2347857 TURBOCHARGER GP Caterpillar parts
966H
Rating:
Alternative (cross code) number:
CA2347857
234-7857
2347857
CA2347857
234-7857
2347857
WHEEL LOADER,
Compatible equipment models: 2347857:
Number on catalog scheme:
For full view, you need register
Information:
Parts
Table 1
Parts List
Part Number Description
130-6951 Grease Cartridge
400 g (14 oz)
317-8491 Grease Cartridge (Auto-Lube)
400 g (14 oz) Hammer Inspection
Illustration 1 g03643462
Cross section view of front head (1) Lubrication passage (2) Upper bushing (3) Tool retaining pin (4) Area (trapped hammer paste) (5) Lower bushing upper seal (6) Lower bushing (7) ToolWhen using Auto-Lube, lower bushing (6) can receive less hammer paste compared to upper bushing (2). Increasing the delivery amount on the Auto-Lube to lubricate the lower bushing adequately, fills tool retaining pin area (4) of the front head with excess hammer paste that is now delivered to upper bushing (2).
Illustration 2 g03643535
Excess hammer paste (8) Retaining pin plugExcess hammer paste can eventually cause tool retaining pin plugs (8) to push out and empty the excess hammer paste from the front head.Adjust Lubrication Delivery
Inspect hammer paste delivery method.If Auto-Lube is used, check for correct settings and adjust if necessary.If hammer paste is applied manually, 15-20 pumps per bushing every 2 hours is recommended.Excessive hammer paste can over-fill tool retaining pin area (4) in the front head. Exhausted hammer paste from upper bushing (1) can accumulate in tool retaining pin area (4) in the front head if tool is not removed as recommended.Tool (7) should be removed every 50 service hours or once per week, whichever comes first. Tool should be removed for tool, bushing, and retainer pin inspection and maintenance. During this process, the exhausted hammer paste that has accumulated can be removed from the hammer.
Illustration 3 g03643570
Bottom view of hammer (6) Lower bushing (7) Tool (9) Hammer paste (10) Wiper sealDuring operation of the hammer, the immediate area below lower bushing wiper seal (10) on tool (7) should always have a thin layer of fresh hammer paste. If this area is dry, the lower bushing is not receiving enough hammer paste and the lubrication delivery methods should be inspected and adjusted.
Illustration 4 g03643572
Bottom view of hammer (9) Hammer paste
Table 1
Parts List
Part Number Description
130-6951 Grease Cartridge
400 g (14 oz)
317-8491 Grease Cartridge (Auto-Lube)
400 g (14 oz) Hammer Inspection
Illustration 1 g03643462
Cross section view of front head (1) Lubrication passage (2) Upper bushing (3) Tool retaining pin (4) Area (trapped hammer paste) (5) Lower bushing upper seal (6) Lower bushing (7) ToolWhen using Auto-Lube, lower bushing (6) can receive less hammer paste compared to upper bushing (2). Increasing the delivery amount on the Auto-Lube to lubricate the lower bushing adequately, fills tool retaining pin area (4) of the front head with excess hammer paste that is now delivered to upper bushing (2).
Illustration 2 g03643535
Excess hammer paste (8) Retaining pin plugExcess hammer paste can eventually cause tool retaining pin plugs (8) to push out and empty the excess hammer paste from the front head.Adjust Lubrication Delivery
Inspect hammer paste delivery method.If Auto-Lube is used, check for correct settings and adjust if necessary.If hammer paste is applied manually, 15-20 pumps per bushing every 2 hours is recommended.Excessive hammer paste can over-fill tool retaining pin area (4) in the front head. Exhausted hammer paste from upper bushing (1) can accumulate in tool retaining pin area (4) in the front head if tool is not removed as recommended.Tool (7) should be removed every 50 service hours or once per week, whichever comes first. Tool should be removed for tool, bushing, and retainer pin inspection and maintenance. During this process, the exhausted hammer paste that has accumulated can be removed from the hammer.
Illustration 3 g03643570
Bottom view of hammer (6) Lower bushing (7) Tool (9) Hammer paste (10) Wiper sealDuring operation of the hammer, the immediate area below lower bushing wiper seal (10) on tool (7) should always have a thin layer of fresh hammer paste. If this area is dry, the lower bushing is not receiving enough hammer paste and the lubrication delivery methods should be inspected and adjusted.
Illustration 4 g03643572
Bottom view of hammer (9) Hammer paste
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts turbocharger Caterpillar catalog:
1220350
TURBOCHARGER GP
3608, 3616
3608, 3616
4P7015
TURBOCHARGER GP
3608, 3616
3608, 3616
3044C, C3.4
3006610
TURBOCHARGER GP
3044C
3044C