0R7586 TURBO GP-BASIC Caterpillar parts
Rating:
Alternative (cross code) number:
CA0R7586
0R-7586
0R7586
CA0R7586
0R-7586
0R7586
Weight: 25 pounds 11 kg.
Related part:
1956013
TURBO GP-BASIC
0R7586
R
1956015
TURBO GP-BASIC
0R7586
R
1956016
TURBO GP-BASIC
0R7586
R
1956018
TURBO GP-BASIC
0R7586
R
1956019
TURBO GP-BASIC
0R7586
R
1956020
TURBO GP-BASIC
0R7586
R
1956021
TURBO GP-BASIC
0R7586
R
1956022
TURBO GP-BASIC
0R7586
R
1956023
TURBO GP-BASIC
0R7586
R
1862528
TURBO GP-BASIC
0R7586
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Solarhome New Turbo S200S044 Turbocharger 186-2528 195-6021 0R-7586 478470 Compatible With CAT 3126 Engine
Solarhome Part Name: Turbocharger || Part Number: 478470,169604, 169982,178470,0R7586, 0R-7586, 1862528, 186-2528, 1956013, 195-6013, 1956016, 195-6016, 1956018, 195-6018, 1956019, 195-6019, 1956020, 195-6020, 1956021, 195-6021, 1956022, 195-6022, 1956023, 195-6023, 1956028, 195-6028 || Application Models: Compatible With CAT 3126 Engine || Package Include: 1X Turbocharger,186-2528
Solarhome Part Name: Turbocharger || Part Number: 478470,169604, 169982,178470,0R7586, 0R-7586, 1862528, 186-2528, 1956013, 195-6013, 1956016, 195-6016, 1956018, 195-6018, 1956019, 195-6019, 1956020, 195-6020, 1956021, 195-6021, 1956022, 195-6022, 1956023, 195-6023, 1956028, 195-6028 || Application Models: Compatible With CAT 3126 Engine || Package Include: 1X Turbocharger,186-2528
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6891 Injector Tool Group 1
B 9U-6862 Tapered Brush 1
9U-6863 Small Bore Brush 1
9U-7244 End Brush 1
9U-7237 Brush Extension 1
4C-5552 Large Bore Brush 1
C(1) 221-9778 Puller Stud 1
D(1) 9U-7258 Driver Cap 1
E 4C-9507 Retaining Compound -
(1) Part of the 9U-6891 Injector Tool GroupStart By:
Remove the electronic unit injectors.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g01260353
Illustration 2 g01260345
Install Tooling (A) in electronic unit injector sleeve (1).
Tighten the nut on Tooling (A) until the electronic unit injector sleeve is pulled free of the cylinder head.
Illustration 3 g01260357
Remove O-ring seals (2) and O-ring seal (3) from electronic unit injector sleeve (1). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Use Tooling (B) to clean the bore in the cylinder head for the electronic unit injector sleeve.
Ensure that the electronic unit injector sleeve and the cylinder head bore are completely free of oil, dirt, and sealant debris.
Illustration 4 g01260364
Install new O-ring seals (2) and O-ring seal (3) on electronic unit injector sleeve (1). Note: Do not apply Tooling (E) to the cylinder head surfaces. Apply Tooling (E) on the electronic unit injector sleeve only.
Apply Tooling (E) to the contact surface of electronic unit injector sleeve (1) on the surface that is Marked "X".
Lubricate O-ring seals (2) with clean engine oil.
Illustration 5 g01260372
Install Tooling (C) into the threads of electronic unit injector sleeve (1).
Position Tooling (C) and the electronic unit injector sleeve in the cylinder head. Use care not to damage the O-ring seals on the electronic unit injector sleeve.
Use Tooling (D) and a hammer to install electronic unit injector sleeve (1) in the cylinder head.
Ensure that the electronic unit injector sleeve is properly seated in the cylinder head. The Tooling will "RING" when the electronic unit injector sleeve is fully seated in the bore of the cylinder head.
Remove Tooling (D) and Tooling (C). Use a clean towel and remove excess Tooling (E).
Fill the cooling system with coolant. Refer to Operation and Maintenance, "Refill Capacities" for the cooling system capacity. End By:
Install the electronic unit injectors.
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6891 Injector Tool Group 1
B 9U-6862 Tapered Brush 1
9U-6863 Small Bore Brush 1
9U-7244 End Brush 1
9U-7237 Brush Extension 1
4C-5552 Large Bore Brush 1
C(1) 221-9778 Puller Stud 1
D(1) 9U-7258 Driver Cap 1
E 4C-9507 Retaining Compound -
(1) Part of the 9U-6891 Injector Tool GroupStart By:
Remove the electronic unit injectors.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".
Illustration 1 g01260353
Illustration 2 g01260345
Install Tooling (A) in electronic unit injector sleeve (1).
Tighten the nut on Tooling (A) until the electronic unit injector sleeve is pulled free of the cylinder head.
Illustration 3 g01260357
Remove O-ring seals (2) and O-ring seal (3) from electronic unit injector sleeve (1). Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Use Tooling (B) to clean the bore in the cylinder head for the electronic unit injector sleeve.
Ensure that the electronic unit injector sleeve and the cylinder head bore are completely free of oil, dirt, and sealant debris.
Illustration 4 g01260364
Install new O-ring seals (2) and O-ring seal (3) on electronic unit injector sleeve (1). Note: Do not apply Tooling (E) to the cylinder head surfaces. Apply Tooling (E) on the electronic unit injector sleeve only.
Apply Tooling (E) to the contact surface of electronic unit injector sleeve (1) on the surface that is Marked "X".
Lubricate O-ring seals (2) with clean engine oil.
Illustration 5 g01260372
Install Tooling (C) into the threads of electronic unit injector sleeve (1).
Position Tooling (C) and the electronic unit injector sleeve in the cylinder head. Use care not to damage the O-ring seals on the electronic unit injector sleeve.
Use Tooling (D) and a hammer to install electronic unit injector sleeve (1) in the cylinder head.
Ensure that the electronic unit injector sleeve is properly seated in the cylinder head. The Tooling will "RING" when the electronic unit injector sleeve is fully seated in the bore of the cylinder head.
Remove Tooling (D) and Tooling (C). Use a clean towel and remove excess Tooling (E).
Fill the cooling system with coolant. Refer to Operation and Maintenance, "Refill Capacities" for the cooling system capacity. End By:
Install the electronic unit injectors.
Parts turbo Caterpillar catalog:
Caterpillar
20R3086
TURBO GP-BASIC
Caterpillar
Caterpillar
Caterpillar
Caterpillar
0R7693
TURBO GP-BASIC
Caterpillar
Caterpillar
0R7691
TURBO GP-BASIC
Caterpillar
Caterpillar
10R0487
TURBO GP-BASIC
Caterpillar
Caterpillar
Caterpillar
0R7920
TURBO GP-BASIC
Caterpillar
Caterpillar
0R7911
TURBO GP-BASIC
Caterpillar
Caterpillar
Caterpillar
20R2910
TURBO GP-BASIC
Caterpillar
Caterpillar