TURBOCHARGER GP 2558862 - Caterpillar

2558862 TURBOCHARGER GP Caterpillar parts 725, 730

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2558862
255-8862
2558862

Weight: 59 pounds 26 kg.

Buy TURBOCHARGER GP 2558862 Caterpillar genuine, new aftermarket tractor parts with delivery
ARTICULATED TRUCK, EJECTOR TRUCK,

Related part:

2558862 TURBO GP-BASIC 10R8970 R

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

Lirufeng GTA4502BS turbocharger 762548-5004S For Caterpillar Truck, Industrial C13 Engine 2003-247-2964, 2472964, 331-5888, 3315888, 255-8862, 2558862, 2751294, 10R7297

$1,506.00

09 Oct 2025

CN: Lirufeng

Lirufeng GTA4502BS turbocharger 762548-5004S For Caterpillar Truck, Industrial C13 Engine 2003-247-2964, 2472964, 331-5888, 3315888, 255-8862, 2558862, 2751294, 10R7297
lirufeng one year warranty. || Part Number:762548-5004S Previous Part Number:762548-0004, 762548-9004, 762548-0008, 762548-4, 762548-8 OE Number:247-2964, 2472964, 331-5888, 3315888, 255-8862, 2558862, 2751294, 10R7297 Year:2003- Description:Industrial Engine, CLAAS Lexion 570, Petroleum Products,truck CHRA:712402-0038 (712402-5038S)(274-7104, 2747104) || Turbo Model:GTA4502S, GTA4502BS Engine Manufacturer:Caterpillar Displacement:13.0L, 12500 ccm, 6L Cylinders Fuel:Diesel KW:441 HP Industrial Engine:C13 Petroleum Products:C13, CX31-C13I, TH35-C13I, CX31-P600, TH35-E81 Truck Engine:C13 S/N:LGK878-UP Bearing Housing:712342-0015 Turbine Wheel:729838-0002 (Ind. 70.87 mm, Exd. 80.9 mm, 14 Blades) Comp. Wheel:735657-0011/722356-0010 (Ind. 87.28 mm, Exd. 102.38 mm, Trm 20.83, 7+7 Blades) || Back plate:712339-0001/712339-0002 Heat shield Number:410366-0007 (7C7058)(410366-0003, 410366-0004) Repair Kit:468262-0002 (23514027) (1102045750) Turbine housing:753440-0004 Compressor housing:452616-0042 Actuator:451764-0015 Turbine Housing A/R1.33 || Gasket oil inlet:129119 (210019, 201049, 9737, 1S6595, 210019-0000, 409266-0003, 3819900, 129120)(417378 Replaced by 420641)(1900000035) Gasket (oil outlet):210060 (311585, 148062, 2475013) (Paper) Applications: 2003- Caterpillar Truck, Industrial C13 Engine

06 Oct 2025

Turbocharger GT4502BS 2472964 762550-5003S 762550-0003 762550-0001 2558862 Compatible With turbo charger Caterpillar Earth Moving C13

$1,660.23

02 Sep 2025

CN: XuZhen198

Turbocharger GT4502BS 2472964 762550-5003S 762550-0003 762550-0001 2558862 Compatible With turbo charger Caterpillar Earth Moving C13
JFHJGUER Easy installation || Wide compatibility || Enhanced fuel efficiency || Compact and lightweight || Improved response speed

Number on catalog scheme: 3

Caterpillar 2558862 Parts scheme TURBOCHARGER GP

For full view, you need register

Compatible equipment models: 2558862:

ARTICULATED TRUCK 725 730

EJECTOR TRUCK Caterpillar

Information:

Illustration 1 g00919575
Schematic of the Air Pressure Sensor for the Tractor
This diagnostic code is associated with the Air Pressure Sensor for the Tractor. The FMI 03 means that the ECM has determined that the voltage of the circuit for the sensor is above normal.This sensor is an input to the ECM that produces a 5 kHz pulse width modulated signal.The possible causes of this diagnostic code are listed below:
The signal circuit for the sensor is open.
The signal circuit for the sensor is shorted to the +battery circuit.
The sensor has failed.
The power circuit or the ground circuit has failed.
The ECM has failed. This is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear the diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1429 FMI 03 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:The diagnostic code of CID 1429 FMI 03 will be logged in the internal memory of the Transmission/Chassis ECM.The sensors air pressure is ignored when determining if all air pressures are above the Brakes release point and/or the Brakes engage point. When this diagnostic code occurs, a warning (Category 1) is shown on the monitor.Test Step 1. CHECK FOR POWER AT THE SENSOR.
Do not disconnect the harness connector from the sensor.
Turn the key start switch and the disconnect switch to the ON position.
At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along the voltage supply wire (contact A).
Measure the voltage from contact A to frame ground. Expected Result:The voltage is 24 DCV.Results:
OK - The voltage is 24 DCV. Proceed to Test Step 2.
NOT OK - The voltage is not 24 DCV. The + battery circuit in the machine harness has failed.Repair: Replace the machine harness or repair the machine harness.STOPTest Step 2. CHECK FOR PROPER GROUND AT THE SENSOR.
The machine harness remains connected to the sensor.
Turn the key start switch and the disconnect switch to the OFF position.
Remove the 7X-1710 Multimeter Probe from the voltage supply wire (contact A).
At the back of the harness connector for the sensor, insert a 7X-1710 Multimeter Probe along the ground wire (contact B).
Measure the resistance from contact B to frame ground. Expected Result:The resistance is less than 5 ohms.Results:
OK - The resistance is less than 5 ohms. The ground circuit is correct. Proceed to Test Step 3.
NOT OK - The resistance is greater than 5 ohms. The ground circuit in the machine harness has failed.Repair: Replace the machine harness or repair the machine harness.STOPTest Step 3. CHECK THE WIRING HARNESS OF THE SENSOR FOR AN OPEN CIRCUIT.
The key start switch and the disconnect switch remain in the OFF position.
Disconnect the machine harness from the sensor.
At the harness connector for the sensor, connect a jumper wire between contact B and contact C.
Disconnect the machine harness connector(s) from the ECM.
At the harness connector for the ECM, measure