AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

D353E MARINE ENGINE 47B00409-UP FUEL SYSTEM Caterpillar SIS



MARINE ENGINE D353E MARINE ENGINE 47B
 D353E MARINE ENGINE 47B00409-UP UE034303 D353E 47B   (1980)

Parts group D353E:

  For full view, you need register
FUEL SYSTEM
CONTROL GP-FUEL RATIO
FUEL RATIO CONTROL GROUP
FUEL RATIO CONTROL GROUP
FUEL RATIO CONTROL GROUP
Serial No. 47B3510 to 47B4902 inclusive
4N4678 Fuel Ratio Control parts are shown on Pages 38B-4 & 38C
CONTROL GP-FUEL RATIO
4N-6510 CONTROL GP-FUEL RATIO
4N6510 FUEL RATIO CONTROL GROUP
Serial No. 47B4903-Up
4N4678 Fuel Ratio Control parts are shown on Pages 38B-4 & 38C
CONTROL GP-FUEL RATIO
4N-4678 CONTROL GP-FUEL RATIO
4N4678 FUEL RATIO CONTROL GROUP
Serial No. 47B3510 to 47B3541 inclusive
Part of Fuel Ratio Control shown on Page 38B-3
CONTROL GP-FUEL RATIO
4N-4678 CONTROL GP-FUEL RATIO
4N4678 FUEL RATIO CONTROL GROUP
Serial No. 47B3542 to 47B4004 inclusive
Part of 4N6510 Fuel Ratio Control Group shown on Page 38B-3
CONTROL GP-FUEL RATIO
4N-4678 CONTROL GP-FUEL RATIO
4N4678 FUEL RATIO CONTROL GROUP--Type 1
Serial No. 47B4005-Up
Part of 4N6510 Fuel Ratio Control Group shown on Page 38B-3
CONTROL GP-FUEL RATIO
4N-4678 CONTROL GP-FUEL RATIO
4N4678 FUEL RATIO CONTROL GROUP--Type 2
Serial No. 47B4005-Up
Part of 4N6510 Fuel Ratio Control Group shown on Page 38B-3
CONTROL GP-GOVERNOR
GOVERNOR CONTROL CHART
5L-2535 GOVERNOR CONTROL CHART
GOVERNOR CONTROL CHART (5L2535 N/S)
GOVERNOR CONTROL GROUP
3L-8869 GOVERNOR CONTROL GROUP
3L8869 GOVERNOR CONTROL GROUP--R.H.
Refer to Page 81 for usage
GOVERNOR CONTROL GROUP
5L-2518 GOVERNOR CONTROL GROUP
5L2518 GOVERNOR CONTROL GROUP--L.H.
Refer to Page 81 for usage
Also part of 5L7479 Single Lever Control Arrangement listed on Page 115
GOVERNOR CONTROL GROUP
4N-9847 GOVERNOR CONTROL GROUP
4N9847 GOVERNOR CONTROL GROUP--Vernier & Positive Locking
Serial No. 47B3510-Up
FOR USE WITH HYDROMECHANICAL GOVERNOR
CONTROL GP-GOVERNOR
4N-3829 CONTROL GP-GOVERNOR
4N3829 GOVERNOR CONTROL GROUP--Vernier & Positive Locking
Serial No. 47B3510-Up
Part of 4N9847 Governor Control Group
GOVERNOR CONTROL GROUP
4N-9848 GOVERNOR CONTROL GROUP
4N9848 GOVERNOR CONTROL GROUP--Positive Locking
Serial No. 47B3510-Up
FOR USE WITH HYDROMECHANICAL GOVERNOR
CONTROL GP-GOVERNOR
4N-3830 CONTROL GP-GOVERNOR
4N3830 GOVERNOR CONTROL GROUP--Positive Locking
Serial No. 47B3510-Up
Part of 4N9848 Governor Control Group
GOVERNOR CONTROL GROUP
4N-9846 GOVERNOR CONTROL GROUP
4N9846 GOVERNOR CONTROL GROUP--Remote & Positive Locking
Serial No. 47B3510-Up
FOR USE WITH HYDROMECHANICAL GOVERNOR
CONTROL GP-GOVERNOR
4N-3828 CONTROL GP-GOVERNOR
4N3828 GOVERNOR CONTROL GROUP--Remote & Positive Locking
Serial No. 47B3510-Up
Part of 4N9846 Governor Control Group
HANDLE GP-CONTROL
4L-7604 HANDLE GP-CONTROL
4L7604 HANDLE GROUP
Part of 3L8869 and 5L2518 Governor Control Groups
Refer to Page 81 for usage
ACTUATOR GROUP
2L-6745 ACTUATOR GROUP
2L6745 ACTUATOR GROUP
Serial No. 47B409 to 47B3509 inclusive
Refer to Page 81 for usage
MOUNTING GP-ACTUATOR
3N-9592 MOUNTING GP-ACTUATOR
3N9592 ACTUATOR MOUNTING GROUP
FOR USE WITH 7231 MARINE GEAR
ACTUATOR GP-AIR
2N-6006 ACTUATOR GP-AIR
2N6006 AIR ACTUATOR GROUP--Type 2
Serial No. 47B3510-Up
Part of 3N5862 Air Actuated Governor Control Group shown on Page 83B
AIR ACTUATED GOVERNOR CONTROL GROUP
3N-5862 AIR ACTUATED GOVERNOR CONTROL GROUP
3N5862 AIR ACTUATED GOVERNOR CONTROL GROUP
Serial No. 47B3510-Up
ACTUATOR GP-AIR
2N-6006 ACTUATOR GP-AIR
AIR ACTUATOR (2N6006 N/S)--Type 1
Serial No. 47B3510-Up
Part of 3N5862 Air Actuated Governor Control Group
LEVER GROUP
4L-6811 LEVER GROUP
4L6811 LEVER GROUP
Refer to Page 81 for usage
5L-1889 CONTROL GP
5L1889 PNEUMATIC REMOTE CONTROL GROUP--Pilot House
Heavy Duty--"Z" Slot Lever Operation
Note: These Groups are used in conjunction with an Engine Mounted Control Group
and an Air Actuated Governor Control Group
5L-1890 CONTROL GP
5L1890 PNEUMATIC REMOTE CONTROL GROUP--Pilot House
Straight-through Lever Operation
Note: These Groups are used in conjunction with an Engine Mounted Control Group
and an Air Actuated Governor Control Group
PNEUMATIC CONTROL GROUP
5L-1887 PNEUMATIC CONTROL GROUP
5L1887 PNEUMATIC CONTROL GROUP--Remote--Engine Mounted
For use with Air Actuated Governor Control Groups
PNEUMATIC REMOTE CONTROL GROUP
3N-8853 PNEUMATIC REMOTE CONTROL GROUP
3N8853 PNEUMATIC REMOTE CONTROL GROUP--Engine Mounted-Type 1
FOR USE WITH 7231 MARINE GEAR
PNEUMATIC REMOTE CONTROL GROUP
3N-8853 PNEUMATIC REMOTE CONTROL GROUP
3N8853 PNEUMATIC REMOTE CONTROL GROUP--Engine Mounted--Type 2
FOR USE WITH 7231 MARINE TRANSMISSION
GOVERNOR CONTROL GROUP
6L-3194 GOVERNOR CONTROL GROUP
6L3194 GOVERNOR CONTROL GROUP--Hydraulic
Serial No. 47B409 to 47B3509 inclusive
GOVERNOR CONTROL GROUP
6L-7658 GOVERNOR CONTROL GROUP
6L7658 GOVERNOR CONTROL GROUP--Remote Engine Mounted--Replaces 5L1887-Type 1
FOR USE WITH AIR ACTUATED GOVERNOR CONTROL GROUPS
GOVERNOR CONTROL GROUP
6L-7658 GOVERNOR CONTROL GROUP
6L7658 GOVERNOR CONTROL GROUP--Remote Engine Mounted--Type 2
FOR USE WITH AIR ACTUATED GOVERNOR CONTROL GROUPS
GOVERNOR CONTROL GROUP
3L-3889 GOVERNOR CONTROL GROUP
3L3889 GOVERNOR CONTROL GROUP
Part of 3L3891 Marine Single Lever Control Arrangement
3N-5964 CONTROL GP-GOVERNOR
3N5964 GOVERNOR CONTROL GROUP--Remote--Single Lever
Refer to Chart shown on Page 116-1 for usage
3N-9158 CONTROL GP-GOVERNOR
3N9158 GOVERNOR CONTROL GROUP--Mechanical--Remote--Dual Lever
Refer to Chart shown on Page 116-1 for usage
3N-9173 CONTROL GP-MECHANICAL
3N9173 MECHANICAL CONTROL GROUP--Remote--Dual Lever
Refer to Chart shown on Page 116-1 for usage
CONTROL GP-GOVERNOR
8L-4445 CONTROL GP-GOVERNOR
8L4445 GOVENOR CONTROL GROUP--Remote & Positive Lock
Part of 3N8895 and 3N8350 Engine & Marine Gear
Control Mounting Groups listed on Page 116-4
DRIVE GP-TACHOMETER
TACHOMETER DRIVE GROUP
1F-3290 TACHOMETER DRIVE GROUP
1F3290 TACHOMETER DRIVE GROUP
Part of 4L1714 Electric Tachometer Group listed on Page 89
DRIVE GP-TACHOMETER
4L-5789 DRIVE GP-TACHOMETER
4L5789 TACHOMETER DRIVE GROUP
DRIVE GP-TACHOMETER
1M-5061 DRIVE GP-TACHOMETER
1M5061 TACHOMETER DRIVE GROUP
Part of 4L5789 Tachometer Drive Group
FILTER GP-FUEL
FUEL FILTER GROUP
2L-6985 FUEL FILTER GROUP
2L6985 FUEL FILTER GROUP
Serial No. 47B409 to 47B1612 & 47B1710 to 47B2328 inclusive. Only separate parts serviced
FUEL FILTER
FUEL FILTER
FUEL FILTER
SERIAL NO. 47B1613 TO 47B1709 INCLUSIVE
FILTER GP-FUEL
8L-4941 FILTER GP-FUEL
8L4941 FUEL FILTER GROUP
Serial No. 47B2329-Up. Only separate parts serviced
PRIMARY FUEL FILTER AND LINES GROUP
5L-1463 PRIMARY FUEL FILTER AND LINES GROUP
5L1463 PRIMARY FUEL FILTER AND LINES GROUP--Type 2
8H7204 Filter parts are shown on Page 101
PRIMARY FUEL FILTER AND LINES GROUP
5L-1463 PRIMARY FUEL FILTER AND LINES GROUP
5L1463 PRIMARY FUEL FILTER AND LINES GROUP--Type 1
FILTER GP-FUEL
8H-7204 FILTER GP-FUEL
8H7204 FILTER GROUP--Type 1
Part of 5L1463 Primary Fuel Filter and Lines Group
FILTER GP-FUEL
8H-7204 FILTER GP-FUEL
8H7204 FILTER GROUP--Type 2
Part of 5L1463 Primary Fuel Filter and Lines Group
GOVERNOR GP
FUEL PUMP AND GOVERNOR DRIVE GROUP
5H-1117 FUEL PUMP AND GOVERNOR DRIVE GROUP
5H1117 FUEL PUMP AND GOVERNOR DRIVE GROUP
Serial No. 47B409 to 47B3509 inclusive
DRIVE GP-GOVERNOR
6N-0050 DRIVE GP-GOVERNOR
6N50 FUEL PUMP AND GOVERNOR DRIVE GROUP
Serial No. 47B3510 to 47B4763 inclusive
DRIVE GP-GOVERNOR
6N-0050 DRIVE GP-GOVERNOR
6N50 FUEL PUMP AND GOVERNOR DRIVE GROUP--Part 1 of 2
Serial No. 47B4764-Up
DRIVE GP-GOVERNOR
6N-0050 DRIVE GP-GOVERNOR
6N50 FUEL PUMP AND GOVERNOR DRIVE GROUP--Part 2 of 2
Serial No. 47B4764-Up
DRIVE GP-GOVERNOR
7N-4201 DRIVE GP-GOVERNOR
7N4201 GOVERNOR AND FUEL PUMP DRIVE GROUP--Part 1 of 2
Serial No. 47B4531 to 47B4920 inclusive
DRIVE GP-GOVERNOR
7N-4201 DRIVE GP-GOVERNOR
7N4201 GOVERNOR AND FUEL PUMP DRIVE GROUP--Part 2 of 2
Serial No. 47B4531 to 47B4920 inclusive
DRIVE GP-GOVERNOR
7N-4201 DRIVE GP-GOVERNOR
7N4201 GOVERNOR AND FUEL PUMP DRIVE GROUP--Part 1 of 2
Serial No. 47B4921-Up
DRIVE GP-GOVERNOR
7N-4201 DRIVE GP-GOVERNOR
7N4201 GOVERNOR AND FUEL PUMP DRIVE GROUP--Part 2 of 2
Serial No. 47B4921-Up
DRIVE GP-GOVERNOR
7N-4199 DRIVE GP-GOVERNOR
7N4199 WOODWARD GOVERNOR DRIVE GROUP
Serial No. 47B4531-Up
GOVERNOR GP-WOODWARD
7N-9923 GOVERNOR GP-WOODWARD
7N9923 WOODWARD GOVERNOR GROUP--UG8D--Type 1--Part 1
Serial No. 47B4531-Up
Also available as an Attachment at Serial No. 47B3510 to 47B4530 inclusive
8N5069 Controlet Assembly parts are shown on Page 33K
GOVERNOR GP-WOODWARD
7N-9923 GOVERNOR GP-WOODWARD
7N9923 WOODWARD GOVERNOR GORUP--UG8D--Type 1--Part 2
Serial No. 47B4531-Up. Also available as an Attachment at
Serial No. 47B3510 to 47B4530 inclusive
GOVERNOR GP-WOODWARD
7N-9923 GOVERNOR GP-WOODWARD
7N9923 WOODWARD GOVERNOR GROUP--UG8D--Type 2--Part 1
Serial No. 47B4531-Up. Also available as an Attachment at Serial No. 47B3510 to
47B4530 inclusive. 8N5069 Controlet Assembly parts are shown on Page 33K
GOVERNOR GP-WOODWARD
7N-9923 GOVERNOR GP-WOODWARD
7N9923 WOODWARD GOVERNOR GROUP--UG8D--Type 2--Part 2
Serial No. 47B4531-Up
Also available as an Attachment at Serial No. 47B3510 to 47B4530 inclusive
CONTROLET AS
8N-5069 CONTROLET AS
8N5069 CONTROLET ASSEMBLY
Serial No. 47B4531-Up. Also available as an Attachment at Serial No. 47B3510
to 47B4530 inclusive. Part of 7N9923 Woodward Governor Group shown on
Pages 35E & 33G
GOVERNOR GROUP
5L-4917 GOVERNOR GROUP
5L4917 GOVERNOR GROUP--Part 1 of 2
Serial No. 47B409 to 47B586 inclusive
Refer also to Pages 86A, 86B and 87 for special parts
GOVERNOR GROUP
5L-4917 GOVERNOR GROUP
5L4917 GOVERNOR GROUP--Part 2 of 2
Serial No. 47B409 to 47B586 inclusive
GOVERNOR GROUP
5L-4917 GOVERNOR GROUP
5L4917 GOVERNOR GROUP--Part 1 of 2
Serial No. 47B587 to 47B696 inclusive
Refer also to Pages 86A, 86B and 87 for special parts
GOVERNOR GROUP
5L-4917 GOVERNOR GROUP
5L4917 GOVERNOR GROUP--Part 2 of 2
Serial No. 47B587 to 47B696 inclusive
GOVERNOR GROUP
5L-4917 GOVERNOR GROUP
5L4917 GOVERNOR GROUP--Part 1 of 2
Serial No. 47B697 to 47B813 inclusive
Refer also to Pages 86A, 86B and 87 for special parts
GOVERNOR GROUP
5L-4917 GOVERNOR GROUP
5L4917 GOVERNOR GROUP--Part 2 of 2
Serial No. 47B697 to 47B813 inclusive
GOVERNOR GROUP
5L-4917 GOVERNOR GROUP
5L4917 GOVERNOR GROUP--Part 1 of 2
Serial No. 47B814 to 47B1604 inclusive
Refer also to Pages 86A, 86B and 87 for special parts
GOVERNOR GROUP
5L-4917 GOVERNOR GROUP
5L4917 GOVERNOR GROUP--Part 2 of 2
Serial No. 47B814 to 47B1604 inclusive
GOVERNOR GROUP
5L-4917 GOVERNOR GROUP
5L4917 GOVERNOR GROUP--Part 1 of 2
Serial No. 47B1605 to 47B3509 inclusive
Refer also to Pages 86A, 86B and 87 for special parts
GOVERNOR GROUP
5L-4917 GOVERNOR GROUP
5L4917 GOVERNOR GROUP--Part 2 of 2
Serial No. 47B1605 to 47B3509 inclusive
GOVERNOR GROUP
4N-9845 GOVERNOR GROUP
4N9845 GOVERNOR GROUP--Part 1 of 3
Serial No. 47B3510 to 47B3705 inclusive
9S3312 Rack Stop parts are shown on Page 35D
GOVERNOR GROUP
4N-9845 GOVERNOR GROUP
4N9845 GOVERNOR GROUP--Part 2 of 3
Serial No. 47B3510 to 47B3705 inclusive
GOVERNOR GROUP
4N-9845 GOVERNOR GROUP
4N9845 GOVERNOR GROUP--Part 3 of 3
Serial No. 47B3510 to 47B3705 inclusive
GOVERNOR GROUP
4N-9845 GOVERNOR GROUP
4N9845 GOVERNOR GROUP--Part 1 of 3
Serial No. 47B3706 to 47B4018 inclusive
4N4267 Governor Torque Spring parts are shown on Page 35D
GOVERNOR GROUP
4N-9845 GOVERNOR GROUP
4N9845 GOVERNOR GROUP--Part 2 of 3
Serial No. 47B3706 to 47B4018 inclusive
GOVERNOR GROUP
4N-9845 GOVERNOR GROUP
4N9845 GOVERNOR GROUP--Part 3 of 3
Serial No. 47B3706 to 47B4018 inclusive
GOVERNOR GROUP
4N-9845 GOVERNOR GROUP
4N9845 GOVERNOR GROUP--Part 1 of 3
Serial No. 47B4019 to 47B4763 inclusive
4N4267 Governor Torque Spring parts are shown on Page 35D
GOVERNOR GROUP
4N-9845 GOVERNOR GROUP
4N9845 GOVERNOR GROUP--Part 2 of 3
Serial No. 47B4019 to 47B4763 inclusive
GOVERNOR GROUP
4N-9845 GOVERNOR GROUP
4N9845 GOVERNOR GROUP--Part 3 of 3
Serial No. 47B4019 to 47B4763 inclusive
GOVERNOR GP
8N-4859 GOVERNOR GP
8N4859 GOVERNOR GROUP--Part 1 of 4
Serial No. 47B4764 to 47B5097 inclusive
4N4267 Governor Torque Spring parts are shown on Page 35D
GOVERNOR GP
8N-4859 GOVERNOR GP
8N4859 GOVERNOR GROUP--Part 2 of 4
Serial No. 47B4764 to 47B5097 inclusive
GOVERNOR GP
8N-4859 GOVERNOR GP
8N4859 GOVERNOR GROUP--Part 3 of 4
Serial No. 47B4764 to 47B5097 inclusive
GOVERNOR GP
8N-4859 GOVERNOR GP
8N4859 GOVERNOR GROUP--Part 4 of 4
Serial No. 47B4764 to 47B5097 inclusive
GOVERNOR GP
8N-4859 GOVERNOR GP
8N4859 GOVERNOR GROUP--Part 1 of 4
Serial No. 47B5098-Up
4N4267 Governor Torque Spring parts are shown on Page 35D
GOVERNOR GP
8N-4859 GOVERNOR GP
8N4859 GOVERNOR GROUP--Part 2 of 4
Serial No. 47B5098-Up
GOVERNOR GP
8N-4859 GOVERNOR GP
8N4859 GOVERNOR GROUP--Part 3 of 4
Serial No. 47B5098-Up
GOVERNOR GP
8N-4859 GOVERNOR GP
8N4859 GOVERNOR GROUP--Part 4 of 4
Serial No. 47B5098-Up
WOODWARD GOVERNOR GROUP
6N-0111 WOODWARD GOVERNOR GROUP
6N111 WOODWARD GOVERNOR GROUP--Type 1--Part 1 of 2
Serial No. 47B3510-Up
8L8919 Woodward Governor parts are shown on Page 81F
WOODWARD GOVERNOR GROUP
6N-0111 WOODWARD GOVERNOR GROUP
6N111 WOODWARD GOVERNOR GROUP--Type 1--Part 2 of 2
Serial No. 47B3510-Up
WOODWARD GOVERNOR GROUP
6N-0111 WOODWARD GOVERNOR GROUP
6N111 WOODWARD GOVERNOR GROUP--Type 2--Part 1 of 2
Serial No. 47B3510-Up
7N2703 Woodward Governor parts are shown on Pages 81G & 81H
WOODWARD GOVERNOR GROUP
6N-0111 WOODWARD GOVERNOR GROUP
6N111 WOODWARD GOVERNOR GROUP--Type 2--Part 2 of 2
Serial No. 47B3510-Up
GOVERNOR GP-WOODWARD
8L-8919 GOVERNOR GP-WOODWARD
8L8919 WOODWARD GOVERNOR GROUP
Serial No. 47B3510-Up
Part of 6N111 Woodward Governor Group shown on Page 81A
GOVERNOR GP-WOODWARD
7N-2703 GOVERNOR GP-WOODWARD
7N2703 WOODWARD GOVERNOR GROUP--Part 1 of 2
Serial No. 47B3510-Up. Replaced by 7N9923 Woodward Governor Group shown
on Page 33E. Part of 6N111 Woodward Governor Group shown on Page 81C
GOVERNOR GP-WOODWARD
7N-2703 GOVERNOR GP-WOODWARD
7N2703 WOODWARD GOVERNOR GROUP--Part 2 of 2
Serial No. 47B3510-Up
Part of 6N111 Woodward Governor Group shown on Page 81C
DRIVE GP-GOVERNOR
7N-4375 DRIVE GP-GOVERNOR
7N4375 WOODWARD GOVERNOR DRIVE GROUP--Type 1--Part 1 of 2
Serial No. 47B3510 to 47B4530 inclusive. See Page 33D for Woodward Governor
Drive Group used on Serial No. 47B4531-Up
DRIVE GP-GOVERNOR
7N-4375 DRIVE GP-GOVERNOR
7N4375 WOODWARD GOVERNOR DRIVE GROUP--Type 1--Part 2 of 2
Serial No. 47B3510 to 47B4530 inclusive
DRIVE GP-GOVERNOR
7N-4375 DRIVE GP-GOVERNOR
7N4375 WOODWARD GOVERNOR DRIVE GROUP--Type 2--Part 1 of 2
Serial No. 47B3510 to 47B4530 inclusive
See Page 33D for Woodward Governor Drive Group used on Serial No. 47B4531-Up
DRIVE GP-GOVERNOR
7N-4375 DRIVE GP-GOVERNOR
7N4375 WOODWARD GOVERNOR DRIVE GROUP--Type 2--Part 2 of 2
Serial No. 47B3510 to 47B4530 inclusive
GOVERNOR GP
7N-2702 GOVERNOR GP
7N2702 WOODWARD GOVERNOR GROUP--UG8D--110 Volt--Part 1 of 2
GOVERNOR GP
7N-2702 GOVERNOR GP
7N2702 WOODWARD GOVERNOR GROUP--UG8D--110 Volt--Part 2 of 2
ACTUATOR GP-AIR
2N-6006 ACTUATOR GP-AIR
2N6006 AIR ACTUATOR GROUP--Type 2
Serial No. 47B3510-Up
Part of 3N5862 Air Actuated Governor Control Group shown on Page 83B
ACTUATOR GP-AIR
2N-6006 ACTUATOR GP-AIR
AIR ACTUATOR (2N6006 N/S)--Type 1
Serial No. 47B3510-Up
Part of 3N5862 Air Actuated Governor Control Group
GOVERNOR MOUNTING GROUP
6N-1909 GOVERNOR MOUNTING GROUP
6N1909 GOVERNOR MOUNTING GROUP
Serial No. 47B3510-Up
GOVERNOR CONVERSION GROUP
5L-7473 GOVERNOR CONVERSION GROUP
5L7473 GOVERNOR CONVERSION GROUP--10 Percent Regulation at 1300 R.P.M.
GOVERNOR CONVERSION GROUP
5L-7474 GOVERNOR CONVERSION GROUP
5L7474 GOVERNOR CONVERSION GROUP--10 Percent Regulation at 1200-1250
R.P.M.
Serial No. 47B409 to 47B3509 inclusive
GOVERNOR CONVERSION GROUP
5L-9806 GOVERNOR CONVERSION GROUP
5L9806 GOVERNOR CONVERSION GROUP--10 Percent Regulation
Serial No. 47B814-Up
GOVERNOR CONVERSION GROUP
5L-6945 GOVERNOR CONVERSION GROUP
5L6945 GOVERNOR CONVERSION GROUP--3 Percent Regulation at 1200 R.P.M.
Serial No. 47B409 to 47B3509 inclusive
LINES GP-FUEL
FUEL INJECTION VALVES AND LINES GROUP
7M-7423 FUEL INJECTION VALVES AND LINES GROUP
7M7423 FUEL INJECTION VALVES AND LINES GROUP
Serial No. 47B409 to 47B2099 inclusive
FUEL INJECTION VALVES AND LINES GROUP
1N-9848 FUEL INJECTION VALVES AND LINES GROUP
1N9848 FUEL INJECTION VALVES AND LINES GROUP
Serial No. 47B2100 to 47B3509 inclusive
FUEL INJECTION VALVES AND LINES GROUP
7M-7423 FUEL INJECTION VALVES AND LINES GROUP
7M7423 FUEL INJECTION VALVES AND LINES GROUP
Serial No. 47B3510 to 47B4530 inclusive
FUEL INJECTION VALVES AND LINES GROUP
7M-7423 FUEL INJECTION VALVES AND LINES GROUP
7M7423 FUEL INJECTION VALVES AND LINES GROUP
Serial No. 47B4531 to 47B4622 inclusive
PRIMARY FUEL FILTER AND LINES GROUP
5L-1463 PRIMARY FUEL FILTER AND LINES GROUP
5L1463 PRIMARY FUEL FILTER AND LINES GROUP--Type 2
8H7204 Filter parts are shown on Page 101
PRIMARY FUEL FILTER AND LINES GROUP
5L-1463 PRIMARY FUEL FILTER AND LINES GROUP
5L1463 PRIMARY FUEL FILTER AND LINES GROUP--Type 1
FLEXIBLE FUEL LINES GROUP
2L-7786 FLEXIBLE FUEL LINES GROUP
2L7786 FLEXIBLE FUEL LINES GROUP
Only separate parts serviced. When complete Group is required
order 3N6668 shown on Page 102-2
LINES GP-FLEXIBLE FUEL
3N-6668 LINES GP-FLEXIBLE FUEL
3N6668 FLEXIBLE FUEL OIL LINES GROUP-TYPE 1
LINES GP-FLEXIBLE FUEL
3N-6668 LINES GP-FLEXIBLE FUEL
3N6668 FLEXIBLE FUEL OIL LINES GROUP--Type 2
LINES GP-FUEL INJECTION
FUEL INJECTION VALVES AND LINES GROUP
7M-7423 FUEL INJECTION VALVES AND LINES GROUP
7M7423 FUEL INJECTION VALVES AND LINES GROUP
Serial No. 47B409 to 47B2099 inclusive
FUEL INJECTION VALVES AND LINES GROUP
1N-9848 FUEL INJECTION VALVES AND LINES GROUP
1N9848 FUEL INJECTION VALVES AND LINES GROUP
Serial No. 47B2100 to 47B3509 inclusive
FUEL INJECTION VALVES AND LINES GROUP
7M-7423 FUEL INJECTION VALVES AND LINES GROUP
7M7423 FUEL INJECTION VALVES AND LINES GROUP
Serial No. 47B3510 to 47B4530 inclusive
FUEL INJECTION VALVES AND LINES GROUP
7M-7423 FUEL INJECTION VALVES AND LINES GROUP
7M7423 FUEL INJECTION VALVES AND LINES GROUP
Serial No. 47B4531 to 47B4622 inclusive
LINES GP-FUEL INJECTION
8N-3460 LINES GP-FUEL INJECTION
8N3460 FUEL INJECTION LINES GROUP
Serial No. 47B4623 to 47B4767 inclusive
LINES GP-FUEL INJECTION
8N-3460 LINES GP-FUEL INJECTION
8N3460 FUEL INJECTION LINES GROUP
Serial No. 47B4768-Up
PUMP GP-FUEL INJECTION
FUEL PUMP AND GOVERNOR DRIVE GROUP
5H-1117 FUEL PUMP AND GOVERNOR DRIVE GROUP
5H1117 FUEL PUMP AND GOVERNOR DRIVE GROUP
Serial No. 47B409 to 47B3509 inclusive
PUMP GP-FUEL INJECTION
4N-5111 PUMP GP-FUEL INJECTION
4N5111 FUEL PUMP HOUSING GROUP
Serial No. 47B3510-Up
PUMP GP-FUEL PRIMING
PUMP GP-FUEL TFR & PRIMING
3N-0654 PUMP GP-FUEL TFR & PRIMING
3N654 FUEL PRIMING AND TRANSFER PUMP GROUP
Serial No. 47B2727 to 47B4021 inclusive
1P2297 and 3N653 Pump parts are shown on Pages 36B and 36C
PUMP GP-FUEL TFR & PRIMING
3N-0654 PUMP GP-FUEL TFR & PRIMING
3N654 FUEL PRIMING AND TRANSFER PUMP GROUP
Serial No. 47B4022-Up. 8S7705 and 3N653 Pump parts
are shown on Pages 36A-1, 36A-2, 36C-1 & 36C-2
PUMP GP-FUEL PRIMING
8S-7705 PUMP GP-FUEL PRIMING
8S7705 FUEL PRIMING PUMP GROUP
Serial No. 47B4022 to 47B4507 inclusive
Part of 3N654 Fuel Priming and Transfer Pump Group
FUEL PRIMING PUMP BARREL ASSEMBLY
6N-9740 FUEL PRIMING PUMP BARREL ASSEMBLY
6N9740 FUEL PRIMING PUMP BARREL ASSEMBLY
Serial No. 47B2727-Up. Provides Field Replacement for 9S8020
Barrel Assembly shown on Page 36B
PUMP GP-FUEL PRIMING
8S-7705 PUMP GP-FUEL PRIMING
8S7705 FUEL PRIMING PUMP GROUP
Serial No. 47B4508-Up
Part of 3N654 Fuel Priming and Transfer Pump Group shown on Page 36A-1
FUEL PRIMING PUMP ASSEMBLY
1P-2297 FUEL PRIMING PUMP ASSEMBLY
1P2297 FUEL PRIMING PUMP ASSEMBLY
Serial No. 47B2727-Up
Part of 3N654 Fuel Priming and Transfer Pump Group shown on Page 36A
PUMP AS-FUEL PRIMING
2S-0308 PUMP AS-FUEL PRIMING
2S308 FUEL PRIMING PUMP ASSEMBLY
Part of 5L1621 & 8L4943 Fuel Priming Pump Group shown on Page 63B
FUEL PRIMING PUMP GROUP
5L-1621 FUEL PRIMING PUMP GROUP
5L1621 FUEL PRIMING PUMP GROUP--Type 1
Serial No. 47B409 to 47B2328 inclusive. Also part of 5L5433, 5L5434
Electric Starting, Hydraulic Starting & 5L5431 & 5L5432 Air Starting
Arrangements listed on Pages 61, 62, 62B & 63
FUEL PRIMING PUMP GROUP
5L-1621 FUEL PRIMING PUMP GROUP
5L1621 FUEL PRIMING PUMP GROUP--Type 2
Serial No. 47B409 to 47B2328 inclusive. Also part of 5L5433, 5L5434 Electric
Starting, Hydraulic Starting & 5L5431 & 5L5432 Air Starting Arrangements
listed on Pages 61, 62, 62B & 63. 2S308 Pump parts are shown on Page 62A
FUEL PRIMING PUMP GROUP
8L-4943 FUEL PRIMING PUMP GROUP
8L4943 FUEL PRIMING PUMP GROUP
Serial No. 47B2329 to 47B2726 inclusive. Also part of 5L5433, 5L5434
Electric Starting, Hydraulic Starting & 5L5431 & 5L5432 Arrangements
listed on Pages 61, 62, 62B & 63. 2S308 Pump parts are shown on Page 62A
PUMP GP-FUEL TRANSFER
FUEL TRANSFER PUMP ASSEMBLY
4M-9274 FUEL TRANSFER PUMP ASSEMBLY
4M9274 FUEL TRANSFER PUMP ASSEMBLY (4M9180 N/S)
Serial No. 47B470 to 47B2726 inclusive
PUMP GP-FUEL TFR & PRIMING
3N-0654 PUMP GP-FUEL TFR & PRIMING
3N654 FUEL PRIMING AND TRANSFER PUMP GROUP
Serial No. 47B2727 to 47B4021 inclusive
1P2297 and 3N653 Pump parts are shown on Pages 36B and 36C
PUMP GP-FUEL TFR & PRIMING
3N-0654 PUMP GP-FUEL TFR & PRIMING
3N654 FUEL PRIMING AND TRANSFER PUMP GROUP
Serial No. 47B4022-Up. 8S7705 and 3N653 Pump parts
are shown on Pages 36A-1, 36A-2, 36C-1 & 36C-2
PUMP GP-FUEL TRANSFER
3N-0653 PUMP GP-FUEL TRANSFER
3N653 FUEL TRANSFER PUMP ASSEMBLY
Serial No. 47B2727 to 47B4018 inclusive
Part of 3N654 Fuel Priming and Transfer Pump Group shown on Page 36A
PUMP GP-FUEL TRANSFER
3N-0653 PUMP GP-FUEL TRANSFER
3N653 FUEL TRANSFER PUMP ASSEMBLY--Type 1
Serial No. 47B4019-Up
Part of 3N654 Fuel Priming and Transfer Pump Group shown on Pages 36A and 36A-1
PUMP GP-FUEL TRANSFER
3N-0653 PUMP GP-FUEL TRANSFER
3N653 FUEL TRANSFER PUMP ASSEMBLY--Type 2
Serial No. 47B4019-Up
Part of 3N654 Fuel Priming and Transfer Pump Group shown on Pages 36A and 36A-1
FUEL PUMP HOUSING
FUEL PUMP HOUSING
FUEL PUMP HOUSING
SERIAL NO. 47B409 TO 47B539 INCLUSIVE
FUEL PUMP HOUSING
FUEL PUMP HOUSING
FUEL PUMP HOUSING
SERIAL NO. 47B540 TO 47B557 INCLUSIVE
FUEL PUMP HOUSING
FUEL PUMP HOUSING
FUEL PUMP HOUSING
SERIAL NO. 47B558 TO 47B1128 INCLUSIVE
FUEL PUMP HOUSING GROUP
3S-5456 FUEL PUMP HOUSING GROUP
3S5456 FUEL PUMP HOUSING GROUP
Serial No. 47B1129 to 47B3509 inclusive. Only separate parts serviced
SHUTOFF GP
COVER GP
6N-0136 COVER GP
6N136 SHUT-OFF COVER GROUP
Serial No. 47B3510-Up
SAFETY SHUT-OFF GROUP
3N-3293 SAFETY SHUT-OFF GROUP
3N3293 SAFETY SHUT-OFF GROUP-Type 1
Serial No. 47B470 to 47B3509 inclusive
5L1502 Manual Shut-Off and 3N3292 Safety Shut-Off parts are shown on Pages 71P & 71Q through 71R
SAFETY SHUT-OFF GROUP
3N-3293 SAFETY SHUT-OFF GROUP
3N3293 SAFETY SHUT-OFF GROUP--Type 2
Serial No. 47B470 to 47B3509 inclusive
3N7409 Mechanical Shut-Off and 3N3292 Safety Shut-Off parts are shown on Pages 71P & 71Q through 71R
OIL PRESSURE AND OVERSPEED SHUT-OFF GROUP
5L-7252 OIL PRESSURE AND OVERSPEED SHUT-OFF GROUP
5L7252 OIL PRESSURE AND OVERSPEED SHUT-OFF GROUP--Type 1
Serial No. 47B409 to 47B3509 inclusive
5L1502 Shut-Off and 5L1498 Housing Groups are shown on Pages 71P and 71N-2 through 71N-5
OIL PRESSURE AND OVERSPEED SHUT-OFF GROUP
5L-7252 OIL PRESSURE AND OVERSPEED SHUT-OFF GROUP
5L7252 OIL PRESSURE AND OVERSPEED SHUT-OFF GROUP--Type 2
Serial No. 47B409 to 47B3509 inclusive
5L1498 Housing and 3N7409 Mechanical Shut-Off parts are shown on Pages 71N-2 through 71N-5 and 71P
OIL PRESSURE AND OVERSPEED SHUT-OFF GROUP
5L-7252 OIL PRESSURE AND OVERSPEED SHUT-OFF GROUP
5L7252 OIL PRESSURE AND OVERSPEED SHUT-OFF GROUP--Type 3
Serial No. 47B409 to 47B3509 inclusive
4L1498 Housing and 3N7409 Mechanical Shut-Off parts are shown on Pages 71N-2 through 71N-5 and 71P
MANUAL SHUT-OFF GROUP
5L-1502 MANUAL SHUT-OFF GROUP
5L1502 MANUAL SHUT-OFF GROUP
Serial No. 47B470-Up
Part of 3N3293 Safety Shut-Off Group shown on Pages 71M & 71N
SHUT-OFF GP-MAN
3N-3292 SHUT-OFF GP-MAN
3N3292 SAFETY SHUT-OFF GROUP--Type 1--Part 1 of 2
Serial No. 47B470-Up
Part of 3N3293 and 3N5834 Safety Shut-Off Groups shown on Pages 71M, 71N & 71N-a
SHUT-OFF GP-MAN
3N-3292 SHUT-OFF GP-MAN
3N3292 SAFETY SHUT-OFF GROUP--Type 1--Part 2 of 2
Serial No. 47B470-Up
Part of 3N3293 and 3N5834 Safety Shut-Off Groups shown on Pages 71M, 71N and 71N-a
SHUT-OFF GP-MAN
3N-3292 SHUT-OFF GP-MAN
3N3292 SAFETY SHUT-OFF GROUP--Type 2--Part 1 of 2
Serial No. 47B470-Up
Part of 3N3293 and 3N5834 Safety Shut-Off Groups shown on Pages 71M, 71N & 71N-a
SHUT-OFF GP-MAN
3N-3292 SHUT-OFF GP-MAN
3N3292 SAFETY SHUT-OFF GROUP--Type 2--Part 2 of 2
Serial No. 47B470-Up
Part of 3N3293 and 3N5834 Safety Shut-Off Groups shown on Pages 71M, 71N and 71N-a
SHUT-OFF GP-MAN
3N-3292 SHUT-OFF GP-MAN
3N3292 SAFETY SHUT-OFF GROUP--Type 3--Part 1 of 2
Serial No. 47B470-Up
Part of 3N3293, 3N5834 and 5N2931 Safety Shut-Off Groups shown on Pages 71M, 71N, 71N-a, 71N-a1 and 71N-a2
SHUT-OFF GP-MAN
3N-3292 SHUT-OFF GP-MAN
3N3292 SAFETY SHUT-OFF GROUP--Type 3--Part 2 of 2
Serial No. 47B470-Up. Part of 3N3293, 3N5834 and 5N2931 Safety Shut-Off Groups
shown on Pages 71M, 71N, 71N-a, 71N-a1 and 71N-a2
5N-1962 SHUT-OFF ARRANGEMENT
5N1962 SHUT-OFF ARRANGEMENT--1200 RPM
OIL PRESSURE, WATER TEMPERATURE AND OVERSPEED
Serial No. 47B2716-Up
FOR USE WITH MARINE AUXILIARY AND PRESSURIZED COOLING SYSTEM
5N-2941 SHUT-OFF ARRANGEMENT
5N2941 SHUT-OFF ARRANGEMENT
OIL PRESSURE, WATER TEMPERATURE AND OVERSPEED
Serial No. 47B2716-Up
FOR USE WITH MARINE AUXILIARY AND PRESSURIZED COOLING SYSTEM
TORQUE CONTROL GP
RACK STOP GROUP
9S-3312 RACK STOP GROUP
9S3312 RACK STOP GROUP
Serial No. 47B3510 to 47B3705 inclusive
Part of 4N9845 Governor Group shown on Page 35A
TORQUE CONTROL GP
4N-4267 TORQUE CONTROL GP
4N4267 GOVERNOR TORQUE SPRING GROUP
Serial No. 47B3706-Up
Part of 4N9845 & 8N4859 Governor Groups shown on Pages 35C-1 & 35C-8

Information:

(For parts list, see above)

Service Magazine
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05
Engine News
New Diaphragm Used In Fuel Ratio Control
1982/03/17
Improvements Made To Fuel Ratio Control {1278}
1982/12/15
Information For Repair Of Hydraulic Fuel Ratio Controls
1983/08/17
Serviceable Parts For New Fuel Ratio Control; Pressurize Control To Set Rack
1987/05/01
New Spring Used In Fuel Ratio Control
1977/03/15
New Adjustment Pin And Valve Seal Used In Fuel Ratio Control
1977/08/24
Special Instruction
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Specifications
Hydraulic Air-Fuel Ratio Control
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Fuel Ratio Control
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Diaphragm Used In Fuel Ratio Control{1278}
1982/03/15
Improvements Made To Fuel Ratio Control {1278}
1982/11/29
Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15
Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14
New Spring Used In Fuel Ratio Control{1278}
1977/03/21
New Adjustment Pin And Valve Seal Used In Fuel Ratio Control{1278}
1977/07/11
Special Instruction
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Service Magazine
New Diaphragm Used In Fuel Ratio Control{1278}
1982/03/15
Improvements Made To Fuel Ratio Control {1278}
1982/11/29
Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15
Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14
Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05
New Spring Used In Fuel Ratio Control{1278}
1977/03/21
Engine News
New Diaphragm Used In Fuel Ratio Control
1982/03/17
Improvements Made To Fuel Ratio Control {1278}
1982/12/15
Information For Repair Of Hydraulic Fuel Ratio Controls
1983/08/17
Serviceable Parts For New Fuel Ratio Control; Pressurize Control To Set Rack
1987/05/01
New Spring Used In Fuel Ratio Control
1977/03/15
New Adjustment Pin And Valve Seal Used In Fuel Ratio Control
1977/08/24
Special Instruction
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Specifications
Hydraulic Air-Fuel Ratio Control
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Fuel Ratio Control
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Diaphragm Used In Fuel Ratio Control{1278}
1982/03/15
Improvements Made To Fuel Ratio Control {1278}
1982/11/29
Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15
Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14
New Spring Used In Fuel Ratio Control{1278}
1977/03/21
New Adjustment Pin And Valve Seal Used In Fuel Ratio Control{1278}
1977/07/11
Engine News
New Diaphragm Used In Fuel Ratio Control
1982/03/17
Improvements Made To Fuel Ratio Control {1278}
1982/12/15
Information For Repair Of Hydraulic Fuel Ratio Controls
1983/08/17
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct
1986/05/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
Serviceable Parts For New Fuel Ratio Control; Pressurize Control To Set Rack
1987/05/01
New Spring Used In Fuel Ratio Control
1977/03/15
New Adjustment Pin And Valve Seal Used In Fuel Ratio Control
1977/08/24
Special Instruction
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Governor Linkage Adjustments{1264, 1289}
Governor Linkage Adjustments{1264, 1289}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N4904 Printed Circuit Board Conversion Kit For Woodward UG8 Governors{1264, 1289}
Installation Of 8N4904 Printed Circuit Board Conversion Kit For Woodward UG8 Governors{1264, 1289}
Specifications
Governor Linkage Adjustment For UG-8 Governor
D353 INDUSTRIAL & MARINE ENGINES
Governor Air Actuator<BR> (2L6745)
D353 INDUSTRIAL & MARINE ENGINES
Actuator Linkage Adjustment For EG-3P Actuator
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Diaphragm Used In Fuel Ratio Control{1278}
1982/03/15
Improvements Made To Fuel Ratio Control {1278}
1982/11/29
Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15
Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14
Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05
New Spring Used In Fuel Ratio Control{1278}
1977/03/21
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08
Tachometer Drive Shaft Rotation{1085}
1993/08/09
Engine News
How To Adapt The 5P1759 Tachometer Drive Group (Dealer Tool) To D353 Engines Equipped With Electric Hour Meters When Engine RPM Must Be Checked
1979/05/09
Service Magazine
How To Adapt The 5P1759 Tachometer Drive Group (Dealer Tool) To D9H Tractors, 594H Pipelayers And D353 Engines Equipped With Electric Hour Meters When Engine RPM Must Be Checked{0654}
1979/05/14
Tachometer Drive Shaft Rotation{1085}
1993/08/09
Engine News
Improved Fuel Priming Pumps Give Longer Service Life
1979/04/04
Inspect All Engine Oil And Fuel Filter Elements Before Installation
1980/11/12
Improved Fuel Priming Pump Used
1987/05/01
Improved Fuel Priming Pump Assembly Has Better Sealing Characteristics; Repair Kit Available For Knob
1978/03/01
A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1260}
A New Specification Has Been Issued for the Primary Fuel Filter Filtration {1260}
Special Instruction
Installation Of 8N6287 Fuel Priming Knob Kit{1258}
Installation Of 8N6287 Fuel Priming Knob Kit{1258}
Specifications
Fuel Filter
D353 INDUSTRIAL & MARINE ENGINES
Primary Fuel Filter
D353 INDUSTRIAL & MARINE ENGINES
Tool Operating Manual
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
Disassembly and Assembly
Fuel Priming Pump
D353 INDUSTRIAL & MARINE ENGINES
Fuel Priming Pump
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Improved Fuel Priming Pump Assembly Has Better Sealing Characteristics; Repair Kit Available For Knob{1258}
1978/02/27
Do Not Use Plastic Tubing And Compression Fittings Without An Insert As A Fuel Supply Line{1274}
1978/06/26
New Larger Capacity Water Separator Is Available{1250}
1979/03/12
Improved Fuel Priming Pumps Give Longer Service Life{1258}
1979/04/02
Special Instruction
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Service Magazine
Fuel Sulfur Analyzer Available{0651,1280,1318}
1986/01/13
Diesel Fuel Recommendation Expanded{1280}
1977/02/14
High Sulfur Fuel Can Cause Severe Engine Wear And Internal Damage{1280}
1979/02/05
Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27
Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02
Special Instruction
Installation Of 8N9754 Fuel Heater Group{1296}
Installation Of 8N9754 Fuel Heater Group{1296}
Test Sequence for Capsule Type Fuel Nozzles{0782}
Test Sequence for Capsule Type Fuel Nozzles{0782}
Tool Operating Manual
NEHS1126: <NOBR>370-8570</NOBR> Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
Service Magazine
Correct Position Of The Bleed Hole In The Fuel Line Adapter{1252}
1986/04/21
New Spring Used In Fuel Ratio Control{1278}
1977/03/21
New 1U9139 Universal Fuel Line Pickup Available{0775}
1988/05/23
Engine News
Improved Woodward Governor Groups
1979/01/10
New Shaft Assembly Used In Governor Group And New Coupling Assembly Used In Drive Group For Governor And Fuel Injection Pump
1979/08/08
Service Kit Is Available For Woodward UG8 Governor
1979/09/19
CAUTION: Procedure For Adjustment Of Fuel Rack Setting On Hydramechanical Governors Has Been Changed
1980/09/10
Woodward Governor Available For Parallel Generator Applications
1981/04/22
Explanation Of Differences In Timing Advance Information
1981/08/26
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25
New Governor Drive Gears And Weight Assemblies
1983/09/14
Service Information For Woodward Governors
1983/10/26
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint
1983/11/30
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct
1986/05/01
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers
1986/06/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas
1986/10/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
New Spring Used In Fuel Ratio Control
1977/03/15
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Special Instruction
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
&quot;A Series&quot; Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Governor Linkage Adjustments{1264, 1289}
Governor Linkage Adjustments{1264, 1289}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N4904 Printed Circuit Board Conversion Kit For Woodward UG8 Governors{1264, 1289}
Installation Of 8N4904 Printed Circuit Board Conversion Kit For Woodward UG8 Governors{1264, 1289}
Specifications
Fuel Injection Equipment
D353 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump
D353 INDUSTRIAL & MARINE ENGINES
Fuel Pump And Governor Drive
D353 INDUSTRIAL & MARINE ENGINES
Governor<BR> (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Governor<BR> (Later)
D353 INDUSTRIAL & MARINE ENGINES
Governor Drive<BR> (Part of 2N5892 for UG-8 Governor and 1N5403 for EG-3P Actuator)
D353 INDUSTRIAL & MARINE ENGINES
Governor Drive<BR> (Part of 5L7789 for UG-8 Governor and 4N5404 for EG-3P Actuator)
D353 INDUSTRIAL & MARINE ENGINES
Governor Linkage Adjustment For UG-8 Governor
D353 INDUSTRIAL & MARINE ENGINES
Governor Air Actuator<BR> (2L6745)
D353 INDUSTRIAL & MARINE ENGINES
Actuator Linkage Adjustment For EG-3P Actuator
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Fuel Transfer Pump
D353 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump Adapter Housing
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing
D353 INDUSTRIAL & MARINE ENGINES
Governor (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Governor (Later)
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump, Accessory Drive Housing And Governor
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Woodward Governor Available For Parallel Generator Applications{1289,1264}
1981/04/06
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16
Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15
New Governor Drive Gears And Weight Assemblies{1264}
1983/08/22
Service Information For Woodward Governors{0374,1264}
1983/09/26
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14
Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
New Spring Used In Fuel Ratio Control{1278}
1977/03/21
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
Do Not Change Factory Fuel Or Speed Settings On Truck Engines Unless New Settings Are Certified Under Applicable EPA Regulations{0336,0337,1257}
1978/01/30
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16
Improved Woodward Governor Groups{1264,1289}
1979/01/08
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
New Shaft Assembly Used In Governor Group And New Coupling Assembly Used In Drive Group For Governor And Fuel Injection Pump{1264,1288}
1979/07/09
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
Service Kit Is Available For Woodward UG8 Governor{1289}
1979/08/27
Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10
Special Instruction
Installation Of 8N9754 Fuel Heater Group{1296}
Installation Of 8N9754 Fuel Heater Group{1296}
Service Magazine
Fuel Heaters Are Now Available For Field Installation {1296}
1980/01/07
Repair Kit For Diesel Fuel Heater Available {1296}
1983/04/18
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
Engine News
8N1831 Fuel Nozzle Assembly Now Approved For Use In 1693 Truck Engine; Chart For Applications Of 8N1831 And 7N5005 Fuel Nozzle Assemblies
1980/01/23
Inspect All Engine Oil And Fuel Filter Elements Before Installation
1980/11/12
New Fuel Nozzle Test Sheet Available
1982/10/20
Bulged Capsule-Type Fuel Nozzles
1982/10/20
Do Not Use A Wire Brush On Fuel Nozzles
1982/10/20
Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/15
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle
1986/04/01
New Adapter Group For Use With Fuel Injection Test Bench
1977/06/22
New Adjustment Pin And Valve Seal Used In Fuel Ratio Control
1977/08/24
Do Not Use Plastic Tubing And Compression Fittings Without An Insert As A Fuel Supply Line
1978/07/05
New Nozzle Assembly Used In Fuel Injection Valves
1978/08/30
Special Instruction
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Disassembly and Assembly
Fuel Ratio Control
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Valves
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Lines
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17
New Diaphragm Used In Fuel Ratio Control{1278}
1982/03/15
New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach{0651}
1982/05/03
Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27
New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04
Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11
Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22
Improvements Made To Fuel Ratio Control {1278}
1982/11/29
Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15
Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07
Correct Position Of The Bleed Hole In The Fuel Line Adapter{1252}
1986/04/21
Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14
New Spring Used In Fuel Ratio Control{1278}
1977/03/21
New Adapter Group For Use With Fuel Injection Test Bench{0652}
1977/06/13
New Adjustment Pin And Valve Seal Used In Fuel Ratio Control{1278}
1977/07/11
With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
Do Not Use Plastic Tubing And Compression Fittings Without An Insert As A Fuel Supply Line{1274}
1978/06/26
New Nozzle Assembly Used In Fuel Injection Valves{1254}
1978/09/04
New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11
New 1U9139 Universal Fuel Line Pickup Available{0775}
1988/05/23
New Larger Capacity Water Separator Is Available{1250}
1979/03/12
Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23
Fuel Injection Line For Injection Test Bench Is Available From Caterpillar{0652,1250}
1979/07/02
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
Engine News
Do Not Use A Wire Brush On Fuel Nozzles
1982/10/20
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle
1986/04/01
New Nozzle Assembly Used In Fuel Injection Valves
1978/08/30
Special Instruction
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Disassembly and Assembly
Fuel Injection Valves
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Lines
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17
New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach{0651}
1982/05/03
Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27
New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04
Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11
Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07
Correct Position Of The Bleed Hole In The Fuel Line Adapter{1252}
1986/04/21
Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14
With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
New Nozzle Assembly Used In Fuel Injection Valves{1254}
1978/09/04
Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23
Fuel Injection Line For Injection Test Bench Is Available From Caterpillar{0652,1250}
1979/07/02
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
Do Not Reuse the Hold Down Bolts for the Fuel Injectors On All Products that Contain C9 Through C32 Engines {1290}
2014/08/14
New Diaphragm Used In Fuel Ratio Control{1278}
1982/03/15
Improvements Made To Fuel Ratio Control {1278}
1982/11/29
Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15
Remanufactured Air Fuel Ratio Controls {1278,7754}
1985/01/14
New Spring Used In Fuel Ratio Control{1278}
1977/03/21
New Adjustment Pin And Valve Seal Used In Fuel Ratio Control{1278}
1977/07/11
Self-Powered Hour Meters Available{7480,7450}
1987/02/16
Polarity Connections And Use Of Service Meter Films When Service Meter Kits Are Installed{7480,7000}
1987/02/16
Fuse And Wire Assembly Is Available For Protection Of Earlier 6N5906 Service Meters{7480}
1979/01/29
More Potting Material Now Used In 6N5906 Electric Service Meter{7480}
1979/11/26
Engine News
Improved Woodward Governor Groups
1979/01/10
Improved Fuel Priming Pumps Give Longer Service Life
1979/04/04
New Shaft Assembly Used In Governor Group And New Coupling Assembly Used In Drive Group For Governor And Fuel Injection Pump
1979/08/08
Service Kit Is Available For Woodward UG8 Governor
1979/09/19
Fuel Heaters Are Now Available For Field Installation
1980/01/09
8N1831 Fuel Nozzle Assembly Now Approved For Use In 1693 Truck Engine; Chart For Applications Of 8N1831 And 7N5005 Fuel Nozzle Assemblies
1980/01/23
CAUTION: Procedure For Adjustment Of Fuel Rack Setting On Hydramechanical Governors Has Been Changed
1980/09/10
Inspect All Engine Oil And Fuel Filter Elements Before Installation
1980/11/12
Explanation Of Differences In Timing Advance Information
1981/08/26
New Diaphragm Used In Fuel Ratio Control
1982/03/17
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers
1986/03/01
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers
1986/06/01
Changes Have Been Made To 0T Microfiche (Fuel Setting And Related Information)
1986/07/01
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas
1986/10/01
New Spring Used In Fuel Ratio Control
1977/03/15
New Adapter Group For Use With Fuel Injection Test Bench
1977/06/22
New Adjustment Pin And Valve Seal Used In Fuel Ratio Control
1977/08/24
Improved Fuel Priming Pump Assembly Has Better Sealing Characteristics; Repair Kit Available For Knob
1978/03/01
New Nozzle Assembly Used In Fuel Injection Valves
1978/08/30
Special Instruction
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Installation Of 8N4904 Printed Circuit Board Conversion Kit For Woodward UG8 Governors{1264, 1289}
Installation Of 8N4904 Printed Circuit Board Conversion Kit For Woodward UG8 Governors{1264, 1289}
Installation Of 8N6287 Fuel Priming Knob Kit{1258}
Installation Of 8N6287 Fuel Priming Knob Kit{1258}
Specifications
Fuel Injection Equipment
D353 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump
D353 INDUSTRIAL & MARINE ENGINES
Fuel Pump And Governor Drive
D353 INDUSTRIAL & MARINE ENGINES
Fuel Filter
D353 INDUSTRIAL & MARINE ENGINES
Governor<BR> (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Governor<BR> (Later)
D353 INDUSTRIAL & MARINE ENGINES
Primary Fuel Filter
D353 INDUSTRIAL & MARINE ENGINES
Governor Drive<BR> (Part of 2N5892 for UG-8 Governor and 1N5403 for EG-3P Actuator)
D353 INDUSTRIAL & MARINE ENGINES
Governor Drive<BR> (Part of 5L7789 for UG-8 Governor and 4N5404 for EG-3P Actuator)
D353 INDUSTRIAL & MARINE ENGINES
Governor Linkage Adjustment For UG-8 Governor
D353 INDUSTRIAL & MARINE ENGINES
Governor Air Actuator<BR> (2L6745)
D353 INDUSTRIAL & MARINE ENGINES
Actuator Linkage Adjustment For EG-3P Actuator
D353 INDUSTRIAL & MARINE ENGINES
Disassembly and Assembly
Fuel Priming Pump
D353 INDUSTRIAL & MARINE ENGINES
Fuel Priming Pump
D353 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump
D353 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump Adapter Housing
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing
D353 INDUSTRIAL & MARINE ENGINES
Fuel Ratio Control
D353 INDUSTRIAL & MARINE ENGINES
Governor (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Governor (Later)
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump, Accessory Drive Housing And Governor
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Valves
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Fuel Heaters Are Now Available For Field Installation {1296}
1980/01/07
Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17
New Dual Speed Switch Is Now Available{7418,7410,7411,1400}
1981/09/21
New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23
New Diaphragm Used In Fuel Ratio Control{1278}
1982/03/15
Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine{0651,0654,1250}
1982/03/22
Lubricant Recommendations Changed For All Caterpillar Engines To Combat Effects Of Fuel Sulfur{1318,0375,0374,1280}
1982/05/03
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16
Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27
New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04
Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11
Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22
Improved Mounting Assembly For Speed Switch Contactor Group{7418}
1983/01/17
Information For Repair Of Hydraulic Fuel Ratio Controls{1278}
1983/08/15
New Governor Drive Gears And Weight Assemblies{1264}
1983/08/22
Service Information For Woodward Governors{0374,1264}
1983/09/26
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27
Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03
Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01
Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Engine Information Plate Contains More Data; Use Of Performance Specifications{1250,7557}
1985/10/28
Fuel Sulfur Analyzer Available{0651,1280,1318}
1986/01/13
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07
Three Element Speed Switch Replaces Dual Element Speed Switch{7418,7411,7410,7421}
1986/04/21
Correct Position Of The Bleed Hole In The Fuel Line Adapter{1252}
1986/04/21
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05
Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10
Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14
Diesel Fuel Recommendation Expanded{1280}
1977/02/14
New Spring Used In Fuel Ratio Control{1278}
1977/03/21
New Adapter Group For Use With Fuel Injection Test Bench{0652}
1977/06/13
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08
With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
Improved Fuel Priming Pump Used{1258}
1987/04/20
Black Light Leak Detection Kit Available For Oil, Fuel and Cooling Systems {0774,1250,1300,1350}
1987/05/11
Do Not Change Factory Fuel Or Speed Settings On Truck Engines Unless New Settings Are Certified Under Applicable EPA Regulations{0336,0337,1257}
1978/01/30
Probable Causes Of Low Fuel Delivery During Testing On Fuel Injection Test Benches{0650,1250}
1978/02/06
Improved Fuel Priming Pump Assembly Has Better Sealing Characteristics; Repair Kit Available For Knob{1258}
1978/02/27
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
Do Not Use Plastic Tubing And Compression Fittings Without An Insert As A Fuel Supply Line{1274}
1978/06/26
New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}
1978/09/25
Caterpillar Fuel Injection Test Bench Book{0374}
1978/10/16
Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16
New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04
Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18
New 1U9139 Universal Fuel Line Pickup Available{0775}
1988/05/23
Improved Woodward Governor Groups{1264,1289}
1979/01/08
Fuse And Wire Assembly Is Available For Protection Of Earlier 6N5906 Service Meters{7480}
1979/01/29
High Sulfur Fuel Can Cause Severe Engine Wear And Internal Damage{1280}
1979/02/05
Improved Fuel Priming Pumps Give Longer Service Life{1258}
1979/04/02
How To Adapt The 5P1759 Tachometer Drive Group (Dealer Tool) To D9H Tractors, 594H Pipelayers And D353 Engines Equipped With Electric Hour Meters When Engine RPM Must Be Checked{0654}
1979/05/14
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
New Shaft Assembly Used In Governor Group And New Coupling Assembly Used In Drive Group For Governor And Fuel Injection Pump{1264,1288}
1979/07/09
Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27
Service Kit Is Available For Woodward UG8 Governor{1289}
1979/08/27
More Potting Material Now Used In 6N5906 Electric Service Meter{7480}
1979/11/26
Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
Tachometer Drive Shaft Rotation{1085}
1993/08/09
Special Instruction
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Service Magazine
Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17
Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27
New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04
Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11
Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07
Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14
New Adapter Group For Use With Fuel Injection Test Bench{0652}
1977/06/13
With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
New Nozzle Assembly Used In Fuel Injection Valves{1254}
1978/09/04
New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11
Special Instruction
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Test Sequence for Capsule Type Fuel Nozzles{0782}
Test Sequence for Capsule Type Fuel Nozzles{0782}
Engine News
Improved Woodward Governor Groups
1979/01/10
New Shaft Assembly Used In Governor Group And New Coupling Assembly Used In Drive Group For Governor And Fuel Injection Pump
1979/08/08
Service Kit Is Available For Woodward UG8 Governor
1979/09/19
8N1831 Fuel Nozzle Assembly Now Approved For Use In 1693 Truck Engine; Chart For Applications Of 8N1831 And 7N5005 Fuel Nozzle Assemblies
1980/01/23
CAUTION: Procedure For Adjustment Of Fuel Rack Setting On Hydramechanical Governors Has Been Changed
1980/09/10
Woodward Governor Available For Parallel Generator Applications
1981/04/22
Explanation Of Differences In Timing Advance Information
1981/08/26
New Fuel Nozzle Test Sheet Available
1982/10/20
Bulged Capsule-Type Fuel Nozzles
1982/10/20
Do Not Use A Wire Brush On Fuel Nozzles
1982/10/20
Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/15
New Governor Drive Gears And Weight Assemblies
1983/09/14
Service Information For Woodward Governors
1983/10/26
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle
1986/04/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
New Adapter Group For Use With Fuel Injection Test Bench
1977/06/22
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
New Nozzle Assembly Used In Fuel Injection Valves
1978/08/30
Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01
Special Instruction
&quot;A Series&quot; Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Use Of 6V-4180 Timing Fixture Group To Check Off-Engine Timing Dimension Setting{1251, 0653}
Use Of 6V-4180 Timing Fixture Group To Check Off-Engine Timing Dimension Setting{1251, 0653}
Governor Linkage Adjustments{1264, 1289}
Governor Linkage Adjustments{1264, 1289}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N4904 Printed Circuit Board Conversion Kit For Woodward UG8 Governors{1264, 1289}
Installation Of 8N4904 Printed Circuit Board Conversion Kit For Woodward UG8 Governors{1264, 1289}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Specifications
Fuel Injection Equipment
D353 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump
D353 INDUSTRIAL & MARINE ENGINES
Fuel Pump And Governor Drive
D353 INDUSTRIAL & MARINE ENGINES
Governor<BR> (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Governor<BR> (Later)
D353 INDUSTRIAL & MARINE ENGINES
Governor Drive<BR> (Part of 2N5892 for UG-8 Governor and 1N5403 for EG-3P Actuator)
D353 INDUSTRIAL & MARINE ENGINES
Governor Drive<BR> (Part of 5L7789 for UG-8 Governor and 4N5404 for EG-3P Actuator)
D353 INDUSTRIAL & MARINE ENGINES
Governor Linkage Adjustment For UG-8 Governor
D353 INDUSTRIAL & MARINE ENGINES
Governor Air Actuator<BR> (2L6745)
D353 INDUSTRIAL & MARINE ENGINES
Actuator Linkage Adjustment For EG-3P Actuator
D353 INDUSTRIAL & MARINE ENGINES
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Disassembly and Assembly
Fuel Transfer Pump
D353 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump Adapter Housing
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing
D353 INDUSTRIAL & MARINE ENGINES
Governor (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Governor (Later)
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump, Accessory Drive Housing And Governor
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Valves
D353 INDUSTRIAL & MARINE ENGINES
Rocker Shaft Assembly And Push Rods
D353 INDUSTRIAL & MARINE ENGINES
Rocker Shaft Assembly
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Woodward Governor Available For Parallel Generator Applications{1289,1264}
1981/04/06
Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17
New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach{0651}
1982/05/03
Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27
New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04
Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11
Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22
New Governor Drive Gears And Weight Assemblies{1264}
1983/08/22
Service Information For Woodward Governors{0374,1264}
1983/09/26
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Valve Lash Adjustment Not A Warranty Item {1102,1105}
1985/01/14
Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
New Tie Bars Improve Stability Of The Fuel Injection Test Bench{0652}
1977/01/17
Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14
New Adapter Group For Use With Fuel Injection Test Bench{0652}
1977/06/13
With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31
Probable Causes Of Low Fuel Delivery During Testing On Fuel Injection Test Benches{0650,1250}
1978/02/06
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
New Nozzle Assembly Used In Fuel Injection Valves{1254}
1978/09/04
New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}
1978/09/25
Caterpillar Fuel Injection Test Bench Book{0374}
1978/10/16
New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04
Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18
Improved Woodward Governor Groups{1264,1289}
1979/01/08
Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
Fuel Injection Line For Injection Test Bench Is Available From Caterpillar{0652,1250}
1979/07/02
New Shaft Assembly Used In Governor Group And New Coupling Assembly Used In Drive Group For Governor And Fuel Injection Pump{1264,1288}
1979/07/09
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
Service Kit Is Available For Woodward UG8 Governor{1289}
1979/08/27
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
Do Not Reuse the Hold Down Bolts for the Fuel Injectors On All Products that Contain C9 Through C32 Engines {1290}
2014/08/14
Engine News
Improved Fuel Priming Pumps Give Longer Service Life
1979/04/04
Improved Fuel Priming Pump Used
1987/05/01
Improved Fuel Priming Pump Assembly Has Better Sealing Characteristics; Repair Kit Available For Knob
1978/03/01
Special Instruction
Installation Of 8N6287 Fuel Priming Knob Kit{1258}
Installation Of 8N6287 Fuel Priming Knob Kit{1258}
Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System{1258}
Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System{1258}
Disassembly and Assembly
Fuel Priming Pump
D353 INDUSTRIAL & MARINE ENGINES
Fuel Priming Pump
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Improved Fuel Priming Pump Used{1258}
1987/04/20
Improved Fuel Priming Pump Assembly Has Better Sealing Characteristics; Repair Kit Available For Knob{1258}
1978/02/27
Do Not Use Plastic Tubing And Compression Fittings Without An Insert As A Fuel Supply Line{1274}
1978/06/26
New Larger Capacity Water Separator Is Available{1250}
1979/03/12
Improved Fuel Priming Pumps Give Longer Service Life{1258}
1979/04/02
Special Instruction, REHS1037 , "Installation Instructions for the Electric Fuel Priming Pump on Caterpillar Equipment With the 24 Volt System" has been Revised {1258}
2004/03/29
Engine News
Improved Woodward Governor Groups
1979/01/10
New Shaft Assembly Used In Governor Group And New Coupling Assembly Used In Drive Group For Governor And Fuel Injection Pump
1979/08/08
Service Kit Is Available For Woodward UG8 Governor
1979/09/19
CAUTION: Procedure For Adjustment Of Fuel Rack Setting On Hydramechanical Governors Has Been Changed
1980/09/10
Woodward Governor Available For Parallel Generator Applications
1981/04/22
Explanation Of Differences In Timing Advance Information
1981/08/26
New Governor Drive Gears And Weight Assemblies
1983/09/14
Service Information For Woodward Governors
1983/10/26
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Special Instruction
&quot;A Series&quot; Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Governor Linkage Adjustments{1264, 1289}
Governor Linkage Adjustments{1264, 1289}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N4904 Printed Circuit Board Conversion Kit For Woodward UG8 Governors{1264, 1289}
Installation Of 8N4904 Printed Circuit Board Conversion Kit For Woodward UG8 Governors{1264, 1289}
Installation Of 8N6287 Fuel Priming Knob Kit{1258}
Installation Of 8N6287 Fuel Priming Knob Kit{1258}
Specifications
Fuel Injection Equipment
D353 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump
D353 INDUSTRIAL & MARINE ENGINES
Fuel Pump And Governor Drive
D353 INDUSTRIAL & MARINE ENGINES
Governor<BR> (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Governor<BR> (Later)
D353 INDUSTRIAL & MARINE ENGINES
Governor Drive<BR> (Part of 2N5892 for UG-8 Governor and 1N5403 for EG-3P Actuator)
D353 INDUSTRIAL & MARINE ENGINES
Governor Drive<BR> (Part of 5L7789 for UG-8 Governor and 4N5404 for EG-3P Actuator)
D353 INDUSTRIAL & MARINE ENGINES
Governor Linkage Adjustment For UG-8 Governor
D353 INDUSTRIAL & MARINE ENGINES
Governor Air Actuator<BR> (2L6745)
D353 INDUSTRIAL & MARINE ENGINES
Actuator Linkage Adjustment For EG-3P Actuator
D353 INDUSTRIAL & MARINE ENGINES
Tool Operating Manual
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
Disassembly and Assembly
Fuel Transfer Pump
D353 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump Adapter Housing
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing
D353 INDUSTRIAL & MARINE ENGINES
Governor (Earlier)
D353 INDUSTRIAL & MARINE ENGINES
Governor (Later)
D353 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump, Accessory Drive Housing And Governor
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
Woodward Governor Available For Parallel Generator Applications{1289,1264}
1981/04/06
New Governor Drive Gears And Weight Assemblies{1264}
1983/08/22
Service Information For Woodward Governors{0374,1264}
1983/09/26
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
Improved Fuel Priming Pump Used{1258}
1987/04/20
Improved Fuel Priming Pump Assembly Has Better Sealing Characteristics; Repair Kit Available For Knob{1258}
1978/02/27
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Improved Woodward Governor Groups{1264,1289}
1979/01/08
Improved Fuel Priming Pumps Give Longer Service Life{1258}
1979/04/02
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
New Shaft Assembly Used In Governor Group And New Coupling Assembly Used In Drive Group For Governor And Fuel Injection Pump{1264,1288}
1979/07/09
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
Service Kit Is Available For Woodward UG8 Governor{1289}
1979/08/27
Special Instruction
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Installation of 7C9760 (12V) or 8N3569 (24V) Fuel Boost Pump Group{1250, 1256, 1260}
Service Magazine
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
Do Not Change Factory Fuel Or Speed Settings On Truck Engines Unless New Settings Are Certified Under Applicable EPA Regulations{0336,0337,1257}
1978/01/30
Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16
Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10
Disassembly and Assembly
Water Temperature Regulators
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Larger Capacity Water Separator Is Available{1250}
1979/03/12
Engine News
New Service Meter Used In Mechanical Shutoff Group
1981/07/01
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Specifications
Mechanical Safety Shutoff
D353 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Service Meter Used In Mechanical Shutoff Group{7478}
1981/06/01
New Dual Speed Switch Is Now Available{7418,7410,7411,1400}
1981/09/21
Improved Mounting Assembly For Speed Switch Contactor Group{7418}
1983/01/17
Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04
Three Element Speed Switch Replaces Dual Element Speed Switch{7418,7411,7410,7421}
1986/04/21
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05
Correct Position Of The Bleed Hole In The Fuel Line Adapter{1252}
1986/04/21
New 1U9139 Universal Fuel Line Pickup Available{0775}
1988/05/23
Tool Operating Manual
NEHS1126: <NOBR>370-8570</NOBR> Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
Service Magazine
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08
Be Sure The Polarity Of The Electrical Connector On EG3P Woodward Actuator Assembly Is Correct{1265,1250}
1986/05/05
Engine News
Changes To 9S240 Rack Position Tool Group; Revision To Special Instructions
1980/05/14
New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach
1982/05/12
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25
Service Information For Easier Use Of The 6V3100 Timing Indicator Group
1982/10/20
Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/15
New Service Centers For 6V3100 Engine Timing Indicator Group
1983/10/26
Fuel Sulfur Analyzer Available
1986/01/01
New Engine Timing Indicator Group Available
1986/07/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups
1987/03/01
New Adapter Group For Use With Fuel Injection Test Bench
1977/06/22
Special Instruction
Troubleshooting And Repair Of The 5P2160 Engine Horsepower Meter Arrangement<SUP><FONT SIZE=-1>*</FONT></SUP>{0781, 0782}
Troubleshooting And Repair Of The 5P2160 Engine Horsepower Meter Arrangement*{0781, 0782}
Using The 5P2160 Engine Horsepower Meter Arrangement<SUP><FONT SIZE=-1>*</FONT></SUP>{0781, 0782}
Using The 5P2160 Engine Horsepower Meter Arrangement*{0781, 0782}
Troubleshooting And Repair Of The 1P3500 And 2P8280 Injection Timing Groups{0782}
Troubleshooting And Repair Of The 1P3500 And 2P8280 Injection Timing Groups{0782}
Installation Of 6V124 Drive Coupling Modification Kit{0650, 0706, 1250}
Installation Of 6V124 Drive Coupling Modification Kit{0650, 0706, 1250}
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4950 Injection Line Speed Pickup Group{0782}
Using The 6V4950 Injection Line Speed Pickup Group{0782}
Electronic Repair Of 6V3100 Diesel Engine Timing Indicator{0651, 1250}
Electronic Repair Of 6V3100 Diesel Engine Timing Indicator{0651, 1250}
Use And Repair Of The 6V7925 Fuel Rate Indicator{0782}
Use And Repair Of The 6V7925 Fuel Rate Indicator{0782}
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}
Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}
Using The 8T1000 Position Indicator Group{0760, 0762}
Using The 8T1000 Position Indicator Group{0760, 0762}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Technical Information Bulletin
368-9910 Multi-Tool Group with the 368-9911 Burn Rate Group Accuracy Issue{0599, 0701, 0702, 0706, 1000, 7610, 7620}
368-9910 Multi-Tool Group with the 368-9911 Burn Rate Group Accuracy Issue{0599, 0701, 0702, 0706, 1000, 7610, 7620}
Tool Operating Manual
Using the Caterpillar Fuel Flow Monitor System{0782, 1000, 1250}
Using the Caterpillar Fuel Flow Monitor System{0782, 1000, 1250}
9U-7840 Fuel Injection Equipment Calibration Fluid Test Kit{0374, 0599, 0706}
9U-7840 Fuel Injection Equipment Calibration Fluid Test Kit{0374, 0599, 0706}
NEHS1126: <NOBR>370-8570</NOBR> Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
NEHS1111: 368-9910 Multi-Tool Group 3 {0599, 0701, 0702, 0706, 1000, 7610, 7620}
NEHS1111: 368-9910 Multi-Tool Group 3 {0599, 0701, 0702, 0706, 1000, 7610, 7620}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
Service Magazine
Changes To 9S240 Rack Position Tool Group; Revision To Special Instructions{0653,0374,1250}
1980/05/05
Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16
Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11
Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27
Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03
Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07
Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16
New Engine Timing Indicator Group Available {0781,0782}
1986/07/07
Fabricated Extension Prevents Fuel &quot;Splash&quot; During Injection Valve Testing{0650,1254}
1977/10/17
With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
The Caterpillar Fuel Flow Monitor System Available {0782,1000,1250}
1987/05/11
Two New Self-Powered Digital Tachometers And Signal Generator Available {7462}
1987/05/11
5P4149 Conversion Group To Become A Discontinued Item On October 1, 1978{0650,1254}
1978/03/27
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
Four New Contact Points Added To 5P6524 Engine Timing Indicator Group{0653}
1978/08/07
New 5P8744 Adapter Assembly And Special Instruction Procedures For 5P4150 Nozzle Tester Group{0650}
1978/08/28
4J7533 O-Ring Seals Now Available For Parts Service Of The 5P4150 Nozzle Tester Group{0651}
1978/10/09
Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16
New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04
Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18
New 1U9139 Universal Fuel Line Pickup Available{0775}
1988/05/23
Improved Pressure Gauge Sender Used{7450,7485}
1988/11/21
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
6V183 Gasket Now Available For Parts Service To Use On 5P4150 Or 8S2242 Nozzle Tester{0651}
1979/06/25
Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}
1979/09/03
Fast Fuel Delivery Couplings And Fast Oil Change Couplings Are Available For All Caterpillar Equipment{0671,1273,1279,1325}
1979/10/08
Engine News
CAUTION: Procedure For Adjustment Of Fuel Rack Setting On Hydramechanical Governors Has Been Changed
1980/09/10
Special Instruction
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Service Magazine
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
Do Not Change Factory Fuel Or Speed Settings On Truck Engines Unless New Settings Are Certified Under Applicable EPA Regulations{0336,0337,1257}
1978/01/30
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10
New Adjustment Pin And Valve Seal Used In Fuel Ratio Control{1278}
1977/07/11
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08

Truck sale:

CAT D353E
USD $22,500 
CAT D353E

Contractor Sales
Pocatello, Idaho
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.