2627609 TURBOCHARGER GP Caterpillar parts
C9
Rating:
Alternative (cross code) number:
CA2627609
262-7609
2627609
CA2627609
262-7609
2627609
Weight: 79 pounds 36 kg.
MARINE ENGINE,
Related part:
2627609
TURBO GP-BASIC
10R3430
R
This part in 10 request:
Show.
This information for suppliers only!
2025-07-28
2023-08-02
2022-10-21
2022-10-18
2021-07-21
2021-06-10
2021-05-26
2019-06-03
2019-05-10
2019-02-12
Compatible equipment models: 2627609:
Information:
Note: A New specification is the performance that can be expected for a new machine. Performance beyond the Service Limit is an indication of these problems: improper maintenance or adjustment, component wear and failure.Introduction
The following test is used to measure engine speed at the flywheel housing.Required Tools
Illustration 1 g02535237
Tooling (C)
Illustration 2 g03261789
Table 2
Required Tools
Tooling Item Part
Number Description QTY
C 348-5430 Multi-Tool Gp
C1 285-0908 Multi-Tool 1
C2 6V-2198 Cable As 1
C3 9U-5140 Photo Pickup 1
C4 6V-3137 Base 1
C5 1U-6605 Reflective Tape 1
C6 6V-3138 Extension 1
D 418-3610 Track Block 2 Reference: Refer to Tool Operating Manual, NEHS1087 for operating instructions for the 348-5430 Multi-Tool Gp.Note: Use Software License Card, NETG5049 with part number 348-5430 Multi-Tool Gp.Machine Preparation
Position the machine on level ground.
Stop the engine.
Install tooling (C) on the engine.
Place track block (D) in the left travel sprocket in order to block left forward travel. Place track block (D) in the right travel sprocket in order to block right forward travel. Test Procedure
Start the engine.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Read the engine speed display (rpm) on the multi-tool. Refer to Table 1 for the specifications for engine speed at the desired engine operation. Travel Procedure
Use the following procedure to check the desired engine speed for travel operation.
Start the engine.
Place the hydraulic activation control lever in the UNLOCK position.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Place the machine controls at the following settings: engine speed dial 10 and AEC switch OFF.
Place the travel speed control switch in HIGH position.
Move both travel levers to the full forward travel position and hold for 10 seconds. Read the engine speed display (rpm) on the multi-tool. The engine speed should slowly increase to 1790 50 rpm.
Return the travel levers to the NEUTRAL position.
The following test is used to measure engine speed at the flywheel housing.Required Tools
Illustration 1 g02535237
Tooling (C)
Illustration 2 g03261789
Table 2
Required Tools
Tooling Item Part
Number Description QTY
C 348-5430 Multi-Tool Gp
C1 285-0908 Multi-Tool 1
C2 6V-2198 Cable As 1
C3 9U-5140 Photo Pickup 1
C4 6V-3137 Base 1
C5 1U-6605 Reflective Tape 1
C6 6V-3138 Extension 1
D 418-3610 Track Block 2 Reference: Refer to Tool Operating Manual, NEHS1087 for operating instructions for the 348-5430 Multi-Tool Gp.Note: Use Software License Card, NETG5049 with part number 348-5430 Multi-Tool Gp.Machine Preparation
Position the machine on level ground.
Stop the engine.
Install tooling (C) on the engine.
Place track block (D) in the left travel sprocket in order to block left forward travel. Place track block (D) in the right travel sprocket in order to block right forward travel. Test Procedure
Start the engine.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Read the engine speed display (rpm) on the multi-tool. Refer to Table 1 for the specifications for engine speed at the desired engine operation. Travel Procedure
Use the following procedure to check the desired engine speed for travel operation.
Start the engine.
Place the hydraulic activation control lever in the UNLOCK position.
Increase the hydraulic oil temperature to 55° 5°C (131° 9°F).
Place the machine controls at the following settings: engine speed dial 10 and AEC switch OFF.
Place the travel speed control switch in HIGH position.
Move both travel levers to the full forward travel position and hold for 10 seconds. Read the engine speed display (rpm) on the multi-tool. The engine speed should slowly increase to 1790 50 rpm.
Return the travel levers to the NEUTRAL position.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts turbocharger Caterpillar catalog:
2507700
TURBOCHARGER GP
2290, 2390, 2391, 2491, 2590, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, C9, CX31-C9I...
2290, 2390, 2391, 2491, 2590, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, C9, CX31-C9I...
2588337
TURBOCHARGER GP
2290, 2390, 2391, 2491, 2590, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, C9, CX31-C9I...
2290, 2390, 2391, 2491, 2590, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 511, 521, 521B, 522, 522B, 532, 541, 541 2, 551, 552, 552 2, C9, CX31-C9I...
2537325
TURBOCHARGER GP
C9, CX31-C9I, TH31-E61
C9, CX31-C9I, TH31-E61
2480323
TURBOCHARGER GP
C9, CX31-C9I, TH31-E61
C9, CX31-C9I, TH31-E61
2507701
TURBOCHARGER GP
C9, CX31-C9I, TH31-E61
C9, CX31-C9I, TH31-E61
2537324
TURBOCHARGER GP
C9, CX31-C9I, TH31-E61
C9, CX31-C9I, TH31-E61
2561201
TURBOCHARGER GP
C9, CX31-C9I, TH31-E61
C9, CX31-C9I, TH31-E61
2561380
TURBOCHARGER GP
C9, CX31-C9I, TH31-E61
C9, CX31-C9I, TH31-E61
3584923
TURBOCHARGER GP
C9, TH31-E61
C9, TH31-E61
3584924
TURBOCHARGER GP
586C, C9, TH31-E61
586C, C9, TH31-E61
2660198
TURBOCHARGER GP
657E, 657G
657E, 657G
3323936
TURBOCHARGER GP
365C, 365C L, 365C L MH, 374D L
365C, 365C L, 365C L MH, 374D L
2654538
TURBOCHARGER GP
385C, 385C FS, 385C L, 385C L MH
385C, 385C FS, 385C L, 385C L MH
2502334
TURBOCHARGER GP
140M, 160M
140M, 160M