AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

D353 ENGINE 46B00001-00598 BASIC ENGINE Caterpillar SIS



INDUSTRIAL ENGINE D353E INDUSTRIAL ENGINE 46B
 D353 ENGINE 46B00001-00598 UE032573 D353E 46B   (1957)

Parts group D353E:

  For full view, you need register
BASIC ENGINE
CAMSHAFT GP
CAMSHAFT GP
4H-9984 CAMSHAFT GP
4H9984 CAMSHAFT GROUP
GEAR GP-IDLER
6H-6580 GEAR GP-IDLER
CAMSHAFT AND POWER TAKE--OFF IDLER GEAR (6H6580 N/S)
CLUTCH GP
TORQUE CONVERTER ASSEMBLY
2L-7602 TORQUE CONVERTER ASSEMBLY
2L7602 TORQUE CONVERTER ASSEMBLY--Side View--Part 1 of 2--Type 1
For use without Cut-Off Clutch
TORQUE CONVERTER ASSEMBLY
2L-7602 TORQUE CONVERTER ASSEMBLY
2L7602 TORQUE CONVERTER ASSEMBLY--Rear View--Part 2 of 2--Type 1
For use without Cut-Off Clutch
TORQUE CONVERTER ASSEMBLY
2L-7602 TORQUE CONVERTER ASSEMBLY
2L7602 TORQUE CONVERTER ASSEMBLY--Side View Part 1 of 2 Type 2
Specification No. 93484. For use without Cut-Off Clutch
TORQUE CONVERTER ASSEMBLY
2L-7602 TORQUE CONVERTER ASSEMBLY
2L7602 TORQUE CONVERTER ASSEMBLY--Rear View--Part 2 of 2 Type 2
Specification No. 93484. FOR USE WITHOUT CUT-OFF CLUTCH
TORQUE CONVERTER ASSEMBLY
2L-7602 TORQUE CONVERTER ASSEMBLY
2L7602 TORQUE CONVERTER ASSEMBLY--Side View Part 1 of 2 Type 3
Specification No. 93484. For use without Cut-Off Clutch
TORQUE CONVERTER ASSEMBLY
2L-7602 TORQUE CONVERTER ASSEMBLY
2L7602 TORQUE CONVERTER ASSEMBLY--Rear View Part 2 of 2 Type 3
Specification No. 93484. FOR USE WITHOUT CUT-OFF CLUTCH
TORQUE CONVERTER ASSEMBLY
3L-1524 TORQUE CONVERTER ASSEMBLY
3L1524 TORQUE CONVERTER ASSEMBLY--Part 1 of 3
For use with Cut-Off Clutch
ADDITIONAL PARTS ARE SHOWN ON PAGES 141 AND 142
TORQUE CONVERTER ASSEMBLY
3L-1524 TORQUE CONVERTER ASSEMBLY
3L1524 TORQUE CONVERTER ASSEMBLY--Part 2 of 3
For use with Cut-Off Clutch
ADDITIONAL PARTS ARE SHOWN ON PAGES 140 AND 142
TORQUE CONVERTER ASSEMBLY
3L-1524 TORQUE CONVERTER ASSEMBLY
3L1524 TORQUE CONVERTER ASSEMBLY--Part 3 of 3
For use with Cut-Off Clutch
ADDITIONAL PARTS ARE SHOWN ON PAGES 140 AND 141
TORQUE CONVERTER FLUID CHARGING GROUP
3L-2040 TORQUE CONVERTER FLUID CHARGING GROUP
3L2040 TORQUE CONVERTER FLUID CHARGING GROUP
TORQUE CONVERTER OUTPUT SHAFT GOVERNOR GROUP
2L-9816 TORQUE CONVERTER OUTPUT SHAFT GOVERNOR GROUP
2L9816 TORQUE CONVERTER OUTPUT SHAFT GOVERNOR GROUP
2H7885 and 3L4022 Governor parts are shown on Pages 146C and 147
TORQUE CONVERTER OUTPUT SHAFT GOVERNOR GROUP
3L-4051 TORQUE CONVERTER OUTPUT SHAFT GOVERNOR GROUP
3L4051 TORQUE CONVERTER OUTPUT SHAFT GOVERNOR GROUP
3L4021 Governor Assembly parts are shown on Page 146B
GOVERNOR ASSEMBLY
3L-4021 GOVERNOR ASSEMBLY
3L4021 GOVERNOR ASSEMBLY
Part of 3L4051 Torque Converter Output Shaft Governor Group shown on Page 146A
TORQUE CONVERTER OUTPUT SHAFT GOVERNOR
2H-7885 TORQUE CONVERTER OUTPUT SHAFT GOVERNOR
2H7885 TORQUE CONVERTER OUTPUT SHAFT GOVERNOR
Part of 2L9816 Torque Converter Output Shaft Governor Group shown on Page 146
Only separate parts serviced. When complete Governor is required order 3L4022 shown on Page 147
GOVERNOR AS-RH
3L-4022 GOVERNOR AS-RH
3L4022 GOVERNOR ASSEMBLY--R.H.
Part of 2L9816 Torque Converter Output Shaft Governor Group shown on Page 146
OUTPUT SHAFT GOVERNOR DRIVE GROUP
2L-9793 OUTPUT SHAFT GOVERNOR DRIVE GROUP
2L9793 OUTPUT SHAFT GOVERNOR DRIVE GROUP
SUPPORTED CLUTCH GROUP
2L-9977 SUPPORTED CLUTCH GROUP
2L9977 SUPPORTED CLUTCH GROUP
ENCLOSED CLUTCH GROUP
2L-7247 ENCLOSED CLUTCH GROUP
2L7247 ENCLOSED CLUTCH GROUP
Part of 2L9977 Supported Clutch Group
FLYWHEEL CLUTCH ASSEMBLY
2L-7163 FLYWHEEL CLUTCH ASSEMBLY
2L7163 FLYWHEEL CLUTCH ASSEMBLY--Type 1
SPECIFICATION NO. 26098
PART OF 2L7247 AND 2L9976 CLUTCH GROUPS ON PAGES 150 AND 152
FLYWHEEL CLUTCH ASSEMBLY
2L-7163 FLYWHEEL CLUTCH ASSEMBLY
2L7163 FLYWHEEL CLUTCH ASSEMBLY--TYPE 2
SPECIFICATION NO. 26474
PART OF 2L7247 AND 2L9976 CLUTCH GROUPS SHOWN ON PAGES 150 AND 152
FLYWHEEL CLUTCH ASSEMBLY
2L-7163 FLYWHEEL CLUTCH ASSEMBLY
2L7163 FLYWHEEL CLUTCH ASSEMBLY--TYPE 3
SPECIFICATION NO. 27771
PART OF 2L7247 AND 2L9976 CLUTCH GROUPS SHOWN ON PAGES 150 AND 152
CLUTCH AND PILLOW BLOCK GROUP
2L-9976 CLUTCH AND PILLOW BLOCK GROUP
2L9976 CLUTCH AND PILLOW BLOCK GROUP
For use with Extended Shaft
2L7163 Flywheel Clutch Assembly parts are shown on Page 151
PILLOW BLOCK
6F-7236 PILLOW BLOCK
6F7236 PILLOW BLOCK (Ball and Socket Type)
Part of 2L9976 Clutch and Pillow Block Group
COUPLING GP
FLEXIBLE COUPLING GROUP
9F-7459 FLEXIBLE COUPLING GROUP
9F7459 FLEXIBLE COUPLING GROUP
Part of 2L9463 Generator Installation Group
GENERATOR DRIVE COUPLING GROUP
2L-9328 GENERATOR DRIVE COUPLING GROUP
2L9328 GENERATOR DRIVE COUPLING GROUP
Part of 2L9321 Generator Installation Group
CRANKSHAFT GP
CRANKSHAFT
CRANKSHAFT
CRANKSHAFT
CRANKSHAFT BEARING REPLACEMENT GROUPS
CRANKSHAFT BEARING REPLACEMENT GROUPS
CRANKSHAFT BEARING REPLACEMENT GROUPS
CYLINDER BLOCK GP
CYLINDER BLOCK AND COVERS
CYLINDER BLOCK AND COVERS
CYLINDER BLOCK AND COVERS--Side View--Part 1 of 2
Serial No. 46B1 to 46B448 inclusive. 4M7000 Block Assembly parts are shown on Page 22
Note: 8H7207 Piston and Liner Group, 9H2815 Cylinder Liner and Piston Replacement Gasket Group and 9H4720 Valve Grinding Gasket
Group are available. Piston and Liner replacement require the use of 9H2815 and 9H4720 Gasket Groups
CYLINDER BLOCK AND COVERS
CYLINDER BLOCK AND COVERS
CYLINDER BLOCK AND COVERS--End View--Part 2 of 2
Serial No. 46B1 to 46B448 inclusive
CYLINDER BLOCK AND COVERS
CYLINDER BLOCK AND COVERS
CYLINDER BLOCK AND COVERS--Side View--Part 1 of 2
Effective with Serial No. 46B449. 4M7000 Block Assembly parts are shown on Page 22
Note: 8H7207 Piston and Liner Group, 9H2815 Cylinder Liner and Piston Replacement Gasket Group and 9H4720 Valve Grinding Gasket
Group are available. Piston and Liner replacement require the use of 9H2815 and 9H4720 Gasket Groups
CYLINDER BLOCK AND COVERS
CYLINDER BLOCK AND COVERS
CYLINDER BLOCK AND COVERS--End View--Part 2 of 2
Serial No. 46B449-Up
CYLINDER BLOCK ASSEMBLY
4M-7000 CYLINDER BLOCK ASSEMBLY
4M7000 CYLINDER BLOCK ASSEMBLY
Part of Cylinder Block and Covers shown on Page 20
CYLINDER HEAD GP
CYLINDER HEAD AND VALVE MECHANISM
CYLINDER HEAD AND VALVE MECHANISM
CYLINDER HEAD AND VALVE MECHANISM--Side View--Part 1 of 2
CYLINDER HEAD AND VALVE MECHANISM
CYLINDER HEAD AND VALVE MECHANISM
CYLINDER HEAD AND VALVE MECHANISM--End View--Part 2 of 2
Refer also to Page 96 for special parts
DAMPER GP
DAMPER GUARD GROUP
2L-7109 DAMPER GUARD GROUP
2L7109 DAMPER GUARD GROUP
For use without Radiator
DRIVE GP-AUXILIARY
AUXILIARY DRIVE GROUP
3L-1131 AUXILIARY DRIVE GROUP
3L1131 AUXILIARY DRIVE GROUP--R.H.--2.438:1 Ratio
FOR USE WITH ATTACHMENTS UP TO 21 H.P.
Only separate parts serviced. When complete group is required order 4L9460
AUXILIARY DRIVE GROUP
3L-1132 AUXILIARY DRIVE GROUP
3L1132 AUXILIARY DRIVE GROUP--L.H.--2:1 Ratio--Type 1
FOR USE WITH ATTACHMENTS UP TO 21 H.P.
FOR USE WITHOUT CENTRIFUGAL SEA OR FRESH WATER PUMP
AUXILIARY DRIVE GROUP
3L-1132 AUXILIARY DRIVE GROUP
3L1132 AUXILIARY DRIVE GROUP--L.H.--2:1 Ratio--Type 2
FOR USE WITH ATTACHMENTS UP TO 21 H.P.
FOR USE WITHOUT CENTRIFUGAL SEA OR FRESH WATER PUMP
AUXILIARY DRIVE GROUP
4L-9460 AUXILIARY DRIVE GROUP
4L9460 AUXILIARY DRIVE GROUP--R.H.--2.438:1 Ratio
FOR USE WITH ATTACHMENTS NOT EXCEEDING 21 H.P.
DRIVE GP-PUMP
FRESH WATER PUMP AND DRIVE GROUP
2L-3415 FRESH WATER PUMP AND DRIVE GROUP
2L3415 FRESH WATER PUMP AND DRIVE GROUP--Type 1
Refer also to Page 53 for special parts
FRESH WATER PUMP AND DRIVE GROUP
2L-3415 FRESH WATER PUMP AND DRIVE GROUP
2L3415 FRESH WATER PUMP AND DRIVE GROUP--Type 2
Refer also to Page 53 for special parts
OIL PUMP DRIVE
OIL PUMP DRIVE
OIL PUMP DRIVE
Serial No. 46B1 to 46B503 inclusive
DRIVE GP-PUMP
5H-1429 DRIVE GP-PUMP
OIL PUMP DRIVE (5H1429 N/S)
Serial No. 46B504-Up
FLYWHEEL GP
FLYWHEEL
FLYWHEEL
FLYWHEEL
TORQUE CONVERTER MOUNTING GROUP
3L-1522 TORQUE CONVERTER MOUNTING GROUP
3L1522 TORQUE CONVERTER MOUNTING GROUP--Type 2
For use with Cut-Off Clutch
TORQUE CONVERTER MOUNTING GROUP
3L-1522 TORQUE CONVERTER MOUNTING GROUP
3L1522 TORQUE CONVERTER MOUNTING GROUP--Type 1
For use with Cut-Off Clutch
TORQUE CONVERTER MOUNTING GROUP
3L-1521 TORQUE CONVERTER MOUNTING GROUP
3L1521 TORQUE CONVERTER MOUNTING GROUP--Type 1
For use without Cut-Off Clutch
TORQUE CONVERTER MOUNTING GROUP
3L-1521 TORQUE CONVERTER MOUNTING GROUP
3L1521 TORQUE CONVERTER MOUNTING GROUP--Type 2
For use without Cut-Off Clutch
FLYWHEEL GUARD GROUP
3L-1489 FLYWHEEL GUARD GROUP
3L1489 FLYWHEEL GUARD GROUP
HOUSING GP-FLYWHEEL
TORQUE CONVERTER MOUNTING GROUP
3L-1522 TORQUE CONVERTER MOUNTING GROUP
3L1522 TORQUE CONVERTER MOUNTING GROUP--Type 2
For use with Cut-Off Clutch
TORQUE CONVERTER MOUNTING GROUP
3L-1522 TORQUE CONVERTER MOUNTING GROUP
3L1522 TORQUE CONVERTER MOUNTING GROUP--Type 1
For use with Cut-Off Clutch
TORQUE CONVERTER MOUNTING GROUP
3L-1521 TORQUE CONVERTER MOUNTING GROUP
3L1521 TORQUE CONVERTER MOUNTING GROUP--Type 1
For use without Cut-Off Clutch
TORQUE CONVERTER MOUNTING GROUP
3L-1521 TORQUE CONVERTER MOUNTING GROUP
3L1521 TORQUE CONVERTER MOUNTING GROUP--Type 2
For use without Cut-Off Clutch
MOUNTING GP-ENGINE
ENGINE SUPPORT
ENGINE SUPPORT
ENGINE SUPPORT
Serial No. 46B1 to 46B448 inclusive
ENGINE SUPPORT
ENGINE SUPPORT
ENGINE SUPPORT
Effective with Serial No. 46B449
PAN GP-OIL
OIL PAN
OIL PAN
OIL PAN
Refer also to Page 155 for special parts
PAN GP-OIL
2L-3513 PAN GP-OIL
2L3513 OIL PAN GROUP
500 hour oil change period, maximum tilt angle of 17 degrees
PISTON & ROD GP
CONNECTING ROD AND PISTON GROUP
8H-6316 CONNECTING ROD AND PISTON GROUP
8H6316 CONNECTING ROD AND PISTON GROUP (6 Groups Required)
SHAFT GP-STUB
FLEXIBLE SHAFTS
FLEXIBLE SHAFTS
FLEXIBLE SHAFTS
FLEXIBLE SHAFTS
FLEXIBLE SHAFTS
FLEXIBLE SHAFTS
FLYWHEEL STUB SHAFT GROUP
3L-0521 FLYWHEEL STUB SHAFT GROUP
3L521 FLYWHEEL STUB SHAFT GROUP
STUB SHAFT GROUP
6L-2693 STUB SHAFT GROUP
6L2693 STUB SHAFT GROUP--Front Mounted
STUB SHAFT GROUP
6L-2697 STUB SHAFT GROUP
6L2697 STUB SHAFT GROUP--Rear Mounted
CRANKSHAFT STUB SHAFT
3L-1805 CRANKSHAFT STUB SHAFT
3L1805 CRANKSHAFT STUB SHAFT--Front
For use without Radiator
VALVE MECHANISM GP
CYLINDER HEAD AND VALVE MECHANISM
CYLINDER HEAD AND VALVE MECHANISM
CYLINDER HEAD AND VALVE MECHANISM--Side View--Part 1 of 2
CYLINDER HEAD AND VALVE MECHANISM
CYLINDER HEAD AND VALVE MECHANISM
CYLINDER HEAD AND VALVE MECHANISM--End View--Part 2 of 2
Refer also to Page 96 for special parts

Information:

(For parts list, see above)

Truck Engine News
A New Special Instruction , "Troubleshooting Compressed Air System Components and Performance" Is Available {1803, 5500}
2002/09/01
Engine News
A New Diagnostic Kit for the Evaluation of Air Compressor Operation is Introduced {1803}
2004/11/01
Special Instruction
Air Compressor Installation Instructions{1803}
Air Compressor Installation Instructions{1803}
Troubleshooting Compressed Air System Components and Performance{1803, 5500}
Troubleshooting Compressed Air System Components and Performance{1803, 5500}
Service Magazine
Sleeve-Type Ring Compressors Can Be Used For Installation Of Pistons From The Bottom Of The Engine{0622}
1978/08/21
A New Special Instruction, REHS1428 , "Troubleshooting Compressed Air System Components and Performance" Is Available {1803, 5500}
2002/09/23
Engine News
Too Much Clearance For Exhaust Valves Can Cause Wear To The Camshaft Lobes And Valve Lifters
1980/01/09
New Camshaft Has Improved Profile (Shape) Of Exhaust Cam To Extend Service Life
1981/01/28
New 8T2998 Lubricant Available
1986/03/01
Correct Installation Of Valve Lifters On The Camshaft Is Very Important To Prevent Failures
1977/05/25
Service Letter-NACD
Certain OR8266 Remanufactured Camshaft Kits For Use In D353 And G353 Engines Need To Be Removed From Parts Stock
Certain OR8266 Remanufactured Camshaft Kits For Use In D353 And G353 Engines Need To Be Removed From Parts Stock
Service Letter-Australia
Service Letter-CFEL
Service Letter-CSARL
Service Letter-Americas
Service Letter-Brazil
Specifications
Camshaft And Timing Gears
D353 INDUSTRIAL & MARINE ENGINES
Camshaft
D353 INDUSTRIAL & MARINE ENGINES
Service Letter-China
Certain OR8266 Remanufactured Camshaft Kits For Use In D353 And G353 Engines Need To Be Removed From Parts Stock
Certain OR8266 Remanufactured Camshaft Kits For Use In D353 And G353 Engines Need To Be Removed From Parts Stock
Service Letter-Asia
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Service Letter-APD
Certain OR8266 Remanufactured Camshaft Kits For Use In D353 And G353 Engines Need To Be Removed From Parts Stock
Certain OR8266 Remanufactured Camshaft Kits For Use In D353 And G353 Engines Need To Be Removed From Parts Stock
Disassembly and Assembly
Camshaft
D353 INDUSTRIAL & MARINE ENGINES
Camshaft Bearings
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Camshaft Has Improved Profile (Shape) Of Exhaust Cam To Extend Service Life{1210}
1981/02/02
New 8T2998 Lubricant Available{0645,1210}
1986/02/17
Correct Installation Of Valve Lifters On The Camshaft Is Very Important To Prevent Failures{1209}
1977/05/16
Too Much Clearance For Exhaust Valves Can Cause Wear To The Camshaft Lobes And Valve Lifters{1105,1210,1209}
1979/12/24
Special Instruction
Installation Of 5N1678 Rear Power Take-Off Clutch Support Group{1007}
Installation Of 5N1678 Rear Power Take-Off Clutch Support Group{1007}
Procedure For Conversion From Oil Lubrication To Grease Lubrication For Rear Power Takeoff Clutches{3055}
Procedure For Conversion From Oil Lubrication To Grease Lubrication For Rear Power Takeoff Clutches{3055}
Specifications
Enclosed Clutches
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Clutches
D353 INDUSTRIAL & MARINE ENGINES
Clutch Drive Spider
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Clutch (PTO) Warranty On Morbark Industries Products Powered By Caterpillar Engines{7758}
1992/07/20
Disassembly and Assembly
Coupling - Install
SR4B Generators
Coupling - Remove
SR4B Generators
Service Magazine
Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}
1979/09/03
Engine News
Improved Ring Seal Used At Rear of Crankshaft
1980/01/09
New Bend Specification For Used Or Field Reground Crankshafts
1980/08/13
Use 6V6035 Hardness Tester On Crankshafts
1982/02/24
Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks
1983/05/25
Crankshaft Failures
1983/11/30
Remanufactured Undersize Crankshafts Are Available
1984/04/11
Why Choose Caterpillar Remanufactured Crankshafts? Because We Offer More ...
1985/09/01
Overlap Joint On Crankshaft Front Seal Ring Prevents Leakage
1978/08/30
Special Instruction
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}
Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Crankshaft Seal And Wear Sleeve Installation{1160, 1161}
Crankshaft Seal And Wear Sleeve Installation{1160, 1161}
Installation Of Seal Groups With Hydrodynamic Grooves In The Seal Lip{1160, 1161}
Installation Of Seal Groups With Hydrodynamic Grooves In The Seal Lip{1160, 1161}
Specifications
Crankshaft
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Crankshaft Main Bearings
D353 INDUSTRIAL & MARINE ENGINES
Crankshaft Front Seal
D353 INDUSTRIAL & MARINE ENGINES
Crankshaft Rear Seal
D353 INDUSTRIAL & MARINE ENGINES
Crankshaft
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Improved Ring Seal Used At Rear Of Crankshaft {1161}
1980/01/07
Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22
Use 6V6035 Hardness Tester On Crankshafts{0651,1202}
1982/02/22
Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/03
New Main And Connecting Rod Bearings Have A Thicker Layer Of Lead-Tin Overlay (Surface Material){1230,1203,1219}
1982/10/11
Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16
Reuse Of Engine Bearings{1230}
1983/05/16
Crankshaft Failures{1202,1230}
1983/11/21
Reuse Of Engine Bearings{1230,1219,1203}
1983/11/21
Remanufactured Undersize Crankshafts Are Available{1202}
1983/11/21
Installing New Copper Bonded Bearings Can Extend Engine Life{1230,1203,1219}
1985/04/29
Remanufactured Crankshafts Are Available In Standard And Two Undersize Dimensions (U.S. and Canada){1202,7754}
1985/11/18
Bearing Failures On Engines Due To Lack Of Lubrication{1230,1219,1203,1202}
1986/09/08
Crankshaft Support Groups Are Available To Measure Bent Crankshafts{0653,1202}
1977/11/07
Main And Connecting Rod Bearing Part Numbers {1203,1219,1230}
1987/01/26
Use New Main Bearings In Replacement Cylinder Blocks{1203,1201}
1978/06/12
Overlap Joint On Crankshaft Front Seal Ring Prevents Leakage{1160,1202}
1978/08/21
Change In Procedure To Check Main Bearing Clearance{1203}
1978/08/28
New Centering Rings For Oversized Main Bearings{0665,1230}
1979/06/04
40 Power Microscope is Available for Inspecting Bearing Journals on Crankshafts {0777, 1202}
2006/01/16
Engine News
Information About The Use Of Earlier Cylinder Heads And Liners With Spacer Plate Cylinder Blocks; List Of Earlier Articles
1979/03/14
New Filler Bands Give A Better Seal Between The Cylinder Liners And Cylinder Block
1979/05/23
New Liner Seat Inserts For Spacer Plate Cylinder Blocks Are Made Of Stainless Steel
1979/09/19
New Cylinder Liner Has Improved Design To Keep Liner Temperatures Lower
1980/02/06
New Liner Seat Insert For No. 1 And No. 4 Cylinders Of D353 Engines
1980/04/30
In The Future, Oversize And Undersize Connecting Rod And Main Bearings Will Have Size Identification Marks In Metric Units
1980/07/09
Correct Installation Of Inserts Necessary During Repairs To Prevent More Counterbore Cracks
1981/04/01
New Piston Ring Assemblies Give Improved Ring And Cylinder Liner Life
1981/04/22
6V4133 Wedge Bracket Makes Cylinder Liner Removal Easier
1981/07/15
New Tools Available For Installation Of Cylinder Liner Seats; Service Tools For Counterboring Tool Group
1982/02/10
New Liner Seat Insert With O-Ring Seal Available
1982/02/10
Inspection Marks On Bearings
1982/05/12
Information Available For The Installation Of Inserts In Cylinder Blocks And Spacer Plates
1982/08/25
New Main And Connecting Rod Bearings Have A Thicker Layer Of Lead-Tin Overlay (Surface Material)
1982/10/20
Use FT1711 Light Table For Cylinder Liner Inspection
1982/12/15
New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip
1982/12/15
Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks
1983/05/25
Substantial Price Reduction For Caterpillar Remanufactured Short Blocks
1985/06/01
Substantial Price Reduction For Caterpillar Remanufactured Short Blocks
1985/08/01
Main And Connecting Rod Bearing Part Numbers
1987/01/01
Improved Cylinder Block With Spacer Plate Used With New Cylinder Heads, Cylinder Head Gaskets, Cylinder Liners And Timing Gear Housing
1977/05/03
Tools To Hone (Machine) Cylinder Liners Are Available To Permit The Use Of Used Cylinder Liners With New Style Pistons
1977/06/29
New Inserts To Repair Cylinder Liner Seats On D353 Engine Blocks
1977/07/13
Use Only The Larger Size Inserts To Make A Repair To Cylinder Block Counterbores For Cylinder Liners
1977/09/28
5P8665 Cylinder Liner Puller Makes Liner Removal Easier And Faster
1978/01/18
New 5P8709 Piston Tool Group For The Alignment Of Piston Cooling Jets
1978/05/03
Use New Tools To Adapt Former Cylinder Heads With Counterbores To Cylinder Blocks With Spacer Plates
1978/05/24
Use New Main Bearings In Replacement Cylinder Blocks
1978/07/05
Change In Procedure To Check Main Bearing Clearance
1978/08/30
Special Instruction
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Installation Of 7N4013 Or 7N6342 Cylinder Block Service Group And 7N4134 Hardware Kit{1201}
Installation Of 7N4013 Or 7N6342 Cylinder Block Service Group And 7N4134 Hardware Kit{1201}
Use Of 5P8595 Honing Tool Group{1216}
Use Of 5P8595 Honing Tool Group{1216}
Installation Of 1W6265, 1W6266 And 1W6267 Insert For Cylinder Liner Seat{1217}
Installation Of 1W6265, 1W6266 And 1W6267 Insert For Cylinder Liner Seat{1217}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Reconditioning Of Cylinder Heads For Use On Spacer Plate Cylinder Blocks{1101}
Reconditioning Of Cylinder Heads For Use On Spacer Plate Cylinder Blocks{1101}
Installation Of 8N6938 Or 8N6939 Inserts{1217}
Installation Of 8N6938 Or 8N6939 Inserts{1217}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Use Of 6V4840 Tool Group To Install Water Ferrules{1201}
Use Of 6V4840 Tool Group To Install Water Ferrules{1201}
Cylinder Block Cleaning Procedure{1201}
Cylinder Block Cleaning Procedure{1201}
Using 5P4175 Boring Tool Group And 5P1618 Tool Arrangement{0672, 1200}
Using 5P4175 Boring Tool Group And 5P1618 Tool Arrangement{0672, 1200}
Specifications
Cylinder Block<BR> (With Spacer Plate)
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Block<BR> (Without Spacer Plate)
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Liner
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Liner Projection<BR> (With Spacer Plate)
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Liner Projection<BR> (Without Spacer Plate)
D353 INDUSTRIAL & MARINE ENGINES
Reuse And Salvage Guidelines
Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}
Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}
Disassembly and Assembly
Piston Cooling Tubes
D353 INDUSTRIAL & MARINE ENGINES
Crankshaft Main Bearings
D353 INDUSTRIAL & MARINE ENGINES
Spacer Plate
D353 INDUSTRIAL & MARINE ENGINES
Camshaft Bearings
D353 INDUSTRIAL & MARINE ENGINES
Cylinders Liners (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Liners (Later)
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Cylinder Liner Has Improved Design To Keep Liner Temperatures Lower{1216}
1980/02/04
New Liner Seat Insert For No. 1 And No. 4 Cylinders Of D353 Engines{1217}
1980/03/31
Correct Installation Of Inserts Necessary During Repairs To Prevent More Counterbore Cracks{1217,1201}
1981/03/09
New Piston Ring Assemblies Give Improved Ring And Cylinder Liner Life{1215,1213}
1981/04/06
Improved Head Gasket Has Larger Fire Ring To Decrease Fretting {1101,1201}
1981/10/26
Use Of A Flex-Hone For Cylinder Liner Reconditioning{0664,0674,1216}
1981/12/21
Improved Head Gasket Has Larger Fire Ring To Decrease Fretting{1101,1201}
1982/01/11
New Tools Available For Installation Of Cylinder Liner Seats; Service Tools For Counterboring Tool Group{0622,1217}
1982/01/25
New Liner Seat Insert With O-Ring Seal Available{1217,1216}
1982/01/25
Use New Special Instruction To Install 5P6595 Insert In Cylinder Liner Seats{1216,0621}
1982/05/03
Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/03
Information Available For The Installation Of Inserts In Cylinder Blocks And Spacer Plates{1217,1201,0664}
1982/07/05
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
Use FT1711 Light Table For Cylinder Liner Inspection {0652,1216}
1982/11/29
New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip {0653,1216,1105}
1982/11/29
Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16
Reuse Of Engine Bearings{1230}
1983/05/16
Reuse Of Engine Bearings{1230,1219,1203}
1983/11/21
Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02
Bearing Failures On Engines Due To Lack Of Lubrication{1230,1219,1203,1202}
1986/09/08
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
Improved Cylinder Block With Spacer Plate Used With New Cylinder Heads, Cylinder Head Gaskets, Cylinder Liners And Timing Gear Housing{1101,1162,1201,1216}
1977/05/02
Improved Keystone Piston Assembly{1214,1216}
1977/05/02
Tools To Hone (Machine) Cylinder Liners Are Available To Permit The Use Of Used Cylinder Liners With New Style Pistons{0664,1214,1216}
1977/07/04
New Inserts To Repair Cylinder Liner Seats On D353 Engine Blocks{1201,1216,1217,0663,0653}
1977/07/11
Use Only The Larger Size Inserts To Make A Repair To Cylinder Block Counterbores For Cylinder Liners{1201,1216,1217}
1977/10/10
Main And Connecting Rod Bearing Part Numbers {1203,1219,1230}
1987/01/26
Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group {0781,1200,1350}
1987/07/20
5P8665 Cylinder Liner Puller Makes Liner Removal Easier And Faster{0621,1216}
1978/01/09
Use New Tools To Adapt Former Cylinder Heads With Counterbores To Cylinder Blocks With Spacer Plates{0600,1100,1101,1201}
1978/05/22
Use New Main Bearings In Replacement Cylinder Blocks{1203,1201}
1978/06/12
New Information On Reusable Cylinder Liners{1216}
1978/06/19
Change In Procedure To Check Main Bearing Clearance{1203}
1978/08/28
Information About The Use Of Earlier Cylinder Heads And Liners With Spacer Plate Cylinder Blocks; List Of Earlier Articles{0600,1101,1162,1201,1216,1221}
1979/03/26
New Filler Bands Give A Better Seal Between The Cylinder Liners And Cylinder Block{1201,1216}
1979/05/14
New Centering Rings For Oversized Main Bearings{0665,1230}
1979/06/04
New Cylinder Head Gasket Has Smaller Diameter Cylinder Openings To Improve Location Of Combustion Seal Ring{1101,1201}
1979/08/13
Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27
New Liner Seat Inserts For Spacer Plate Cylinder Blocks Are Made Of Stainless Steel{1217,1201,0663}
1979/10/01
Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17
Engine News
Information About The Use Of Earlier Cylinder Heads And Liners With Spacer Plate Cylinder Blocks; List Of Earlier Articles
1979/03/14
New Exhaust Valve Has Improved Three-Piece Construction
1979/04/25
New Cylinder Head Gasket Has Smaller Diameter Cylinder Openings To Improve Location Of Combustion Seal Ring
1979/08/22
Too Much Clearance For Exhaust Valves Can Cause Wear To The Camshaft Lobes And Valve Lifters
1980/01/09
New Inlet And Exhaust Valves And Valve Guides Have Tighter Fit To Prevent Corrosion And Guide Wear
1981/04/01
Improved Head Gasket Has Larger Fire Ring To Decrease Fretting
1982/01/20
Use Caution During Replacement Of Damaged Nozzle Adapters Or Precombustion Chambers
1983/01/19
Engine Valve Stem &quot;Use Again&quot; Specifications
1983/03/16
New Water Seals Used In Cylinder Head Groups
1983/08/17
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures
1983/10/26
A New Book &quot;Analyzing Diesel And Natural Gas Engine Valve Failures&quot; Is Available
1985/03/01
Determining The Cause Of Glow Plug Tip Failures
1986/06/01
Valve Lash Adjustment Interval Is Changed
1986/07/01
New Exhaust Valves Are Used In Caterpillar Remanufactured Cylinder Heads
1990/10/01
Exhaust Valve Guides With A Counterbore Are Now Available
1977/01/28
Improved Cylinder Block With Spacer Plate Used With New Cylinder Heads, Cylinder Head Gaskets, Cylinder Liners And Timing Gear Housing
1977/05/03
Correct Installation Of Valve Lifters On The Camshaft Is Very Important To Prevent Failures
1977/05/25
Tolerance Added To Valve Clearance Specifications
1978/01/18
Use Again Specifications For Valve Springs Are Changed
1978/03/01
Use New Tools To Adapt Former Cylinder Heads With Counterbores To Cylinder Blocks With Spacer Plates
1978/05/24
Caterpillar Warranty Claims on Cylinder Head Valves {1105}
2005/10/03
Special Instruction
Installation Of 1W6440 Cylinder Head Gasket{1100}
Installation Of 1W6440 Cylinder Head Gasket{1100}
Reconditioning Of Cylinder Heads For Use On Spacer Plate Cylinder Blocks{1101}
Reconditioning Of Cylinder Heads For Use On Spacer Plate Cylinder Blocks{1101}
Use Of The 1P7451 Valve Guide Honing Group{0673, 1104}
Use Of The 1P7451 Valve Guide Honing Group{0673, 1104}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Use Of 6V9050 Exhaust Stud Removal Group{1100}
Use Of 6V9050 Exhaust Stud Removal Group{1100}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Specifications
Cylinder Head<BR> (For Engines With Spacer Plate)
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Head<BR> (For Engines Without Spacer Plate)
D353 INDUSTRIAL & MARINE ENGINES
Valves
D353 INDUSTRIAL & MARINE ENGINES
Tool Operating Manual
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
Reuse And Salvage Guidelines
Engine Valve Failure Modes{1100, 1105}
Engine Valve Failure Modes{1100, 1105}
Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}
Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}
Applied Failure Analysis
Engine Valve Failure Modes{1100, 1105}
Engine Valve Failure Modes{1100, 1105}
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Disassembly and Assembly
Precombustion Chambers
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Head Assembly (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Head Assembly (Later)
D353 INDUSTRIAL & MARINE ENGINES
Valves
D353 INDUSTRIAL & MARINE ENGINES
Valve Seat Inserts
D353 INDUSTRIAL & MARINE ENGINES
Valve Guides
D353 INDUSTRIAL & MARINE ENGINES
Water Directors
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Inlet And Exhaust Valves And Valve Guides Have Tighter Fit To Prevent Corrosion And Guide Wear{1104,1105,1101,1103,1108,1109}
1981/03/16
Improved Head Gasket Has Larger Fire Ring To Decrease Fretting {1101,1201}
1981/10/26
Improved Head Gasket Has Larger Fire Ring To Decrease Fretting{1101,1201}
1982/01/11
Vacuum Tester Checks For Leaks Between Valve Face and Seat{0651,1103,1105}
1982/09/06
New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip {0653,1216,1105}
1982/11/29
Engine Valve Stem &quot;Use Again&quot; Specifications{0653,1105}
1983/02/28
New Water Seals Used In Cylinder Head Groups{1115,1101}
1983/08/15
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}
1983/10/17
Valve Lash Adjustment Not A Warranty Item {1102,1105}
1985/01/14
Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02
Valve Lash Adjustment Interval Is Changed {1105}
1986/07/07
Exhaust Valve Guides With A Counterbore Are Now Available{1104}
1977/01/24
Improved Cylinder Block With Spacer Plate Used With New Cylinder Heads, Cylinder Head Gaskets, Cylinder Liners And Timing Gear Housing{1101,1162,1201,1216}
1977/05/02
Correct Installation Of Valve Lifters On The Camshaft Is Very Important To Prevent Failures{1209}
1977/05/16
Tools Now Available To Ream And/Or Hone 0.500&quot; (12.70 mm) Diameter Valve Guides{0663}
1977/08/22
Tolerance Added To Valve Clearance Specifications{1105,0374}
1978/01/16
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}
1978/01/30
Use Again Specifications For Valve Springs Are Changed{1108}
1978/03/06
Use New Tools To Adapt Former Cylinder Heads With Counterbores To Cylinder Blocks With Spacer Plates{0600,1100,1101,1201}
1978/05/22
Information About The Use Of Earlier Cylinder Heads And Liners With Spacer Plate Cylinder Blocks; List Of Earlier Articles{0600,1101,1162,1201,1216,1221}
1979/03/26
New Exhaust Valve Has Improved Three-Piece Construction{1105}
1979/04/09
A New Method To Clean And Polish Engine Valve Stems{0674,1105}
1979/05/28
New Cylinder Head Gasket Has Smaller Diameter Cylinder Openings To Improve Location Of Combustion Seal Ring{1101,1201}
1979/08/13
Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27
Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17
Too Much Clearance For Exhaust Valves Can Cause Wear To The Camshaft Lobes And Valve Lifters{1105,1210,1209}
1979/12/24
New Exhaust Valves Are Used In Caterpillar Remanufactured Cylinder Heads{1105,1101}
1990/10/08
Specifications
Vibration Damper
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Vibration Damper And Pulley
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23
8T5314 Socket Adapter Available To Correctly Install Alternator Pulley Nut {0601}
1988/01/25
Engine News
Change To Gear On Accessory Drive Shaft Assembly Gives Longer Service Life
1980/02/06
Specifications
Accessory Drive Group
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Accessory Drive Housing
D353 INDUSTRIAL & MARINE ENGINES
Front Cover
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Change To Gear On Accessory Drive Shaft Assembly Gives Longer Service Life{1207,1206}
1980/02/04
Engine News
Change To Gear On Accessory Drive Shaft Assembly Gives Longer Service Life
1980/02/06
Specifications
Accessory Drive Group
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Accessory Drive Housing
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Change To Gear On Accessory Drive Shaft Assembly Gives Longer Service Life{1207,1206}
1980/02/04
Engine News
Correct Lubrication Procedure Will Prevent Damage To Fan Drive
1982/03/17
Disassembly and Assembly
Fan Drive
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Correct Lubrication Procedure Will Prevent Damage To Fan Drive{1359,0374,0375}
1982/03/08
Disassembly and Assembly
Water Pump
D353 INDUSTRIAL & MARINE ENGINES
Oil Pump Drive
D353 INDUSTRIAL & MARINE ENGINES
Special Instruction
Analyzing Cylinder Condition By Measuring Air Flow{0651, 1000}
Analyzing Cylinder Condition By Measuring Air Flow{0651, 1000}
Dynamometer Test Specifications For Caterpillar Engines{1000}
Dynamometer Test Specifications For Caterpillar Engines{1000}
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Oil and Your Engine {1000}
Oil and Your Engine {1000}
Service Magazine
Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22
Separate Valve Stem Gauges Available{0653,1000}
1982/06/07
Analyzing A Major Engine Failure{1000}
1982/07/19
Reference Chart for Engine Improvements{0374,1000}
1982/10/25
New Index Lists Engine Special Instructions By SMCS Code{1000,0374}
1986/04/07
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16
Testing The Starter On The Engine{1401,1450}
1987/05/04
The Caterpillar Fuel Flow Monitor System Available {0782,1000,1250}
1987/05/11
Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25
Microfiche For Replacement Engine Bills Of Material {0374,1000}
1987/10/26
Explanation Of Nomenclature Used In Engine Performance{1000,0374}
1978/05/15
Sleeve-Type Ring Compressors Can Be Used For Installation Of Pistons From The Bottom Of The Engine{0622}
1978/08/21
Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23
Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24
Check The Radiator Fan Spider Assembly When Doing Yearly General Maintenance{1356}
1989/07/24
Engine Coolant Can Be Recycled{1395}
1989/11/13
Engine News
Locks No Longer Used On Flywheel Bolts; New Torque Specifications For Flywheel Bolts
1981/06/03
Use Of Engine Supports On Flywheel Housing Can Change Face And Bore Runout Measurements
1981/10/21
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts
1987/03/01
More Bolts Hold Flywheel Housing Group
1977/08/24
Specifications
Flywheel
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Housing
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Runout
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Housing Runout
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Housing Bore
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Flywheel
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Housing
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Locks No Longer Used On Flywheel Bolts; New Torque Specifications For Flywheel Bolts{1156}
1981/06/01
Use Of Engine Supports On Flywheel Housing Can Change Face And Bore Runout Measurements{1157}
1981/10/12
Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
Labyrinth-Type Seal Ring Available For Rear Power Takeoff{3055}
1983/04/04
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16
Engine News
Improved Cylinder Block With Spacer Plate Used With New Cylinder Heads, Cylinder Head Gaskets, Cylinder Liners And Timing Gear Housing
1977/05/03
Overlap Joint On Crankshaft Front Seal Ring Prevents Leakage
1978/08/30
Specifications
Camshaft And Timing Gears
D353 INDUSTRIAL & MARINE ENGINES
Gear Group<BR> (Camshaft Idler and Power Take-Off Idler)
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Front Cover
D353 INDUSTRIAL & MARINE ENGINES
Crankshaft Front Seal
D353 INDUSTRIAL & MARINE ENGINES
Timing Gears
D353 INDUSTRIAL & MARINE ENGINES
Timing Gear Housing
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Change To Gear On Accessory Drive Shaft Assembly Gives Longer Service Life{1207,1206}
1980/02/04
Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22
Labyrinth-Type Seal Ring Available For Rear Power Takeoff{3055}
1983/04/04
Improved Cylinder Block With Spacer Plate Used With New Cylinder Heads, Cylinder Head Gaskets, Cylinder Liners And Timing Gear Housing{1101,1162,1201,1216}
1977/05/02
Overlap Joint On Crankshaft Front Seal Ring Prevents Leakage{1160,1202}
1978/08/21
Information About The Use Of Earlier Cylinder Heads And Liners With Spacer Plate Cylinder Blocks; List Of Earlier Articles{0600,1101,1162,1201,1216,1221}
1979/03/26
Engine News
Improved Ring Seal Used At Rear of Crankshaft
1980/01/09
Use Of Engine Supports On Flywheel Housing Can Change Face And Bore Runout Measurements
1981/10/21
More Bolts Hold Flywheel Housing Group
1977/08/24
Specifications
Flywheel Housing
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Housing Runout
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Housing Bore
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Crankshaft Rear Seal
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Housing
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Improved Ring Seal Used At Rear Of Crankshaft {1161}
1980/01/07
Use Of Engine Supports On Flywheel Housing Can Change Face And Bore Runout Measurements{1157}
1981/10/12
Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine{0651,0654,1250}
1982/03/22
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03
Use The 6V2034 Micrometer Adapter To Measure Lip Thickness Of Engine Valves {0653,1105}
1979/10/29
Engine News
Improved Cylinder Block With Spacer Plate Used With New Cylinder Heads, Cylinder Head Gaskets, Cylinder Liners And Timing Gear Housing
1977/05/03
Overlap Joint On Crankshaft Front Seal Ring Prevents Leakage
1978/08/30
Disassembly and Assembly
Front Cover
D353 INDUSTRIAL & MARINE ENGINES
Crankshaft Front Seal
D353 INDUSTRIAL & MARINE ENGINES
Timing Gears
D353 INDUSTRIAL & MARINE ENGINES
Timing Gear Housing
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Change To Gear On Accessory Drive Shaft Assembly Gives Longer Service Life{1207,1206}
1980/02/04
Improved Cylinder Block With Spacer Plate Used With New Cylinder Heads, Cylinder Head Gaskets, Cylinder Liners And Timing Gear Housing{1101,1162,1201,1216}
1977/05/02
Overlap Joint On Crankshaft Front Seal Ring Prevents Leakage{1160,1202}
1978/08/21
Information About The Use Of Earlier Cylinder Heads And Liners With Spacer Plate Cylinder Blocks; List Of Earlier Articles{0600,1101,1162,1201,1216,1221}
1979/03/26
Engine News
Information About The Use Of Earlier Cylinder Heads And Liners With Spacer Plate Cylinder Blocks; List Of Earlier Articles
1979/03/14
New Exhaust Valve Has Improved Three-Piece Construction
1979/04/25
New Filler Bands Give A Better Seal Between The Cylinder Liners And Cylinder Block
1979/05/23
New Cylinder Head Gasket Has Smaller Diameter Cylinder Openings To Improve Location Of Combustion Seal Ring
1979/08/22
New Liner Seat Inserts For Spacer Plate Cylinder Blocks Are Made Of Stainless Steel
1979/09/19
Improved Ring Seal Used At Rear of Crankshaft
1980/01/09
Too Much Clearance For Exhaust Valves Can Cause Wear To The Camshaft Lobes And Valve Lifters
1980/01/09
New Cylinder Liner Has Improved Design To Keep Liner Temperatures Lower
1980/02/06
Change To Gear On Accessory Drive Shaft Assembly Gives Longer Service Life
1980/02/06
New Top Piston Ring Has Plasma-Coated Face
1980/04/30
New Liner Seat Insert For No. 1 And No. 4 Cylinders Of D353 Engines
1980/04/30
In The Future, Oversize And Undersize Connecting Rod And Main Bearings Will Have Size Identification Marks In Metric Units
1980/07/09
New Bend Specification For Used Or Field Reground Crankshafts
1980/08/13
Some Valve Lifter Assemblies Have A Black Color On The Finished Surface
1980/08/13
New Camshaft Has Improved Profile (Shape) Of Exhaust Cam To Extend Service Life
1981/01/28
Locks No Longer Used On Flywheel Bolts; New Torque Specifications For Flywheel Bolts
1981/06/03
6V4133 Wedge Bracket Makes Cylinder Liner Removal Easier
1981/07/15
Improved Head Gasket Has Larger Fire Ring To Decrease Fretting
1982/01/20
New Tools Available For Installation Of Cylinder Liner Seats; Service Tools For Counterboring Tool Group
1982/02/10
New Liner Seat Insert With O-Ring Seal Available
1982/02/10
Correct Lubrication Procedure Will Prevent Damage To Fan Drive
1982/03/17
Use Caution During Replacement Of Damaged Nozzle Adapters Or Precombustion Chambers
1983/01/19
Exhaust Valve Guides With A Counterbore Are Now Available
1977/01/28
Improved Cylinder Block With Spacer Plate Used With New Cylinder Heads, Cylinder Head Gaskets, Cylinder Liners And Timing Gear Housing
1977/05/03
Improved Keystone Piston Assembly
1977/05/13
Correct Installation Of Valve Lifters On The Camshaft Is Very Important To Prevent Failures
1977/05/25
Tools To Hone (Machine) Cylinder Liners Are Available To Permit The Use Of Used Cylinder Liners With New Style Pistons
1977/06/29
More Bolts Hold Flywheel Housing Group
1977/08/24
Use Only The Larger Size Inserts To Make A Repair To Cylinder Block Counterbores For Cylinder Liners
1977/09/28
Tolerance Added To Valve Clearance Specifications
1978/01/18
5P8665 Cylinder Liner Puller Makes Liner Removal Easier And Faster
1978/01/18
Use Again Specifications For Valve Springs Are Changed
1978/03/01
New 5P8709 Piston Tool Group For The Alignment Of Piston Cooling Jets
1978/05/03
Use New Tools To Adapt Former Cylinder Heads With Counterbores To Cylinder Blocks With Spacer Plates
1978/05/24
Change In Procedure To Check Main Bearing Clearance
1978/08/30
Overlap Joint On Crankshaft Front Seal Ring Prevents Leakage
1978/08/30
Special Instruction
Analyzing Cylinder Condition By Measuring Air Flow{0651, 1000}
Analyzing Cylinder Condition By Measuring Air Flow{0651, 1000}
Installation Of 1W6440 Cylinder Head Gasket{1100}
Installation Of 1W6440 Cylinder Head Gasket{1100}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}
Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Cylinder Block Cleaning Procedure{1201}
Cylinder Block Cleaning Procedure{1201}
Crankshaft Seal And Wear Sleeve Installation{1160, 1161}
Crankshaft Seal And Wear Sleeve Installation{1160, 1161}
Installation Of Seal Groups With Hydrodynamic Grooves In The Seal Lip{1160, 1161}
Installation Of Seal Groups With Hydrodynamic Grooves In The Seal Lip{1160, 1161}
Specifications
Camshaft And Timing Gears
D353 INDUSTRIAL & MARINE ENGINES
Accessory Drive Group
D353 INDUSTRIAL & MARINE ENGINES
Gear Group<BR> (Camshaft Idler and Power Take-Off Idler)
D353 INDUSTRIAL & MARINE ENGINES
Valve Rocker Arms And Lifters
D353 INDUSTRIAL & MARINE ENGINES
Camshaft
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Block<BR> (With Spacer Plate)
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Block<BR> (Without Spacer Plate)
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Liner
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Liner Projection<BR> (With Spacer Plate)
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Liner Projection<BR> (Without Spacer Plate)
D353 INDUSTRIAL & MARINE ENGINES
Pistons And Rings<BR> (With Keystone Piston Ring Groove)
D353 INDUSTRIAL & MARINE ENGINES
Pistons And Rings
D353 INDUSTRIAL & MARINE ENGINES
Crankshaft
D353 INDUSTRIAL & MARINE ENGINES
Flywheel
D353 INDUSTRIAL & MARINE ENGINES
Vibration Damper
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Housing
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Runout
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Housing Runout
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Housing Bore
D353 INDUSTRIAL & MARINE ENGINES
Enclosed Clutches
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Fan Drive
D353 INDUSTRIAL & MARINE ENGINES
Accessory Drive Housing
D353 INDUSTRIAL & MARINE ENGINES
Piston Cooling Tubes
D353 INDUSTRIAL & MARINE ENGINES
Oil Pan
D353 INDUSTRIAL & MARINE ENGINES
Crankshaft Main Bearings
D353 INDUSTRIAL & MARINE ENGINES
Rocker Shaft Assembly And Push Rods
D353 INDUSTRIAL & MARINE ENGINES
Rocker Shaft Assembly
D353 INDUSTRIAL & MARINE ENGINES
Spacer Plate
D353 INDUSTRIAL & MARINE ENGINES
Valve Lifters
D353 INDUSTRIAL & MARINE ENGINES
Camshaft
D353 INDUSTRIAL & MARINE ENGINES
Camshaft Bearings
D353 INDUSTRIAL & MARINE ENGINES
Pistons (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Pistons (Later)
D353 INDUSTRIAL & MARINE ENGINES
Pistons
D353 INDUSTRIAL & MARINE ENGINES
Cylinders Liners (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Cylinder Liners (Later)
D353 INDUSTRIAL & MARINE ENGINES
Vibration Damper And Pulley
D353 INDUSTRIAL & MARINE ENGINES
Front Cover
D353 INDUSTRIAL & MARINE ENGINES
Crankshaft Front Seal
D353 INDUSTRIAL & MARINE ENGINES
Flywheel
D353 INDUSTRIAL & MARINE ENGINES
Crankshaft Rear Seal
D353 INDUSTRIAL & MARINE ENGINES
Flywheel Housing
D353 INDUSTRIAL & MARINE ENGINES
Timing Gears
D353 INDUSTRIAL & MARINE ENGINES
Timing Gear Housing
D353 INDUSTRIAL & MARINE ENGINES
Crankshaft
D353 INDUSTRIAL & MARINE ENGINES
Clutches
D353 INDUSTRIAL & MARINE ENGINES
Clutch Drive Spider
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Change To Gear On Accessory Drive Shaft Assembly Gives Longer Service Life{1207,1206}
1980/02/04
New Top Piston Ring Has Plasma-Coated Face{1215}
1980/03/24
Some Valve Lifter Assemblies Have A Black Color On The Finished Surface{1209}
1980/08/18
New Camshaft Has Improved Profile (Shape) Of Exhaust Cam To Extend Service Life{1210}
1981/02/02
Correct Installation Of Inserts Necessary During Repairs To Prevent More Counterbore Cracks{1217,1201}
1981/03/09
Locks No Longer Used On Flywheel Bolts; New Torque Specifications For Flywheel Bolts{1156}
1981/06/01
Use Of Engine Supports On Flywheel Housing Can Change Face And Bore Runout Measurements{1157}
1981/10/12
Use Of A Flex-Hone For Cylinder Liner Reconditioning{0664,0674,1216}
1981/12/21
Piston And Connecting Rod Assembly Storage Cabinet{0600}
1982/01/18
New Tools Available For Installation Of Cylinder Liner Seats; Service Tools For Counterboring Tool Group{0622,1217}
1982/01/25
New Liner Seat Insert With O-Ring Seal Available{1217,1216}
1982/01/25
Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22
Use 6V6035 Hardness Tester On Crankshafts{0651,1202}
1982/02/22
Correct Lubrication Procedure Will Prevent Damage To Fan Drive{1359,0374,0375}
1982/03/08
Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine{0651,0654,1250}
1982/03/22
Separate Valve Stem Gauges Available{0653,1000}
1982/06/07
Information Available For The Installation Of Inserts In Cylinder Blocks And Spacer Plates{1217,1201,0664}
1982/07/05
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
New Main And Connecting Rod Bearings Have A Thicker Layer Of Lead-Tin Overlay (Surface Material){1230,1203,1219}
1982/10/11
Reference Chart for Engine Improvements{0374,1000}
1982/10/25
Use 6V6147 Polishing Wheel To Clean Piston Pins{0675,1214}
1982/11/08
Use the 6V6167 Contact Point to Measure Wear Steps on Piston Pins{0653}
1982/11/22
Engine Valve Stem &quot;Use Again&quot; Specifications{0653,1105}
1983/02/28
Labyrinth-Type Seal Ring Available For Rear Power Takeoff{3055}
1983/04/04
Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16
Reuse Of Engine Bearings{1230}
1983/05/16
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}
1983/10/17
Crankshaft Failures{1202,1230}
1983/11/21
Reuse Of Engine Bearings{1230,1219,1203}
1983/11/21
Remanufactured Undersize Crankshafts Are Available{1202}
1983/11/21
Installing New Copper Bonded Bearings Can Extend Engine Life{1230,1203,1219}
1985/04/29
Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27
Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03
Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07
Remanufactured Crankshafts Are Available In Standard And Two Undersize Dimensions (U.S. and Canada){1202,7754}
1985/11/18
New 8T2998 Lubricant Available{0645,1210}
1986/02/17
New Index Lists Engine Special Instructions By SMCS Code{1000,0374}
1986/04/07
Increase Piston Reuse With Keystone Piston Ring Gauge Group{1214,1215}
1986/06/16
Bearing Failures On Engines Due To Lack Of Lubrication{1230,1219,1203,1202}
1986/09/08
Check Connecting Rods After Engine Failures Involving Hydraulic Lock{1218,1225}
1986/10/20
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
Exhaust Valve Guides With A Counterbore Are Now Available{1104}
1977/01/24
Improved Cylinder Block With Spacer Plate Used With New Cylinder Heads, Cylinder Head Gaskets, Cylinder Liners And Timing Gear Housing{1101,1162,1201,1216}
1977/05/02
Improved Keystone Piston Assembly{1214,1216}
1977/05/02
Tools To Hone (Machine) Cylinder Liners Are Available To Permit The Use Of Used Cylinder Liners With New Style Pistons{0664,1214,1216}
1977/07/04
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08
Tools Now Available To Ream And/Or Hone 0.500&quot; (12.70 mm) Diameter Valve Guides{0663}
1977/08/22
Use Only The Larger Size Inserts To Make A Repair To Cylinder Block Counterbores For Cylinder Liners{1201,1216,1217}
1977/10/10
Crankshaft Support Groups Are Available To Measure Bent Crankshafts{0653,1202}
1977/11/07
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
The Caterpillar Fuel Flow Monitor System Available {0782,1000,1250}
1987/05/11
Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group {0781,1200,1350}
1987/07/20
Microfiche For Replacement Engine Bills Of Material {0374,1000}
1987/10/26
Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23
5P8665 Cylinder Liner Puller Makes Liner Removal Easier And Faster{0621,1216}
1978/01/09
Tolerance Added To Valve Clearance Specifications{1105,0374}
1978/01/16
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}
1978/01/30
Use Again Specifications For Valve Springs Are Changed{1108}
1978/03/06
Use 6V100 Tool Arrangement To Remove And Install Piston Pin Bearings For Both Tapered And Standard Connecting Rods{0620,1218}
1978/04/24
Explanation Of Nomenclature Used In Engine Performance{1000,0374}
1978/05/15
Use New Main Bearings In Replacement Cylinder Blocks{1203,1201}
1978/06/12
Overlap Joint On Crankshaft Front Seal Ring Prevents Leakage{1160,1202}
1978/08/21
Sleeve-Type Ring Compressors Can Be Used For Installation Of Pistons From The Bottom Of The Engine{0622}
1978/08/21
Improved Piston Pins Are Made Of Different Material For Better Hardness Characteristics When Heat Treated{1214}
1978/08/21
Change In Procedure To Check Main Bearing Clearance{1203}
1978/08/28
New 6V87 Gauge Measures Valve Stem Wear{0653,1105}
1979/01/08
Current Chart For Dynamometer Adapters{0651,1000}
1979/01/22
5P3519 Piston Ring Gauge Has Improved Design For Better Accuracy And Easier Use; Corrected Information For Use On Pistons That Have Two Ring Grooves{0653,1214}
1979/05/14
New Filler Bands Give A Better Seal Between The Cylinder Liners And Cylinder Block{1201,1216}
1979/05/14
A New Method To Clean And Polish Engine Valve Stems{0674,1105}
1979/05/28
New Centering Rings For Oversized Main Bearings{0665,1230}
1979/06/04
New Cylinder Head Gasket Has Smaller Diameter Cylinder Openings To Improve Location Of Combustion Seal Ring{1101,1201}
1979/08/13
Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27
Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}
1979/09/03
Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24
Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17
Too Much Clearance For Exhaust Valves Can Cause Wear To The Camshaft Lobes And Valve Lifters{1105,1210,1209}
1979/12/24
Check The Radiator Fan Spider Assembly When Doing Yearly General Maintenance{1356}
1989/07/24
Engine Coolant Can Be Recycled{1395}
1989/11/13
New Exhaust Valves Are Used In Caterpillar Remanufactured Cylinder Heads{1105,1101}
1990/10/08
Engine News
Use Of Engine Supports On Flywheel Housing Can Change Face And Bore Runout Measurements
1981/10/21
Special Instruction
Installation Of 5N1678 Rear Power Take-Off Clutch Support Group{1007}
Installation Of 5N1678 Rear Power Take-Off Clutch Support Group{1007}
Service Magazine
Use Of Engine Supports On Flywheel Housing Can Change Face And Bore Runout Measurements{1157}
1981/10/12
Disassembly and Assembly
Oil Pan
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
Engine News
&quot;Off-Size&quot; Bearing Kits Available
1991/10/01
Service Magazine
Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/03
Engine News
New Top Piston Ring Has Plasma-Coated Face
1980/04/30
In The Future, Oversize And Undersize Connecting Rod And Main Bearings Will Have Size Identification Marks In Metric Units
1980/07/09
New Piston Ring Assemblies Give Improved Ring And Cylinder Liner Life
1981/04/22
New Main And Connecting Rod Bearings Have A Thicker Layer Of Lead-Tin Overlay (Surface Material)
1982/10/20
Use 6V6147 Polishing Wheel To Clean Piston Pins
1982/11/10
Remanufactured Connecting Rod Assemblies
1984/02/22
Increase Piston Reuse With Keystone Piston Ring Gauge Group
1986/07/01
Check Connecting Rods After Engine Failures Involving Hydraulic Lock
1986/12/01
Main And Connecting Rod Bearing Part Numbers
1987/01/01
Use Only Paint To Mark Connecting Rod Caps For Torque-Turn Method
1987/06/01
Improved Keystone Piston Assembly
1977/05/13
New 5P8709 Piston Tool Group For The Alignment Of Piston Cooling Jets
1978/05/03
New Guidelines for Inspecting Pistons {1214}
2006/01/02
Special Instruction
Piston Cleaning Procedure{1214}
Piston Cleaning Procedure{1214}
Installation Of 7N5037 Piston Group{1214}
Installation Of 7N5037 Piston Group{1214}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Using The 5P2050 Connecting Rod Checking Fixture{0767, 1218}
Using The 5P2050 Connecting Rod Checking Fixture{0767, 1218}
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
Piston Ring Gap Alignment Influence on High Blowby and Oil Consumption on All Engines {1000, 1215}
Technical Information Bulletin
Specifications
Connecting Rod
D353 INDUSTRIAL & MARINE ENGINES
Pistons And Rings<BR> (With Keystone Piston Ring Groove)
D353 INDUSTRIAL & MARINE ENGINES
Pistons And Rings
D353 INDUSTRIAL & MARINE ENGINES
Tool Operating Manual
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
Disassembly and Assembly
Connecting Rod Bearings
D353 INDUSTRIAL & MARINE ENGINES
Pistons (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Pistons (Later)
D353 INDUSTRIAL & MARINE ENGINES
Pistons
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Top Piston Ring Has Plasma-Coated Face{1215}
1980/03/24
New Piston Ring Assemblies Give Improved Ring And Cylinder Liner Life{1215,1213}
1981/04/06
Piston And Connecting Rod Assembly Storage Cabinet{0600}
1982/01/18
Use New Special Instruction To Install 5P6595 Insert In Cylinder Liner Seats{1216,0621}
1982/05/03
Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/03
New Bearing Standard: Quantity Of One Part Number Now Has Both Halves Of The Bearing{7551}
1982/08/09
New Main And Connecting Rod Bearings Have A Thicker Layer Of Lead-Tin Overlay (Surface Material){1230,1203,1219}
1982/10/11
Use 6V6147 Polishing Wheel To Clean Piston Pins{0675,1214}
1982/11/08
Use the 6V6167 Contact Point to Measure Wear Steps on Piston Pins{0653}
1982/11/22
Reuse Of Engine Bearings{1230}
1983/05/16
Reuse Of Engine Bearings{1230,1219,1203}
1983/11/21
Remanufactured Connecting Rod Assemblies{1218}
1984/01/23
Installing New Copper Bonded Bearings Can Extend Engine Life{1230,1203,1219}
1985/04/29
Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07
Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02
Increase Piston Reuse With Keystone Piston Ring Gauge Group{1214,1215}
1986/06/16
Bearing Failures On Engines Due To Lack Of Lubrication{1230,1219,1203,1202}
1986/09/08
Check Connecting Rods After Engine Failures Involving Hydraulic Lock{1218,1225}
1986/10/20
Improved Keystone Piston Assembly{1214,1216}
1977/05/02
Main And Connecting Rod Bearing Part Numbers {1203,1219,1230}
1987/01/26
Use Only Paint To Mark Connecting Rod Caps For Torque-Turn Method {1218,1219}
1987/06/01
Locating Bushings For The 5P3550 Rod Boring Machine Will Now Hold Tapered Piston Pin Bushings {0626}
1978/04/17
Use 6V100 Tool Arrangement To Remove And Install Piston Pin Bearings For Both Tapered And Standard Connecting Rods{0620,1218}
1978/04/24
Sleeve-Type Ring Compressors Can Be Used For Installation Of Pistons From The Bottom Of The Engine{0622}
1978/08/21
Improved Piston Pins Are Made Of Different Material For Better Hardness Characteristics When Heat Treated{1214}
1978/08/21
5P3519 Piston Ring Gauge Has Improved Design For Better Accuracy And Easier Use; Corrected Information For Use On Pistons That Have Two Ring Grooves{0653,1214}
1979/05/14
Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27
Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
Check The Radiator Fan Spider Assembly When Doing Yearly General Maintenance{1356}
1989/07/24
Engine Coolant Can Be Recycled{1395}
1989/11/13
Special Instruction
Installation Of 5N1678 Rear Power Take-Off Clutch Support Group{1007}
Installation Of 5N1678 Rear Power Take-Off Clutch Support Group{1007}
Procedure For Conversion From Oil Lubrication To Grease Lubrication For Rear Power Takeoff Clutches{3055}
Procedure For Conversion From Oil Lubrication To Grease Lubrication For Rear Power Takeoff Clutches{3055}
Service Magazine
Labyrinth-Type Seal Ring Available For Rear Power Takeoff{3055}
1983/04/04
Clutch (PTO) Warranty On Morbark Industries Products Powered By Caterpillar Engines{7758}
1992/07/20
Engine News
8T5314 Socket Adapter Available To Correctly Install Alternator Pulley Nut
1988/01/01
Special Instruction
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Disassembly and Assembly
Fan Drive
D353 INDUSTRIAL & MARINE ENGINES
Vibration Damper And Pulley
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23
Correct Lubrication Procedure Will Prevent Damage To Fan Drive{1359,0374,0375}
1982/03/08
Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01
Identification Of External Terminals On Alternators{1405,1406,1400}
1987/03/23
Alternator &quot;R&quot; Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04
Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04
Check Alternator Output Connection Prior To Machine Delivery{1405}
1987/05/18
Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25
Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23
8T5314 Socket Adapter Available To Correctly Install Alternator Pulley Nut {0601}
1988/01/25
New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13
Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22
Engine News
New 6V87 Gauge Measures Valve Stem Wear
1979/01/10
Separate Valve Stem Gauges Available
1982/08/25
Use FT1711 Light Table For Cylinder Liner Inspection
1982/12/15
Use 6V7777 Spacer With 9S6030 Front Oil Seal Installer
1983/04/27
New Service Centers For 6V3100 Engine Timing Indicator Group
1983/10/26
New Engine Timing Indicator Group Available
1986/07/01
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity
1986/11/01
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups
1987/03/01
Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group
1987/07/01
Special Instruction
Troubleshooting And Repair Of The 5P2160 Engine Horsepower Meter Arrangement<SUP><FONT SIZE=-1>*</FONT></SUP>{0781, 0782}
Troubleshooting And Repair Of The 5P2160 Engine Horsepower Meter Arrangement*{0781, 0782}
Using The 5P2160 Engine Horsepower Meter Arrangement<SUP><FONT SIZE=-1>*</FONT></SUP>{0781, 0782}
Using The 5P2160 Engine Horsepower Meter Arrangement*{0781, 0782}
Using The 4S6553 Engine Evaluation Test Group{0781}
Using The 4S6553 Engine Evaluation Test Group{0781}
Dynamometer Test Specifications For Caterpillar Engines{1000}
Dynamometer Test Specifications For Caterpillar Engines{1000}
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
Electronic Repair Of 6V3100 Diesel Engine Timing Indicator{0651, 1250}
Electronic Repair Of 6V3100 Diesel Engine Timing Indicator{0651, 1250}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Using the 1U5470 Engine Pressure Group{0781}
Using the 1U5470 Engine Pressure Group{0781}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Using the 4C6821 Injection Line Speed Pickup Group{0781}
Using the 4C6821 Injection Line Speed Pickup Group{0781}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Technical Information Bulletin
368-9910 Multi-Tool Group with the 368-9911 Burn Rate Group Accuracy Issue{0599, 0701, 0702, 0706, 1000, 7610, 7620}
368-9910 Multi-Tool Group with the 368-9911 Burn Rate Group Accuracy Issue{0599, 0701, 0702, 0706, 1000, 7610, 7620}
Tool Operating Manual
Using The Inspection Borescopes 1U5268 and 8T9290 Borescopes
Using The Inspection Borescopes 1U5268 and 8T9290 Borescopes
NEHS0566 <NOBR> 4C-9832</NOBR> Large Engine Roll-Over Stand {0599, 0701}
NEHS0566 4C-9832 Large Engine Roll-Over Stand {0599, 0701}
NEHS1111: 368-9910 Multi-Tool Group 3 {0599, 0701, 0702, 0706, 1000, 7610, 7620}
NEHS1111: 368-9910 Multi-Tool Group 3 {0599, 0701, 0702, 0706, 1000, 7610, 7620}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
Reuse And Salvage Guidelines
Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}
Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}
Service Magazine
Piston And Connecting Rod Assembly Storage Cabinet{0600}
1982/01/18
New Tools Available For Installation Of Cylinder Liner Seats; Service Tools For Counterboring Tool Group{0622,1217}
1982/01/25
Use New Special Instruction To Install 5P6595 Insert In Cylinder Liner Seats{1216,0621}
1982/05/03
Use 6V6147 Polishing Wheel To Clean Piston Pins{0675,1214}
1982/11/08
Make Change To 6V2100 Multitach And 5P9698 Calibrator{0651}
1982/11/15
Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16
Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27
Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03
New Engine Timing Indicator Group Available {0781,0782}
1986/07/07
New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27
New Special Instruction For Troubleshooting 5P2150 Engine Horsepower Meter{0651,1250}
1977/01/17
Troubleshooting The Tachometer System Of The 4S6553 Engine Instrument Group{0651}
1977/10/10
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group {0781,1200,1350}
1987/07/20
Four New Contact Points Added To 5P6524 Engine Timing Indicator Group{0653}
1978/08/07
Extraction Tools For &quot;Live Oil Sampling&quot;{7770,0770,0781,0783,0784}
1988/04/18
Installation Of Valves For Live Oil Sampling{7770,0770,0781,0783,0784}
1988/06/06
New 6V87 Gauge Measures Valve Stem Wear{0653,1105}
1979/01/08
Current Chart For Dynamometer Adapters{0651,1000}
1979/01/22
6V117 And 6V2001 Bushings Used In 9S8140 Pressurizing Pump Group Are Available For Parts Service{0651}
1979/06/25
40 Power Microscope is Available for Inspecting Bearing Journals on Crankshafts {0777, 1202}
2006/01/16
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}
Engine News
Too Much Clearance For Exhaust Valves Can Cause Wear To The Camshaft Lobes And Valve Lifters
1980/01/09
Some Valve Lifter Assemblies Have A Black Color On The Finished Surface
1980/08/13
Use Caution During Replacement Of Damaged Nozzle Adapters Or Precombustion Chambers
1983/01/19
Engine Valve Stem &quot;Use Again&quot; Specifications
1983/03/16
A New Book &quot;Analyzing Diesel And Natural Gas Engine Valve Failures&quot; Is Available
1985/03/01
Valve Lash Adjustment Interval Is Changed
1986/07/01
New Exhaust Valves Are Used In Caterpillar Remanufactured Cylinder Heads
1990/10/01
Correct Installation Of Valve Lifters On The Camshaft Is Very Important To Prevent Failures
1977/05/25
Tolerance Added To Valve Clearance Specifications
1978/01/18
Use Again Specifications For Valve Springs Are Changed
1978/03/01
Special Instruction
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Use Of The 1P7451 Valve Guide Honing Group{0673, 1104}
Use Of The 1P7451 Valve Guide Honing Group{0673, 1104}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Use Of 6V9050 Exhaust Stud Removal Group{1100}
Use Of 6V9050 Exhaust Stud Removal Group{1100}
Specifications
Valve Rocker Arms And Lifters
D353 INDUSTRIAL & MARINE ENGINES
Information Release Memo
REMANUFACTURED LIFTERS FOR THE D &amp; G SERIES ENGINES
REMANUFACTURED LIFTERS FOR THE D & G SERIES ENGINES
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Disassembly and Assembly
Rocker Shaft Assembly And Push Rods
D353 INDUSTRIAL & MARINE ENGINES
Rocker Shaft Assembly
D353 INDUSTRIAL & MARINE ENGINES
Valve Lifters
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Some Valve Lifter Assemblies Have A Black Color On The Finished Surface{1209}
1980/08/18
Engine Valve Stem &quot;Use Again&quot; Specifications{0653,1105}
1983/02/28
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}
1983/10/17
Valve Lash Adjustment Not A Warranty Item {1102,1105}
1985/01/14
Valve Lash Adjustment Interval Is Changed {1105}
1986/07/07
Correct Installation Of Valve Lifters On The Camshaft Is Very Important To Prevent Failures{1209}
1977/05/16
Tools Now Available To Ream And/Or Hone 0.500&quot; (12.70 mm) Diameter Valve Guides{0663}
1977/08/22
Tolerance Added To Valve Clearance Specifications{1105,0374}
1978/01/16
Valve Damage Can Be Caused By Short Intervals Of Engine Operation In Very Cold Temperatures{1105,1208}
1978/01/30
Use Again Specifications For Valve Springs Are Changed{1108}
1978/03/06
A New Method To Clean And Polish Engine Valve Stems{0674,1105}
1979/05/28
Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27
Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17
Too Much Clearance For Exhaust Valves Can Cause Wear To The Camshaft Lobes And Valve Lifters{1105,1210,1209}
1979/12/24
New Exhaust Valves Are Used In Caterpillar Remanufactured Cylinder Heads{1105,1101}
1990/10/08
Disassembly and Assembly
Flywheel Housing
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Use Of Engine Supports On Flywheel Housing Can Change Face And Bore Runout Measurements{1157}
1981/10/12
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23

Truck sale:

CAT D353E
USD $22,500 
CAT D353E

Contractor Sales
Pocatello, Idaho
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.