1786560 U-BOLT Caterpillar parts
320C, 320C FM
Rating:
Alternative (cross code) number:
CA1786560
178-6560
1786560
CA1786560
178-6560
1786560
Weight: 0.82 pounds 0 kg.
Information:
DIAMETER
0
mm
HEIGHT
0
mm
NUMBER OF BENDS
1
THREAD LENGTH
0000040.0000
mm
THREAD SIZE
M10X1.25
WIDTH
0
WIDTH BETWEEN CENTERLINE THREAD
295
EXCAVATOR,
Compare Prices:
As an associate, we earn commssions on qualifying purchases through the links below
CTP 1786560 U-Bolt for Heavy Equipment
CTP U-Bolt Only || Sold in each || Easy in-and-out fit
CTP U-Bolt Only || Sold in each || Easy in-and-out fit
CTP 1786560 U-Bolt for Heavy Equipment
CTP U-Bolt Only || Sold in each || Easy in-and-out fit
CTP U-Bolt Only || Sold in each || Easy in-and-out fit
$16.17
28 Nov 2023
Amazon.com
CTP 1786560 U-Bolt for Heavy Equipment
CTP U-Bolt Only || Sold in each || Easy in-and-out fit
CTP U-Bolt Only || Sold in each || Easy in-and-out fit
Number on catalog scheme:
4
For full view, you need register
Caterpillar parts catalog:
Information:
Installation Procedure
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01253203
Ensure that the O-ring seals are in position on tube assembly (8) and tube (11). Place clean engine oil on the O-ring seals.
Attach a suitable lifting device to engine oil cooler (12). The weight of engine oil cooler (12) on G3508 Engines is approximately 45 kg (100 lb). The weight of engine oil cooler (12) on G3512 Engines is approximately 65 kg (145 lb). The weight of engine oil cooler (12) on G3516 Engines is approximately 78 kg (171 lb). Install tube assembly (8) .
Install engine oil cooler (12) on tube (11). Ensure that tube assembly (8) is in the correct position in the adapter of the engine oil filter housing.
Install bolts (9) .
Install bolts (13) and remove the suitable lifting device.
Connect harness assembly (10) for the detonation sensor.
Illustration 2 g00591629
Place clean engine oil on the O-ring seal on the end of tube (7). Install elbow (6) and tube (7) in the engine oil cooler bonnet. Ensure that the gasket is in place and install the bolts.
Illustration 3 g00591628
Install the gasket and the bolts that hold flange (5) and tube (4) .
Install clamp (1) and the bolts that hold tube (2) on the engine.
Install retainers (3) and the bolts on the ends of tube (2) .
Check the engine oil level in the engine. Add engine oil, if necessary. Refer to Operation and Maintenance Manual, "Engine Oil - Change".
Fill the cooling system to the correct level with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".End By: If necessary, install the tube assembly on the prelubrication oil pump. Refer to Disassembly and Assembly, "Prelubrication Oil Pump - Remove and Install".
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01253203
Ensure that the O-ring seals are in position on tube assembly (8) and tube (11). Place clean engine oil on the O-ring seals.
Attach a suitable lifting device to engine oil cooler (12). The weight of engine oil cooler (12) on G3508 Engines is approximately 45 kg (100 lb). The weight of engine oil cooler (12) on G3512 Engines is approximately 65 kg (145 lb). The weight of engine oil cooler (12) on G3516 Engines is approximately 78 kg (171 lb). Install tube assembly (8) .
Install engine oil cooler (12) on tube (11). Ensure that tube assembly (8) is in the correct position in the adapter of the engine oil filter housing.
Install bolts (9) .
Install bolts (13) and remove the suitable lifting device.
Connect harness assembly (10) for the detonation sensor.
Illustration 2 g00591629
Place clean engine oil on the O-ring seal on the end of tube (7). Install elbow (6) and tube (7) in the engine oil cooler bonnet. Ensure that the gasket is in place and install the bolts.
Illustration 3 g00591628
Install the gasket and the bolts that hold flange (5) and tube (4) .
Install clamp (1) and the bolts that hold tube (2) on the engine.
Install retainers (3) and the bolts on the ends of tube (2) .
Check the engine oil level in the engine. Add engine oil, if necessary. Refer to Operation and Maintenance Manual, "Engine Oil - Change".
Fill the cooling system to the correct level with coolant. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change".End By: If necessary, install the tube assembly on the prelubrication oil pump. Refer to Disassembly and Assembly, "Prelubrication Oil Pump - Remove and Install".
Parts u Caterpillar catalog:
2384C, 2470C, 2484C, 2570C, 2670C, 2864C, 315, 317, 318C, 319C, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D2, 320D2 GC, 320D2 L, 320E, 320E L, 320E LN...
311C, 311D LRR, 311F LRR, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 315C, 315D L, 316E L, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 3...
314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 320 L, 320C, 320D FM RR, 320D LRR, 320D RR, 320E LRR, 320E RR, 320N, 321C, 321D LCR, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325,...
1661212
U-BOLT
550, 550B, 560B, 570, 570B, 580, 580B
550, 550B, 560B, 570, 570B, 580, 580B
320 L, 320B, 322B L, 325, 325 L, 325 LN, 325B, 325B L, EL240B, M325B
322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 325B L, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D MH, 326D L, 328D LCR, 329D, 329D L, 329D LN, 330, 330 FM L, 330 L, 33...
02006635
U-BOLT
TSF-54, TSM-54
TSF-54, TSM-54
4375869
U-BOLT
SAT420, SAT630
SAT420, SAT630
3746038
U-BOLT
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
320D GC, 320D L, 320D2, 320D2 GC, 320D2 L, 323D L, 323D2 L
3746028
U-BOLT
320D GC, 320D L, 323D L
320D GC, 320D L, 323D L
2825661
U-BOLT
320C, 320D, 320D L
320C, 320D, 320D L
320C, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 323D L, 323D LN, 323D SA
1495137
U-BOLT
365B, 365B L, 390F L, 533
365B, 365B L, 390F L, 533