7E3554 TUBE AS Caterpillar parts
814F, 815F, 816F, 966F, 966F II, 970F
Rating:
Alternative (cross code) number:
CA7E3554
7E-3554
7E3554
CA7E3554
7E-3554
7E3554
Weight: 2 pounds 1 kg.
LANDFILL COMPACTOR, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$41.72
27 Apr 2023
Amazon.com
CTP 7E3554 Tube Fittings for Models 814F/815F/816F/966F/966F II/970F
CTP For Models 814F/815F/816F/966F/966F II/970F || Highly Efficient || Easy in-and-out fit
CTP For Models 814F/815F/816F/966F/966F II/970F || Highly Efficient || Easy in-and-out fit
$33.83
02 Jul 2022
Amazon.com
CTP 7E3554 Tube Fittings for Models 814F/815F/816F/966F/966F II/970F
CTP For Models 814F/815F/816F/966F/966F II/970F || Highly Efficient || Easy in-and-out fit
CTP For Models 814F/815F/816F/966F/966F II/970F || Highly Efficient || Easy in-and-out fit
Compatible equipment models: 7E3554:
Information:
The 3176C engine is an in-line six cylinder engine. The 3176C engine has a bore of 125.0 mm (4.92 inch) and a stroke of 140.0 mm (5.51 inch). The displacement is 10.3 L (629 in3). The engine has a firing order sequence:1, 5, 3, 6, 2 and 4. The rotation of this engine is counterclockwise when the engine is viewed from the flywheel end of the engine. The engine is turbocharged. The electronic unit injector system (EUI) eliminates many of the mechanical components that are traditionally used in the fuel injector assembly. The EUI also provides increased control of the timing and increased control of the fuel air mixture. The timing advance is achieved by precise control of the fuel injection timing. Engine rpm is controlled by adjusting the injection duration. A special pulse wheel provides information to the Electronic Control Module (ECM) for detection of cylinder position and engine rpm.The engine has built-in diagnostics in order to ensure that all of the components are operating properly. In the event of a system component failure, the operator will be alerted to the condition by a "check engine" light. The "check engine" light is located on the operator station. An electronic service tool can be used to read the numerical code of the faulty component or condition. Starting The Engine
The engine's ECM will automatically provide the correct amount of fuel in order to start the engine. Do not activate the throttle while the engine is cranking. If the engine fails to start in 30 seconds, release the starting switch. Allow the starting motor to cool for two minutes before using the starting motor again.
Excessive ether (starting fluid) can cause piston and ring damage. Use ether for cold weather starting purposes only.
Cold Mode Operation
The ECM will set the cold start strategy when the coolant temperature is below 17 °C (63 °F).When the cold start strategy is activated, low idle rpm will be increased to 800 rpm and the engine's power will be limited.Cold mode operation will be deactivated when any of the following conditions have been met:
Coolant temperature reaches 28 °C (82 °F).
The engine has been running for twelve minutes.Cold mode operation varies the fuel injection amount for white smoke cleanup. Cold mode operation also varies the timing for white smoke cleanup. The engine operating temperature is usually reached before the walk-around inspection is completed. The engine will idle at the programmed low idle rpm in order to be put in gear.
Do not operate the engine under a load in the cold mode. While in the cold mode, the low idle will be reduced to the customer programmed low idle and the power will be reduced.
After the cold mode is completed, the engine should be operated at low rpm until normal operating temperature is reached. The engine will reach normal operating temperature faster when the engine is operated at low rpm and low power demand. Typically, the engine should be up to operating temperature within a few minutes. Customer Specified
The engine's ECM will automatically provide the correct amount of fuel in order to start the engine. Do not activate the throttle while the engine is cranking. If the engine fails to start in 30 seconds, release the starting switch. Allow the starting motor to cool for two minutes before using the starting motor again.
Excessive ether (starting fluid) can cause piston and ring damage. Use ether for cold weather starting purposes only.
Cold Mode Operation
The ECM will set the cold start strategy when the coolant temperature is below 17 °C (63 °F).When the cold start strategy is activated, low idle rpm will be increased to 800 rpm and the engine's power will be limited.Cold mode operation will be deactivated when any of the following conditions have been met:
Coolant temperature reaches 28 °C (82 °F).
The engine has been running for twelve minutes.Cold mode operation varies the fuel injection amount for white smoke cleanup. Cold mode operation also varies the timing for white smoke cleanup. The engine operating temperature is usually reached before the walk-around inspection is completed. The engine will idle at the programmed low idle rpm in order to be put in gear.
Do not operate the engine under a load in the cold mode. While in the cold mode, the low idle will be reduced to the customer programmed low idle and the power will be reduced.
After the cold mode is completed, the engine should be operated at low rpm until normal operating temperature is reached. The engine will reach normal operating temperature faster when the engine is operated at low rpm and low power demand. Typically, the engine should be up to operating temperature within a few minutes. Customer Specified
Caterpillar parts catalog:
Parts tube Caterpillar catalog:
8N7315
TUBE AS-OUTLET
120B, 120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 235, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C,...
120B, 120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 235, 235B, 330, 330 L, 3304, 3304B, 3306, 3306B, 3306C,...
1W4785
TUBE AS
14H NA, 3304, 3306B, 814B, 815B, 966D, 966F, 966F II, 970F, 972G, D25D, D300D
14H NA, 3304, 3306B, 814B, 815B, 966D, 966F, 966F II, 970F, 972G, D25D, D300D
8N0449
TUBE AS
12G, 14G, 3304, 3306, 3306B, 621R, 814B, 815B, 966C, 966D, 966F, 966F II, 972G, D25D, D300D
12G, 14G, 3304, 3306, 3306B, 621R, 814B, 815B, 966C, 966D, 966F, 966F II, 972G, D25D, D300D
7N5645
TUBE AS-OUTLET
12G, 14G, 14H NA, 3306, 3306C, 814B, 815B, 966C, 966D, 966F, 966F II, 970F, 972G
12G, 14G, 14H NA, 3306, 3306C, 814B, 815B, 966C, 966D, 966F, 966F II, 970F, 972G
1W4323
TUBE AS
814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 972G
814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 972G
1N2909
TUBE AS-OIL
814B, 815B, 966D, 966F, 966F II, 972G
814B, 815B, 966D, 966F, 966F II, 972G
1N2911
TUBE AS-OIL DRAIN
814B, 815B, 966D, 966F, 966F II, 972G
814B, 815B, 966D, 966F, 966F II, 972G
7E3553
TUBE
814F, 815F, 816F, 966F, 966F II, 970F
814F, 815F, 816F, 966F, 966F II, 970F
4V7697
TUBE AS
814B, 814F, 815B, 815F, 816B, 816F, 966D, 966F, 966F II, 970F
814B, 814F, 815B, 815F, 816B, 816F, 966D, 966F, 966F II, 970F
6W9678
TUBE AS
966D, 966F, 966F II
966D, 966F, 966F II
6W9677
TUBE AS
966D, 966F, 966F II
966D, 966F, 966F II
1384814
TUBE AS
814F, 815F, 816F, 950F, 950F II, 960F, 966F, 966F II, 970F
814F, 815F, 816F, 950F, 950F II, 960F, 966F, 966F II, 970F
7E3553
TUBE
814F, 815F, 816F, 966F, 966F II, 970F
814F, 815F, 816F, 966F, 966F II, 970F
1N2911
TUBE AS-OIL DRAIN
814B, 815B, 966D, 966F, 966F II, 972G
814B, 815B, 966D, 966F, 966F II, 972G
1N2909
TUBE AS-OIL
814B, 815B, 966D, 966F, 966F II, 972G
814B, 815B, 966D, 966F, 966F II, 972G
1W4323
TUBE AS
814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 972G
814F, 815B, 815F, 816F, 966D, 966F, 966F II, 970F, 972G
6C5370
TUBE AS
966F
966F
4E8125
TUBE
844, 988F, 988F II, 990, 990 II, 992D, 994, 994D
844, 988F, 988F II, 990, 990 II, 992D, 994, 994D
6C5299
TUBE AS
966F
966F
4V7697
TUBE AS
814B, 814F, 815B, 815F, 816B, 816F, 966D, 966F, 966F II, 970F
814B, 814F, 815B, 815F, 816B, 816F, 966D, 966F, 966F II, 970F
9V8011
TUBE AS
814B, 815B, 816B, 966D, 966F, 966F II, 970F
814B, 815B, 816B, 966D, 966F, 966F II, 970F
4V7698
TUBE AS
814B, 815B, 816B, 966D, 966F, 966F II, 970F
814B, 815B, 816B, 966D, 966F, 966F II, 970F
6C5501
TUBE AS
966F, 966F II, 972G
966F, 966F II, 972G
4P6590
TUBE AS
966F, 966F II
966F, 966F II