2016842 TURBOCHARGER GP Caterpillar parts
3126B
Rating:
Alternative (cross code) number:
CA2016842
201-6842
2016842
CA2016842
201-6842
2016842
Weight: 41 pounds 18 kg.
INDUSTRIAL ENGINE,
Related part:
2016842
TURBO GP-BASIC
10R0010
R
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
$148.76
28 Apr 2022
US: Theodore's
SMC NVKF334-3D-01T 1-Solenoid Process Valve, 1/8 Female BSPT Threaded" Port, 0.14 (A to R) Cv, 0.15 (P to A) Cv
Generic number of solenoids: 1 || operating temperature range: Maximum of +50 C || port type: 1/8 Female BSPT Threaded in || response time: 10 ms || flow coefficient (cv) / flow factor (kv): 0.15 (P to A) Cv, 0.14 (A to R) Cv
Generic number of solenoids: 1 || operating temperature range: Maximum of +50 C || port type: 1/8 Female BSPT Threaded in || response time: 10 ms || flow coefficient (cv) / flow factor (kv): 0.15 (P to A) Cv, 0.14 (A to R) Cv
Number on catalog scheme:
For full view, you need register
Compatible equipment models: 2016842:
Information:
7211 (66X1-up) 7221 (98X1-up) 7231 (17W1-up) 7241 (39E1-up) 7251 (74E1461-up) 7261 (89B114-up)* A replacement drive sleeve for the oil pump can now be installed on the oil pump drive shaft of the marine transmission. See the chart for the replacement sleeve and pin needed according to marine transmission model and serial number.Sleeve Installation
Remove the transmission oil pump. It will also be necessary, according to transmission model, to remove either the transmission oil manifold, or the housing at the end of the pump drive shaft. See the Service Manual for procedure. It will be necessary to drill and ream a dowel hole through the new sleeve before installation. Be careful and do not let any metal particles get inside the transmission during the drilling and reaming procedure.
Always disconnect the starting system and shut off the fuel supply to the engine before doing this procedure.
7211 or 7221 Marine Transmission
(1) Remove the original dowel pin and sleeve from shaft assembly (1). Install new 3N9174 Sleeve (2) all the way in shaft assembly (1) as shown.(2) Use the dimension shown as a reference, the original dowel pin hole (A) as a pilot (guide), and drill a .220"Ø (5.6Ø) hole through both sides of sleeve (2). After the hole is drilled, use a reamer to make the hole in the sleeve larger, to .2427"Ø .0005" (6.165Ø 0.013).(3) Install the new 5N1752 Dowel Pin in hole (A) to fasten sleeve (2) to shaft (1). Install all parts that were removed; see the Service Manual for procedure. Connect the starting system and turn on the fuel supply.7231 or 7241 Marine Transmission
(1) Remove the original dowel pin and sleeve from shaft assembly (1). Install new 1N9280 Sleeve (2) all the way in shaft assembly (1) as shown.(2) Use the original dowel pin hole (A) as a pilot (guide) and drill a .290"Ø (7.4Ø) hole through both sides of sleeve (2). After the hole is drilled, use a reamer to make the hole in the sleeve larger, to .3052"Ø .0003" (7.75Ø .008).(3) Install the new 2N6272 Dowel Pin in hole (A) to fasten sleeve (2) to shaft (1). Install all parts that were removed; see the Service Manual for procedure. Connect the starting system and turn on the fuel supply.7251 or 7261 Marine Transmission
(1) Remove the original dowel pin and pump drive sleeve from the end of the pump drive shaft assembly. (2) On the new 7L5646 Sleeve (1), measure the distance shown from face (A) and make a mark (B) at the exact location of the dimension shown. Use the same procedure and make another mark (C) 180° from the location of mark (B). Marks (B) and (C) must be in alignment with each other.(3) Drill a .290"Ø (7.4Ø) hole at locations (B) and (C). After both holes are drilled, use a reamer to make each hole larger, to a size of .3052"Ø .0003" (7.75Ø .008). (4) Install new sleeve (1). Put the drilled holes at locations (B) and
Remove the transmission oil pump. It will also be necessary, according to transmission model, to remove either the transmission oil manifold, or the housing at the end of the pump drive shaft. See the Service Manual for procedure. It will be necessary to drill and ream a dowel hole through the new sleeve before installation. Be careful and do not let any metal particles get inside the transmission during the drilling and reaming procedure.
Always disconnect the starting system and shut off the fuel supply to the engine before doing this procedure.
7211 or 7221 Marine Transmission
(1) Remove the original dowel pin and sleeve from shaft assembly (1). Install new 3N9174 Sleeve (2) all the way in shaft assembly (1) as shown.(2) Use the dimension shown as a reference, the original dowel pin hole (A) as a pilot (guide), and drill a .220"Ø (5.6Ø) hole through both sides of sleeve (2). After the hole is drilled, use a reamer to make the hole in the sleeve larger, to .2427"Ø .0005" (6.165Ø 0.013).(3) Install the new 5N1752 Dowel Pin in hole (A) to fasten sleeve (2) to shaft (1). Install all parts that were removed; see the Service Manual for procedure. Connect the starting system and turn on the fuel supply.7231 or 7241 Marine Transmission
(1) Remove the original dowel pin and sleeve from shaft assembly (1). Install new 1N9280 Sleeve (2) all the way in shaft assembly (1) as shown.(2) Use the original dowel pin hole (A) as a pilot (guide) and drill a .290"Ø (7.4Ø) hole through both sides of sleeve (2). After the hole is drilled, use a reamer to make the hole in the sleeve larger, to .3052"Ø .0003" (7.75Ø .008).(3) Install the new 2N6272 Dowel Pin in hole (A) to fasten sleeve (2) to shaft (1). Install all parts that were removed; see the Service Manual for procedure. Connect the starting system and turn on the fuel supply.7251 or 7261 Marine Transmission
(1) Remove the original dowel pin and pump drive sleeve from the end of the pump drive shaft assembly. (2) On the new 7L5646 Sleeve (1), measure the distance shown from face (A) and make a mark (B) at the exact location of the dimension shown. Use the same procedure and make another mark (C) 180° from the location of mark (B). Marks (B) and (C) must be in alignment with each other.(3) Drill a .290"Ø (7.4Ø) hole at locations (B) and (C). After both holes are drilled, use a reamer to make each hole larger, to a size of .3052"Ø .0003" (7.75Ø .008). (4) Install new sleeve (1). Put the drilled holes at locations (B) and
Caterpillar SIS machinery equipment:
Parts turbocharger Caterpillar catalog:
3126B, 3126E, AP-1055D, BG-2455D, BG-260D
2423580
TURBOCHARGER GP
3126B, C7, C9
3126B, C7, C9
3126, 3126B, 3126E
2269412
TURBOCHARGER GP
3126B, 3126E, C7
3126B, 3126E, C7
3126B, 3126E, C7
3126B, C7, C9
2016846
TURBOCHARGER GP
3126B, C7, SPP101
3126B, C7, SPP101
3126B, 3126E
2019635
TURBOCHARGER GP
3126B, AP-1055D, BG-2455D, BG-260D, C7, SPP101
3126B, AP-1055D, BG-2455D, BG-260D, C7, SPP101
3126, 3126B, 3126E, C7
1996064
TURBOCHARGER GP
3126B, 3126E
3126B, 3126E
2019634
TURBOCHARGER GP
3126B
3126B
2269413
TURBOCHARGER GP
3126E
3126E
3126, 3126B, 3126E
1292879
TURBOCHARGER GP
345B, 345B L
345B, 345B L
3523459
TURBOCHARGER GP
3512, 3512B, 3512C
3512, 3512B, 3512C
2564500
TURBOCHARGER GP
C175-16
C175-16
1105778
TURBOCHARGER GP
3306, 3306B
3306, 3306B