AVSPARE.COM
parts catalog

TURBOCHARGER GP 3236356 - Caterpillar



3236356 TURBOCHARGER GP Caterpillar parts D10N TURBOCHARGER
Rating:
19
Alternative (cross code) number:
CA3236356
323-6356
3236356
Caterpillar 3236356 TURBOCHARGER GP
Weight: 55 pounds 24 kg.

Buy TURBOCHARGER GP 3236356 Caterpillar genuine, new aftermarket tractor parts with delivery
TRACK-TYPE TRACTOR,

Compatible equipment models: 3236356:

TRACK-TYPE TRACTOR  D10N   Caterpillar
Number on catalog scheme: 5
 
  For full view, you need register

Information:


Install bolts (27) in order to install drawbar (1) . Tighten bolts (27) to a torque of 540 25 N m (398 18 lb ft).
Illustration 9 g01347282
Start the engine. Extend blade lift cylinders (26) .
Stop the engine and release the system pressure. Refer to Operation and Maintenance Manual, "System Pressure - Release".
Apply Tooling (D) onto inserts (25) . Install inserts (25) , shims (24) , cap (23) , and bolts (22) . Repeat this step for the remaining blade lift cylinder.
Illustration 10 g01347273
Install centershift cylinder (20) . Refer to Disassembly and Assembly, "Centershift Cylinder - Remove and Install". Install clip (21) .
Illustration 11 g01347267
Install wear pad (19) , shoe (18) , and bolts (17) . Tighten adjusting bolts (16) . Repeat this step for the remaining shoes (18) .
Illustration 12 g01347554
Illustration 13 g01347259
Install wear pads (15) , plates (14) , and shims (13) . Repeat this step for the opposite side of the circle.
Illustration 14 g01347254
Install plates (12) and bolts (11) . Repeat this step for the opposite side of the circle.
Stop the engine and release the system pressure. Refer to Operation and Maintenance Manual, "System Pressure - Release".
Illustration 15 g01347614
Illustration 16 g01347615
Measure Dimension (A) between wear pad (15) and circle (3) . Dimension (A) must be no greater than 0.50 mm (0.020 inch). Add or remove shims (13) in order to obtain the correct dimension.
Loosen adjusting bolts (16) and bolts (17) in order to allow movement in shoes (18) . Seat the circle drive pinion in the teeth on circle (3) . Move circle (3) in order to obtain Dimension (C) with circle (3) in contact with front shoes. Dimension (C) must be 60 + 2.50 - 0.50 mm (2.4 + 0.098 - 0.020 inch).
Evenly tighten adjusting bolts (16) against shoes (18) in order to bring wear pads (19) in contact with circle (3) . Back off adjusting bolts (16) in order to obtain Dimension (B) . Dimension (B) must be no greater than 0.80 mm (0.032 inch).
Tighten bolts (17) to 920 60 N m (679 44 lb ft). Tighten nuts (16) to 570 80 N m (421 59 lb ft).
Start the engine and run the engine. Rotate circle (3) through the entire working range and check for binding. Circle (3) must rotate freely.
Stop the engine and release the system pressure. Refer to Operation and Maintenance Manual, "system pressure - Release".
Illustration 17 g01347247
Install clamps (10) . Repeat this step for the opposite side of the drawbar.
Illustration 18 g01347243
Use Tooling (B) and a suitable lifting device in order to raise swivel (8) . The weight of swivel (8) is approximately 41 kg (90 lb).
Install bolts (9) .
Illustration 19 g01347235
Connect hose assemblies (7) . Connect hose assemblies (6) . Install bolt (5) . Connect hose assemblies (4) .
Illustration 20 g01347207
Start the engine. Raise drawbar (1) in order to remove the suitable blocking from blade (2) and remove Tooling (A) from circle (3) . Move drawbar (1) to the center of the machine and lower the blade to the ground.
Stop the engine.

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
C27 Engine Emissions Retrofit Repower Tier III For D10N Tractor 2YD00001-UP (MACHINE)


Parts turbocharger Caterpillar catalog:

1279813 TURBOCHARGER GP
651E, 657E, D10N, D10R, D9L
1644610 TURBOCHARGER GP
651E, 657E, D10N, D10R, D9L
1741471 TURBOCHARGER GP
621G, 623G, 627F, 627G, 657B, 980G II, D10N, D10R, R2900G
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.