75
5P0580
TUBE (8 DM)-ETHER FITTING TO MANIFOLD
225, 416, 416B, 426, 428, 428B, 518, 528, 571G, 572G, 594H, 611, 615C, 631E, 631G, 633E II, 637E, 637G, 815, 816, 910, 920, 930, 930R, 933, 933C, 939, 939C, 941, 943, 950, 951B, 953, 953C, 955K, 955L,...
225, 416, 416B, 426, 428, 428B, 518, 528, 571G, 572G, 594H, 611, 615C, 631E, 631G, 633E II, 637E, 637G, 815, 816, 910, 920, 930, 930R, 933, 933C, 939, 939C, 941, 943, 950, 951B, 953, 953C, 955K, 955L,...
5P5630
TUBE-ETHER FITTING TO MANIFOLD (8 DM)
1090, 1190, 1190T, 120B, 120G, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140B, 140G, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14H, ...
1090, 1190, 1190T, 120B, 120G, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 1390, 140B, 140G, 140H, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 143H, 14G, 14H, ...