8S0892 TUBE (To Cylinder Head) Caterpillar parts
627, 920, 930, 950, 966C
Rating:
Alternative (cross code) number:
CA8S0892
8S-0892
8S0892
CA8S0892
8S-0892
8S0892
Weight: 0.09 pounds 0 kg.
WHEEL LOADER, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$6.58
13 Nov 2022
Amazon.com
CTP 8S0892 Tube Fittings for Models 627/920/930/950/966C
CTP For Models 627/920/930/950/966C || Highly Efficient || Easy in-and-out fit
CTP For Models 627/920/930/950/966C || Highly Efficient || Easy in-and-out fit
$13.39
08 Jun 2022
US: Florida-Parts-Z
8S0892 - Tube (10.66"" Long-Outlet) fit Caterpillar (CAT)
FIRST PRICE PARTS
FIRST PRICE PARTS
$7.23
08 Jun 2022
Amazon.com
CTP 8S0892 Tube Fittings for Models 627/920/930/950/966C
CTP For Models 627/920/930/950/966C || Highly Efficient || Easy in-and-out fit
CTP For Models 627/920/930/950/966C || Highly Efficient || Easy in-and-out fit
Number on catalog scheme:
2
For full view, you need register
Compatible equipment models: 8S0892:
Information:
Remove & Install Connecting Rod Bearings
Start By:a. remove oil pumpb. remove oil pan plate
3306 Engine Shown1. Turn the crankshaft until two pistons are at the bottom center. Remove connecting rod caps (1) from the two connecting rods. Remove the lower half of the rod bearing from the rod bearing cap.
The connecting rod bolts are loose on the connecting rods and can fall out when the nuts are removed.
2. Push connecting rods (2) away from the crankshaft. Remove the upper half of the rod bearing from the connecting rod. The following steps are for the installation of the connecting rod bearings. Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.
Be sure the tabs in the back of the connecting rod bearings are in the tab grooves of the connecting rod and cap.
3. Install the upper half of the rod bearing in the connecting rod, and put the connecting rod in position on the crankshaft.4. Install the lower half of the rod bearing in the connecting rod cap. For complete details concerning measuring bearing clearances, see Engine Bearings & Crankshafts, SEBD0531.5. Use Plastigage (A) to check the connecting rod bearing clearance.6. Put Plastigage (A) on the connecting rod bearing.7. Put clean engine oil on the threads of the rod bolts and seat surfaces of the nuts.
When connecting rod caps are installed, make sure the number on the side of the cap is next to and respective with the number on the side of the connecting rod.
Do not turn the crankshaft when Plastigage (A) is in position. 8. Install connecting rod cap (1). Install the nuts. Tighten the nuts to a torque of 40 4 N m (30 3 lb ft). Put a mark on each nut and the end of each bolt. Tighten the nuts 90 degrees more. Remove the connecting rod caps. Remove Plastigage (A), and measure the thickness of the Plastigage. The connecting rod clearance must be 0.076 to 0.168 mm (.0030 to .0066 in) for new bearings. The maximum clearance with used bearings is 0.25 mm (.010 in).9. Install the connecting rod caps, and tighten the nuts as in Step 8.10. Do Steps 1 through 9 for the remainder of the connecting rod bearings.End By:a. install oil pan plateb. install oil pump
Start By:a. remove oil pumpb. remove oil pan plate
3306 Engine Shown1. Turn the crankshaft until two pistons are at the bottom center. Remove connecting rod caps (1) from the two connecting rods. Remove the lower half of the rod bearing from the rod bearing cap.
The connecting rod bolts are loose on the connecting rods and can fall out when the nuts are removed.
2. Push connecting rods (2) away from the crankshaft. Remove the upper half of the rod bearing from the connecting rod. The following steps are for the installation of the connecting rod bearings. Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.
Be sure the tabs in the back of the connecting rod bearings are in the tab grooves of the connecting rod and cap.
3. Install the upper half of the rod bearing in the connecting rod, and put the connecting rod in position on the crankshaft.4. Install the lower half of the rod bearing in the connecting rod cap. For complete details concerning measuring bearing clearances, see Engine Bearings & Crankshafts, SEBD0531.5. Use Plastigage (A) to check the connecting rod bearing clearance.6. Put Plastigage (A) on the connecting rod bearing.7. Put clean engine oil on the threads of the rod bolts and seat surfaces of the nuts.
When connecting rod caps are installed, make sure the number on the side of the cap is next to and respective with the number on the side of the connecting rod.
Do not turn the crankshaft when Plastigage (A) is in position. 8. Install connecting rod cap (1). Install the nuts. Tighten the nuts to a torque of 40 4 N m (30 3 lb ft). Put a mark on each nut and the end of each bolt. Tighten the nuts 90 degrees more. Remove the connecting rod caps. Remove Plastigage (A), and measure the thickness of the Plastigage. The connecting rod clearance must be 0.076 to 0.168 mm (.0030 to .0066 in) for new bearings. The maximum clearance with used bearings is 0.25 mm (.010 in).9. Install the connecting rod caps, and tighten the nuts as in Step 8.10. Do Steps 1 through 9 for the remainder of the connecting rod bearings.End By:a. install oil pan plateb. install oil pump
Caterpillar parts catalog:
Parts tube Caterpillar catalog:
941, 950, 951B, D4D, D6C, D6D
920, 930, 930R
920, 930
920, 930, 930R, 992
814, 815, 966C, 966R
6J7214
TUBE ASSEM.
920, 930
920, 930
6K9978
TUBE ASSEM.
930, 930R
930, 930R
5J5627
TUBE ASSEM.
621, 623, 627
621, 623, 627
5J5629
TUBE ASSEM.
621, 623, 627
621, 623, 627
8S3622
TUBE (To Cylinder Block)
920, 930, 950
920, 930, 950
8S4611
TUBE (To Bonnet)
920, 930, 950
920, 930, 950