10R8246 TURBOCHARGER GP Caterpillar parts
3516
Rating:
Alternative (cross code) number:
CA10R8246
10R-8246
10R8246
CA10R8246
10R-8246
10R8246
Weight: 74 pounds 33 kg.
MARINE ENGINE,
Related part:
2994614
TURBO GP-BASIC
10R8246
R
Compatible equipment models: 10R8246:
Information:
Removal Procedure
Start By:
Remove the exhaust sensor lines.
Contact with high pressure fuel may cause personal injury or death. Wait 60 seconds after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Turn the fuel supply to the OFF position.
Disconnect the battery. Refer to Operation and Maintenance Manual, "Battery or Battery Cable - Disconnect".
Remove all components in order to access to the wiring harness.
Illustration 1 g02140798
Loosen clamp assemblies (1) and remove hose (2) .
Illustration 2 g02140852
Disconnect fittings (3) and (7) .
Remove bolts (5) , (6) , and (8) and remove tube assembly (4) .
Remove bolt (9) .
Illustration 3 g02140971
Remove nuts (10) and remove bracket (11) .
Disconnect harness assemblies (12) .
Illustration 4 g02141940
Typical Example
Illustration 5 g02141948
Illustration 6 g02156903
Position harness assembly (13) out of the way with cable straps.
Disconnect tube assembly (16) and remove fitting (15) .Note: Relief valve (14) is a two-piece valve which should not be disassembled.Note: Do not loosen at Location (X) .
Remove relief valve (14) .Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Install relief valve (14) in the reverse order of removal.
Tighten relief valve (14) to a torque of 95 3 N m (70 2 lb ft).
Start By:
Remove the exhaust sensor lines.
Contact with high pressure fuel may cause personal injury or death. Wait 60 seconds after the engine has stopped to allow fuel pressure to purge before any service or repair is performed on the engine fuel lines.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Dispose of all fluids according to local regulations and mandates.
Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
Turn the fuel supply to the OFF position.
Disconnect the battery. Refer to Operation and Maintenance Manual, "Battery or Battery Cable - Disconnect".
Remove all components in order to access to the wiring harness.
Illustration 1 g02140798
Loosen clamp assemblies (1) and remove hose (2) .
Illustration 2 g02140852
Disconnect fittings (3) and (7) .
Remove bolts (5) , (6) , and (8) and remove tube assembly (4) .
Remove bolt (9) .
Illustration 3 g02140971
Remove nuts (10) and remove bracket (11) .
Disconnect harness assemblies (12) .
Illustration 4 g02141940
Typical Example
Illustration 5 g02141948
Illustration 6 g02156903
Position harness assembly (13) out of the way with cable straps.
Disconnect tube assembly (16) and remove fitting (15) .Note: Relief valve (14) is a two-piece valve which should not be disassembled.Note: Do not loosen at Location (X) .
Remove relief valve (14) .Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Install relief valve (14) in the reverse order of removal.
Tighten relief valve (14) to a torque of 95 3 N m (70 2 lb ft).
Caterpillar parts catalog:
Parts turbocharger Caterpillar catalog:
1020294
TURBOCHARGER GP
3512, 3512B, 3516, G3412, G3516
3512, 3512B, 3516, G3412, G3516
1182989
TURBOCHARGER GP
3508, 3512, 3516, PM3516
3508, 3512, 3516, PM3516
1W6551
TURBOCHARGER GP
3508, 3512, 3516
3508, 3512, 3516
4W1226
TURBOCHARGER GP
3412, 3412C, 3512, 3516
3412, 3412C, 3512, 3516
1020297
TURBOCHARGER GP
3512, 3516, PM3512
3512, 3516, PM3512
7W9409
TURBOCHARGER GP
3512, 3516
3512, 3516
1020300
TURBOCHARGER GP
3512, 3516
3512, 3516
1020299
TURBOCHARGER GP
3512, 3516
3512, 3516
4W1148
TURBOCHARGER GP
3412, 3412C, 3516
3412, 3412C, 3516
3179781
TURBOCHARGER GP
C280-16
C280-16
3179780
TURBOCHARGER GP
C280-16
C280-16
3179788
TURBOCHARGER GP
C280-8
C280-8
3179779
TURBOCHARGER GP
3608, C280-8
3608, C280-8
3179783
TURBOCHARGER GP
C280-8
C280-8
3160394
TURBOCHARGER
C6.6
C6.6