10R2622 TURBO GP-BASIC Caterpillar parts
Rating:
Alternative (cross code) number:
CA10R2622
10R-2622
10R2622
CA10R2622
10R-2622
10R2622
Weight: 78 pounds 35 kg.
Related part:
2400003
TURBO GP-BASIC
10R2622
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
GTA5008 Turbo ，Compatible With CAT C15 Engine 732430 732430-5003S 732430-9003 240-0003 2400003 10R2622 10R-2622 732430-0003 Turbocharger
JIANBMEI Enhance power: increase intake volume, improve engine power and torque, accelerate more rapidly || Enhanced acceleration sensation: The power boost brought by the turbocharger makes the vehicle feel more pushed back during acceleration, allowing the driver to experience a strong acceleration experience and enhancing driving pleasure || Strong adaptability: With high-altitude compensation function, it can still maintain good performance in thin air environments || Improve combustion efficiency: increase intake air volume to make fuel combustion more complete, improve fuel utilization, and reduce fuel consumption || compatibility: GTA5008 Turbo ，Compatible With CAT C15 Engine 732430 732430-5003S 732430-9003 240-0003 2400003 10R2622 10R-2622 732430-0003 Turbocharger
JIANBMEI Enhance power: increase intake volume, improve engine power and torque, accelerate more rapidly || Enhanced acceleration sensation: The power boost brought by the turbocharger makes the vehicle feel more pushed back during acceleration, allowing the driver to experience a strong acceleration experience and enhancing driving pleasure || Strong adaptability: With high-altitude compensation function, it can still maintain good performance in thin air environments || Improve combustion efficiency: increase intake air volume to make fuel combustion more complete, improve fuel utilization, and reduce fuel consumption || compatibility: GTA5008 Turbo ，Compatible With CAT C15 Engine 732430 732430-5003S 732430-9003 240-0003 2400003 10R2622 10R-2622 732430-0003 Turbocharger
For full view, you need register
Information:
Machine Stopping
Park on a level surface. If it is necessary to park on a grade, block the tracks securely.Do not engage the parking brake while the machine is moving unless an emergency exists.
1. Apply the service brakes to stop the machine. 2. Move the transmission control into NEUTRAL. 3. Engage the parking brake.4. Lower the dozer blade and all attachments to the ground. Apply slight down pressure.Engine Stopping
Stopping the engine immediately after it has been working under load, can result in overheating and accelerated wear of the engine components.Refer to the following stopping procedure, to allow the engine to cool, and to prevent excessive temperatures in the turbocharger center housing, (if equipped) which could cause oil coking problems.
1. With the machine stopped, run the engine for five minutes at low idle. Stopping the engine immediately after it has been working under load, can result in overheating and accelerated wear of the engine components. 2. Push the governor lever all the way forward to stop the engine. Turn the start switch key to OFF. Remove the key.Leaving the Machine
1. Use the steps and handholds. When dismounting use both hands and face the machine. 2. Inspect the engine compartment for debris. Clean out any debris and paper to avoid a fire.3. To reduce fire hazard remove all flammable debris from front bottom guard through the access doors.4. If the machine is being parked for an extended period, (such as overnight, etc.), turn the battery disconnect switch to OFF and remove the key.5. Install all vandalism protection locks and covers.
Park on a level surface. If it is necessary to park on a grade, block the tracks securely.Do not engage the parking brake while the machine is moving unless an emergency exists.
1. Apply the service brakes to stop the machine. 2. Move the transmission control into NEUTRAL. 3. Engage the parking brake.4. Lower the dozer blade and all attachments to the ground. Apply slight down pressure.Engine Stopping
Stopping the engine immediately after it has been working under load, can result in overheating and accelerated wear of the engine components.Refer to the following stopping procedure, to allow the engine to cool, and to prevent excessive temperatures in the turbocharger center housing, (if equipped) which could cause oil coking problems.
1. With the machine stopped, run the engine for five minutes at low idle. Stopping the engine immediately after it has been working under load, can result in overheating and accelerated wear of the engine components. 2. Push the governor lever all the way forward to stop the engine. Turn the start switch key to OFF. Remove the key.Leaving the Machine
1. Use the steps and handholds. When dismounting use both hands and face the machine. 2. Inspect the engine compartment for debris. Clean out any debris and paper to avoid a fire.3. To reduce fire hazard remove all flammable debris from front bottom guard through the access doors.4. If the machine is being parked for an extended period, (such as overnight, etc.), turn the battery disconnect switch to OFF and remove the key.5. Install all vandalism protection locks and covers.
Parts turbo Caterpillar catalog:
10R1894
TURBO GP-BASIC
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
10R1794
TURBO GP-BASIC
Caterpillar
Caterpillar
Caterpillar
Caterpillar
Caterpillar
20R4008
TURBO GP-BASIC
Caterpillar
Caterpillar
Caterpillar