3887448 TURBOCHARGER GP Caterpillar parts
308E, 308E CR, 308E SR
Rating:
Alternative (cross code) number:
CA3887448
388-7448
3887448
CA3887448
388-7448
3887448
Weight: 6 pounds 2 kg.
MINI HYD EXCAVATOR,
This part in 4 request:
Show.
This information for suppliers only!
2025-05-30
2025-01-17
2024-07-09
2016-11-17
Information:
Installation Procedure
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     138-7573     Lifting Bracket     2    
B     -     Guide Stud5/8 - 18 NF by 8 inch     2    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01091705
Note: Ring gear (3) must be installed with the chamfered side of the teeth upward. The chamfered side of the gear teeth will be facing toward the starting motor when the flywheel is installed.
Raise the temperature of ring gear (3). Install ring gear (3) on flywheel (2) .
Illustration 2 g01091639
Install Tooling (B) in the crankshaft.
Attach Tooling (A) and a suitable lifting device to flywheel (2). The weight of flywheel (2) is approximately 65 kg (143 lb). Position the flywheel on the crankshaft.
Apply clean engine oil to the threads of bolts (1) .
Install bolts (1). Remove Tooling (B). Install remaining bolts (1) .
Tighten bolts (1) to a torque of 270 40 N m (200 30 lb ft).
Remove Tooling (A) from the flywheel.
Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect".
Table 1
Required Tools    
Tool    Part Number    Part Description    Qty    
A     138-7573     Lifting Bracket     2    
B     -     Guide Stud5/8 - 18 NF by 8 inch     2    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01091705
Note: Ring gear (3) must be installed with the chamfered side of the teeth upward. The chamfered side of the gear teeth will be facing toward the starting motor when the flywheel is installed.
Raise the temperature of ring gear (3). Install ring gear (3) on flywheel (2) .
Illustration 2 g01091639
Install Tooling (B) in the crankshaft.
Attach Tooling (A) and a suitable lifting device to flywheel (2). The weight of flywheel (2) is approximately 65 kg (143 lb). Position the flywheel on the crankshaft.
Apply clean engine oil to the threads of bolts (1) .
Install bolts (1). Remove Tooling (B). Install remaining bolts (1) .
Tighten bolts (1) to a torque of 270 40 N m (200 30 lb ft).
Remove Tooling (A) from the flywheel.
Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel - Inspect".
Caterpillar parts catalog:
Parts turbocharger Caterpillar catalog:
3879092
TURBOCHARGER GP
308E, 308E CR, 308E SR
308E, 308E CR, 308E SR
3563505
TURBOCHARGER
312E, 312E L
312E, 312E L
3214994
TURBOCHARGER AS
307D, 308D
307D, 308D
2803768
TURBOCHARGER GP
305.5D, 305C CR
305.5D, 305C CR
3036486
TURBOCHARGER GP
303.5C, 304D CR
303.5C, 304D CR
2271027
TURBOCHARGER AS
315C, 318B
315C, 318B
6V0900
TURBOCHARGER INSTALLATION
140B, 365B, 365B II, 814, 815, 816, 966C, 966R, D4E, D6C, D6D, D6D SR, D6E, D7H, D7R
140B, 365B, 365B II, 814, 815, 816, 966C, 966R, D4E, D6C, D6D, D6D SR, D6E, D7H, D7R
4181491
TURBOCHARGER AS
306E, 307E
306E, 307E
3563509
TURBOCHARGER
314E CR, 314E LCR
314E CR, 314E LCR