CRANKSHAFT BEARING REPLACEMENT GROUP D4D TRACK-TYPE TRACTOR

Pos.	Part No	Qty	Parts name
1.	5S-9017	[1]	PISTON ASSEM.
2.	7S-8378	[1]	RING (Top)
3.	5S-6750	[1]	RING (Intermediate)
4.	9S-7788	[1]	RING (Oil)
			(Parts of 5S9017 Piston Assem.)
5.	7M-7821	[1]	BEARING (Standard)
	2S-0502	[1]	BEARING (.010"Undersize)
	2S-0503	[1]	BEARING (.020"Undersize)
	7M-7826	[1]	BEARING (.030"Undersize)
6.	5S-6360	[1]	ROD ASSEM.
	7S-9347	[1]	BEARING
7.	1P-9956	[2]	BOLT
8.	5S-6348	[2]	NUT
			(Parts of 5S6360 Rod Assem.)
9.	9H-4016	[1]	PIN
10.	9H-4015	[2]	RETAINER
	7S-9404	[1]	RING GROUP
			(Consists of complete set of Rings FOR ONE PISTON)

#UE0701210058

5S-6428: CAMSHAFT

CAMSHAFT

CAMSHAFT (5S6428 N/S)

c102416 UE070121

For full view, you need register

Parts for your D4D TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	5S-3971	[1]	CAMSHAFT
2.	0S-0509	[2]	BOLT
3.	8S-1491	[1]	LOCK
4.	5S-3804	[1]	GEAR (80 Teeth)
5.	0S-1748	[4]	BOLT
6.	8S-2630	[1]	LOCK
7.	7S-2204	[1]	WASHER

#UE0701210059

5S-8056: ACCESSORY DRIVE AND PRIMARY FUEL FILTER

ACCESSORY DRIVE AND PRIMARY FUEL FILTER

ACCESSORY DRIVE AND PRIMARY FUEL FILTER (5S8056 N/S)

c112403 UE070121

5S8056 ACCESSORY DRIVE AND PRIMARY FUEL FILTER Parts scheme

For full view, you need register

Parts for your D4D TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	1B-9575	[ 2]	BOLT
2.	3B-4505	[ 7]	LOCKWASHER
3.	8H-9220	[ 1]	GASKET
4.	7S-5045	[ 1]	HOUSING ASSEM.
5.	9F-2247	[ 1]	PLUG
6.	2H-1190	[ 2]	DOWEL
7.	5M-6214	[ 2]	PLUG
8.	2D-6642	[ 1]	BALL
9.	2A-3348	[ 1]	DOWEL
10.	8H-9788	[ 1]	GASKET
11.	8H-9787	[ 1]	COVER
12.	1A-9136	[ 2]	BOLT
13.	8H-9364	[ 1]	GASKET
14.	7S-5047	[ 1]	SHAFT
15.	8H-9789	[ 1]	BEARING
16.	8H-9718	[ 1]	RETAINER
17.	7M-9763	[ 2]	LOCK
18.	0S-1594	[ 4]	BOLT
19.	5S-3828	[ 1]	SLEEVE
20.	5S-7614	[ 1]	GEAR (80 Teeth)
21.	7S-9847	[ 1]	WASHER
22.	9S-1313	[ 1]	NUT
23.	2H-3755	[ 2]	BOLT
24.	2F-6156	[ 1]	LOCK
25.	5S-7612	[ 1]	PLATE
26.	5S-7660	[ 1]	GEAR ASSEM. (57 Teeth)
27.	5S-7630	[ 1]	BEARING
28.	5B-9079	[ 1]	NUT
29.	0L-1351	[ 2]	BOLT
30.	5S-7611	[ 1]	LOCK
31.	5S-7608	[ 1]	SHAFT
32.	9H-2769	[ 1]	BOWL
33.	9H-2770	[ 1]	GASKET
34.	5S-7645	[ 1]	ELEMENT ASSEM.
35.	4D-0322	[ 1]	BAIL ASSEM.
36.	0S-1618	[ 3]	BOLT
37.	9L-2796	[ 1]	BOLT

Information:

BASIC ENGINE

CRANKSHAFT GP

Special Instruction

Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}

Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}
Installation Of Crankshaft Seals And Wear Sleeves{1160, 1161}

Installation Of Crankshaft Seals And Wear Sleeves{1203}
Installation Of Crankshaft Seals And Wear Sleeves{1203}

Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}

Installation Of Service Replacement Crankshaft For A 3304 Or 3306 Engine{1202}
Installation Of Service Replacement Crankshaft For A 3304 Or 3306 Engine{1202}

Crankshaft Seal And Wear Sleeve Installation{1160, 1161}
Crankshaft Seal And Wear Sleeve Installation{1160, 1161}

Installation Of Seal Groups With Hydrodynamic Grooves In The Seal Lip{1160, 1161}
Installation Of Seal Groups With Hydrodynamic Grooves In The Seal Lip{1160, 1161}

Specifications

Crankshaft
3304 VEHICULAR ENGINE

Bearing Surface (Journal) For Main Bearings
3304 VEHICULAR ENGINE

Bearing Surface (Journal) For Connecting Rods
3304 VEHICULAR ENGINE

Main Bearings And Connecting Rod Bearings
3304 VEHICULAR ENGINE

Crankshaft Hub
3304 VEHICULAR ENGINE

Tool Operating Manual

9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}

420-7630 Main Bearing Cap Lifting Device{0599, 0629, 0632, 0701, 1201, 1203, 1230}
420-7630 Main Bearing Cap Lifting Device{0599, 0629, 0632, 0701, 1201, 1203, 1230}

Reuse And Salvage Guidelines

Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}

Reuse and Salvage for Crankshafts {0674, 1202}
Reuse and Salvage for Crankshafts {0674, 1202}

Visual Inspection of Main Bearings and Connecting Rod Bearings {1202, 1203, 1225, 1230}
Visual Inspection of Main Bearings and Connecting Rod Bearings {1202, 1203, 1225, 1230}

9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}
9U-5132 Timing and Fuel System Setting Tool Group{1105, 1162, 1290, 1905}

Reuse and Salvage for Engine Dampers {1202, 1205}
Reuse and Salvage for Engine Dampers {1202, 1205}

Disassembly and Assembly

Vibration Damper And Pulley
D4 TRACTOR ENGINE

Crankshaft Front Seal
D4 TRACTOR ENGINE

Crankshaft Main Bearings
D4 TRACTOR ENGINE

Crankshaft Rear Seal
D4 TRACTOR ENGINE

Crankshaft
D4 TRACTOR ENGINE

Service Magazine

Engine Storage; Engine Start-Up After Storage{1000}
1982/02/22

Use 6V6035 Hardness Tester On Crankshafts{0651,1202}
1982/02/22

Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/03

New Crankshaft Assemblies{1202,1204,1206,1207,1212}
1982/11/01

6V6142 And 6V6143 Installers Can Be Used To Install Crankshaft Seals And Wear Sleeves{0622,0626,1160,1161}
1982/11/01

Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16

Reuse Of Engine Bearings{1230}
1983/05/16

Crankshaft Failures{1202,1230}
1983/11/21

Reuse Of Engine Bearings{1230,1219,1203}
1983/11/21

Remanufactured Undersize Crankshafts Are Available{1202}
1983/11/21

Installing New Copper Bonded Bearings Can Extend Engine Life{1230,1203,1219}
1985/04/29

Remanufactured Crankshafts Are Available In Standard And Two Undersize Dimensions (U.S. and Canada){1202,7754}
1985/11/18

Bearing Failures On Engines Due To Lack Of Lubrication{1230,1219,1203,1202}
1986/09/08

Tools To Remove Wear Sleeves From Crankshafts{0621,7558}
1977/04/18

New Seal For Crankshaft{1161}
1977/07/04

Tools To Install Crankshaft Seal And Wear Sleeve{1160,1161,0622}
1977/07/11

Crankshaft Support Groups Are Available To Measure Bent Crankshafts{0653,1202}
1977/11/07

Double Lip Seal With Hydrodynamic Grooves Used At Rear Of Crankshaft {1161,1200}
1987/09/28

Use New Main Bearings In Replacement Cylinder Blocks{1203,1201}
1978/06/12

Change In Procedure To Check Main Bearing Clearance{1203}
1978/08/28

Four Crankshaft Rear Seals Are Available For Use On 3304 And 3306 Engines{1161}
1979/03/26

Check Crankshaft Seals During Installation Of Engine Overhaul Gasket Kits; Add A Wear Sleeve When Needed{7555,7558,1161}
1979/06/04

New Centering Rings For Oversized Main Bearings{0665,1230}
1979/06/04

Improved Engine Design Uses Cylinder Block With Spacer Plate And New Crankshaft Thrust Plates{1000}
1979/07/02

Checking Crankshaft Journal Surface Hardness On Remanufactured Crankshafts{1202}
1991/01/07

New Front Crankshaft Seal Used{1160,1202}
1991/02/18

Use the 171-7212 Wear Sleeve to Repair the Crankshaft Hub {1160}
2011/09/20

A New Type of Main Bearing is Available {1203}
2005/12/26

40 Power Microscope is Available for Inspecting Bearing Journals on Crankshafts {0777, 1202}
2006/01/16

Caterpillar Parts SIS Catalog D4D :

CRANKSHAFT BEARING REPLACEMENT GROUP

7S-5110 CRANKSHAFT GROUP

2P-8774 CYLINDER BLOCK AS

5S-6407 CYLINDER BLOCK ASSEMBLY

7S-1236 CYLINDER BLOCK AND COVERS

CRANKSHAFT BEARING REPLACEMENT GROUP

GASKET KITS

CRANKSHAFT BEARING REPLACEMENTS

5S-6425 BALANCER GP

FLYWHEEL

5S-6429 CONNECTING ROD AND PISTON

5S-6428 CAMSHAFT

Truck sale:

14,000

Caterpillar D4D, Construction
- Dozers
MICHIGAN CAT

CATERPILLAR D4D 1966
- TRACK TYPE TRACTORS
MICHIGAN CAT
US (Mid, North), Canada, ON West: John Kinney; US (NE, SE, SW), Canada QU East, AUS: Bill Dowd;

CATERPILLAR D4D 1973
- TRACK TYPE TRACTORS
MICHIGAN CAT
US (Mid, North), Canada, ON West: John Kinney; US (NE, SE, SW), Canada QU East, AUS: Bill Dowd;

USD $39,016

CAT D4D

Hydraulics & Tractors Service Pty Ltd
Dubbo, NSW, Australia

USD $18,900

CAT D4D

DRC Ranch