AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

3N3387 FUEL INJECTION PUMP GROUP Serial No. 4B5547-Up Part of Fuel Pump Housing and Governor shown on Page 24B 3304


FUEL SYSTEM
PUMP GP-FUEL INJECTION
LINES GP-FUEL
LUBRICATION SYSTEM
PUMP GP-ENGINE OIL
COOLING SYSTEM
COOLER GP

INDUSTRIAL ENGINE 3304 INDUSTRIAL ENGINE 04B
 D330C ENGINE 04B00001-06031 UEG0014S 3304 04B   (1968)

FUEL SYSTEM

PUMP GP-FUEL INJECTION
FUEL INJECTION PUMP GROUP
3N-3387 FUEL INJECTION PUMP GROUP
 

#UEG0014S0080
 

3N-3387: FUEL INJECTION PUMP GROUP

3N3387 FUEL INJECTION PUMP GROUP
Serial No. 4B5547-Up
Part of Fuel Pump Housing and Governor shown on Page 24B
c141766 UEG0014S
3N3387 FUEL INJECTION PUMP GROUP Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
  4M-0411 [4] BONNET  
  8H-9204 [4] WASHER  
  2M-4314 [4] BUSHING  
  9B-1363 [4] SPRING  
  9H-5746 [4] CHECK  
  1M-3506 [4] RING  
  9H-5797 [4] PLUNGER AND BARREL ASSEM.  
  1S-0206 [4] SPRING  
  9H-5729 [4] WASHER  
  3S-9735 [4] LIFTER ASSEM.  
  4M-1474 [2] PIN  
  4F-6024 [2] DOWEL  
  1S-1953 [1] BEARING  
    (Parts of 3N3386 Assem.)
  8H-9208 [1] DOWEL  
    (Part of 5S5058 Assem.)
  1S-0214 [1] SPRING  
  2S-7905 [1] PLUG  
    (Part of 3N3386 Assem.)
  0L-0472 [1] BOLT  
  2H-3504 [1] LOCK  
  8H-9208 [1] DOWEL  
    (Part of 8H9207 Assem.)
  7M-5940 [1] PLATE  
  5S-5058 [1] GEAR ASSEM.  
    (66 Teeth)
  2A-3746 [1] PLUG  
  2M-8604 [1] BEARING  
  2S-7905 [1] PLUG  
    (Parts of 3N3386 Assem.)
  1M-1077 [4] SEAL  
  1P-0233 [4] DOWEL  
  1P-0231 [4] BALL  
  1P-0234 [4] DOWEL  
  1P-0232 [4] BALL  
    (Parts of 3N3886 Assem.)
  2M-4208 [4] SPACER (.174 in. thick)  
  2M-4209 [4] SPACER (.178 in. thick)  
  2M-4210 [4] SPACER (.182 in. thick)  
  2M-4211 [4] SPACER (.186 in. thick)  
  2M-4212 [4] SPACER (.190 in. thick)  
  5M-2691 [4] SPACER (.194 in. thick)  
  5M-2697 [4] SPACER (.170 in. thick)  
  5S-7189 [4] SPACER (.198 in. thick)  
    (Use as Required)
  9S-4160 [1] BEARING  
    (Part of 3N3386 Assem.)
  3N-3385 [1] RACK  
  9H-1284 [1] BEARING  
    (Part of 3N3386 Assem.)
  1M-0690 [1] SLEEVE  
    (Part of 8H9207 Assem.)
  8H-9207 [1] CAMSHAFT ASSEM.  
  3N-3386 [1] HOUSING ASSEM.  
 

#UEG0014S0081
 

7L-0342: FUEL INJECTION VALVES AND LINES

FUEL INJECTION VALVES AND LINES (7L342 N/S)
Serial No. 4B1 to 4B801 inclusive
c103023 UEG0014S
7L0342 FUEL INJECTION VALVES AND LINES Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1N-5404 [1] LINE ASSEM. (No. 4)  
2. 1N-5403 [1] LINE ASSEM. (No. 3)  
3. 1N-5402 [1] LINE ASSEM. (No. 2)  
4. 1N-5401 [1] LINE ASSEM. (No. 1)  
5. 7S-9891 [4] VALVE SERVICE GROUP  
6. 6F-1069 [4] SEAL ASSEM.  
7. 5B-3718 [4] SEAL  
    (1 each in 7L9891 Valve Service Group)
8. 5H-7225 [4] NUT  
9. 7M-4603 [4] BODY  
10. 4S-8385 H TUBING (.250" O.D.) 25.73" Long  
11. 1L-9456 [1] FITTING  
  4H-2495 [2] NUT  
  4H-2494 [2] SLEEVE  
    (Parts of 1L9456 Fitting)
12. 4S-8385 H TUBING (.250" O.D.) 17.67" Long  
13. 2B-2404 [1] CLIP  
14. 0S-0509 [1] BOLT  
15. 3B-4506 [4] LOCKWASHER  
16. 1A-2029 [1] BOLT  
17. 0S-1588 [1] BOLT  
18. 2H-3932 [2] SEAL  
19. 7L-0346 [1] BRACKET  
20. 7F-8607 [1] SEAL  
21. 3J-5389 [1] PLUG  
22. 0S-1591 [1] BOLT  
23. [1] BOLT  
24. 4L-3754 [1] LOCK  
25. 8F-3469 [1] SEAL  
26. 3B-6552 [1] ELBOW  
27. 4S-6574 [1] GAUGE (Fuel Pressure)  
28. 0S-1615 [3] BOLT  
29. 1B-4330 [3] NUT  
30. 3B-4504 [3] LOCKWASHER  
31. 6F-8868 [6] CLAMP  
  H   ORDER BY THE FOOT
 

#UEG0014S0082
 

7L-0342: FUEL INJECTION VALVES AND LINES

FUEL INJECTION VALVES AND LINES (7L342 N/S)
Serial No. 4B802 to 4B5124 and 4B5174 to 4B5191 inclusive
c126575 UEG0014S
7L0342 FUEL INJECTION VALVES AND LINES Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1N-5404 [1] LINE ASSEM. (No. 4)  
2. 1N-5403 [1] LINE ASSEM. (No. 3)  
3. 1N-5402 [1] LINE ASSEM. (No. 2)  
4. 1N-5401 [1] LINE ASSEM. (No. 1)  
5. 7S-9891 [4] VALVE SERVICE GROUP  
6. 6F-1069 [4] SEAL ASSEM.  
7. 5B-3718 [4] SEAL  
    (1 each in 7L9891 Valve Service Group)
8. 5H-7225 [4] NUT  
9. 7M-4603 [4] BODY  
10. 6F-8868 [6] CLAMP  
11. 4H-1966 C [1] FITTING  
  4H-2495 [1] NUT  
  4H-2494 [1] SLEEVE  
    (Parts of 4H1966 Fitting)
12. 4S-8385 H TUBING (.250" O.D.) 17.67" Long  
13. 2B-2404 [1] CLIP  
14. 0S-0509 [1] BOLT  
15. 3B-4506 [4] LOCKWASHER  
16. 1A-2029 [1] BOLT  
17. 0S-1588 [1] BOLT  
18. 8M-5248 C [2] SEAL  
19. 7L-0346 [1] BRACKET  
20. 8M-5253 C [1] SEAL  
21. 3J-5389 [1] PLUG  
22. 0S-1591 [1] BOLT  
23. [1] BOLT  
24. 4L-3754 [1] LOCK  
25. 8M-5260 C [1] SEAL  
26. 3B-7896 C [1] ELBOW  
27. 4S-6574 [1] GAUGE (Fuel Pressure)  
28. 0S-1615 [3] BOLT  
29. 1B-4330 [3] NUT  
30. 3B-4504 [3] LOCKWASHER  
  C   INDICATES CHANGE FROM PREVIOUS
  H   ORDER BY THE FOOT
 

#UEG0014S0083
 

7L-0342: FUEL INJECTION VALVES AND LINES

FUEL INJECTION VALVES AND LINES (7L342 N/S)
Serial No. 4B5125 to 4B5173 and 4B5192-Up
c140885 UEG0014S
7L0342 FUEL INJECTION VALVES AND LINES Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1N-5404 [1] LINE ASSEM. (No. 4)  
2. 1N-5403 [1] LINE ASSEM. (No. 3)  
3. 1N-5402 [1] LINE ASSEM. (No. 2)  
4. 1N-5401 [1] LINE ASSEM. (No. 1)  
5. 7S-9891 [4] VALVE SERVICE GROUP  
6. 6F-1069 [4] SEAL ASSEM.  
7. 5B-3718 [4] SEAL  
    (1 each in 7L9891 Valve Service Group)
8. 5H-7225 [4] NUT  
9. 7M-4603 [4] BODY  
10. 6F-8868 [6] CLAMP  
11. 4H-1966 [1] FITTING  
  4H-2495 [1] NUT  
  4H-2494 [1] SLEEVE  
12. 4S-8385 H TUBING (.250" O.D.) 17.67" Long  
13. 2B-2404 [1] CLIP  
14. 0S-0509 [1] BOLT  
15. 3B-4506 [4] LOCKWASHER  
16. 1A-2029 [1] BOLT  
17. 0S-1588 [1] BOLT  
18. 8M-5248 [2] SEAL  
19. 3N-3694 C [1] BRACKET  
20. 8M-5253 [1] SEAL  
21. 3J-5389 [1] PLUG  
22. 0S-1591 [1] BOLT  
23. 1D-4569 C [1] BOLT  
24. 4L-3754 [1] LOCK  
25. 8M-5260 [1] SEAL  
26. 3B-7896 [1] ELBOW  
27. 4S-6574 [1] GAUGE (Fuel Pressure)  
28. 0S-1615 [3] BOLT  
29. 1B-4330 [3] NUT  
30. 3B-4504 [3] LOCKWASHER  
  C   INDICATES CHANGE
  H   ORDER BY THE FOOT
 

#UEG0014S0084
 

7S-9463: OIL PUMP GROUP

7S9463 OIL PUMP GROUP
c115778 UEG0014S
7S9463 OIL PUMP GROUP Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 1A-2029 [2] BOLT  
  7H-1861 [2] LOCK  
2. 6H-4208 [1] LOCK  
3. 0S-1590 [4] BOLT  
4. 2P-2221 [1] ELBOW ASSEM.  
5. 4B-3938 [2] PLUG  
6. 0S-1594 [2] BOLT  
7. 8S-9300 [1] BELL ASSEM.  
8. 8M-0904 [1] GASKET  
9. 7S-9461 Y [1] PUMP GROUP  
    (Separate Illustration)
10. 8S-8874 [1] LOCK  
11. 0T-0329 [1] LOCK  
12. 7H-1796 [1] GASKET  
  Y   SEPARATE ILLUSTRATION
 

#UEG0014S0085
 

7S-9461: OIL PUMP ASSEMBLY

7S9461 OIL PUMP ASSEMBLY
Serial No. 4B1 to 4B1463 inclusive
Part of 7S9463 Oil Pump Group
c221371 UEG0014S
7S9461 OIL PUMP ASSEMBLY Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
  8S-0488 [1] BODY ASSEM.  
  8S-6511 [2] BEARING  
    (PART OF 8S488 BODY ASSEM.)
  0L-1352 [2] BOLT (3.25" LONG)  
  0L-0364 [2] LOCK  
  0S-1619 [1] BOLT (3"LONG)  
  5B-9603 [1] BOLT (5"LONG)  
  8S-8871 [1] LOCK  
  2H-3755 [2] BOLT  
  2A-5328 [2] LOCK  
  2S-9529 [1] PLUNGER  
  1S-3921 [1] SPRING  
  8S-0496 [1] COVER  
  8S-0485 [1] BODY ASSEM.  
  8S-0491 [2] GEAR (8 TEETH)  
  8M-5599 [1] KEY  
  8S-0486 [1] SPACER  
  4B-9880 [1] BALL  
  1F-1006 [1] DOWEL  
  8S-6511 [2] BEARING  
    (PARTS OF 8S485 ASSEM.)
  9S-1160 [1] BEARING  
    (PART OF 9S1179 GEAR ASSEM.)
  7S-6309 [1] SHAFT ASSEM.  
    (PART OF 8S485 BODY ASSEM.)
  6F-7172 [1] DOWEL  
    (PART OF 7S6309 SHAFT ASSEM.)
  9S-1179 C [1] GEAR ASSEM.  
    (60 TEETH-IDLER)
  8S-0494 [1] SHAFT ASSEM.  
    (8 TEETH)
  3B-6734 [1] NUT  
  6B-0863 [1] WASHER  
  3B-4617 [1] COTTER PIN  
  8S-0497 [1] GEAR  
    (40 TEETH-DRIVE)
  8S-0493 [1] SHAFT ASSEM.  
    (8 TEETH)
  1M-3735 [2] DOWEL  
    (PART OF 8S488 BODY ASSEM.)
  C   INDICATES CHANGE
 

#UEG0014S0086
 

7S-9461: GEAR PUMP GROUP

7S9461 GEAR PUMP GROUP--Double Section
Serial No. 4B1464-Up
Part of 7S9463 Oil Pump Group shown on Page 30
c221372 UEG0014S
7S9461 GEAR PUMP GROUP Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 5B-9603 [1] BOLT--12.70cm(5 in.) long  
2. 0S-1619 [1] BOLT--(7.62cm(3 in.) long  
3. 0L-0364 [2] LOCK  
4. 0L-1352 [2] BOLT--8.25cm(3.25 in.) long  
5. 8S-8871 [1] LOCK  
6. 8S-0486 C [1] SPACER  
7. 1B-8709 C [1] KEY  
8. 9S-3040 [1] SHAFT ASSEM.--(8 Teeth)  
9. 8M-5599 C [1] KEY  
10. 8S-0485 [1] BODY ASSEM.  
11. 1F-1006 [1] DOWEL  
12. 4B-9880 [1] BALL  
13. 8S-6511 [2] BEARING  
14. 7S-6309 [1] SHAFT ASSEM.  
15. 6F-7172 [1] DOWEL  
16. 8S-0497 [1] GEAR--(40 Teeth-Drive)  
17. 6B-0863 [1] WASHER  
18. 3B-6734 [1] NUT  
19. 3B-4617 [1] COTTER PIN  
20. 9S-1179 C [1] GEAR ASSEM.--(60 teeth)  
21. 9S-1160 [1] BEARING  
22. 8S-0493 [1] SHAFT ASSEM.--(8 Teeth)  
23. 8S-0491 [2] GEAR--(8 Teeth)  
24. 8S-0488 [1] BODY ASSEM.  
25. 8S-6511 [2] BEARING  
26. 1M-3735 [2] DOWEL  
27. 2S-9529 [1] PLUNGER  
28. 1S-3921 [1] SPRING  
29. 8S-0496 [1] COVER  
30. 2H-3755 [2] BOLT  
31. 2A-5328 [2] LOCK  
  C   INDICATES CHANGE
 

#UEG0014S0087
 

OIL COOLER AND FILTER

OIL COOLER AND FILTER
Serial No. 4B557 to 4B917 inclusive
7L6925 Filter parts are shown on Page 30D
c125112 UEG0014S
None OIL COOLER AND FILTER Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9B-0887 [1] PLUG  
2. 8L-4202 [1] TUBE (Vent)  
3. 3B-8998 [2] FITTING  
  1F-1344 [2] NUT  
    (1 in each 3B8998 Fitting)
4. 7L-0318 [1] BONNET  
5. 0S-1588 [4] BOLT (1.25" Long)  
6. 3B-4506 [25] LOCKWASHER  
7. 4B-4278 [2] WASHER  
8. 6L-5362 [2] GASKET  
9. 1A-2029 [11] BOLT (1.125" Long)  
10. 5M-4741 [1] GASKET  
11. 5F-4899 [1] BOLT  
12. 7L-7749 [1] COOLER ASSEM.  
13. 7L-0312 [1] GASKET  
14. 3J-5390 [1] PLUG  
15. 1N-8176 [1] BONNET  
16. 3D-2971 [2] PLUG  
  6B-7020 [2] GASKET  
  8M-3182 [2] SPRING  
  9M-0853 [2] PLUNGER  
17. 0S-1608 [1] BOLT  
18. 5L-6573 [2] LUG  
19. 0S-0509 [2] BOLT  
20. 1M-9390 [1] GASKET  
21. 9M-4849 [2] SEAL  
22. 0S-1591 [2] BOLT  
23. 7L-0315 [1] TUBE ASSEM. (Oil Cooler Inlet)  
24. 7L-0304 [1] TUBE ASSEM. (Oil Cooler Outlet)  
25. 2L-9653 [1] CLIP  
26. 7L-6925 Y [1] FILTER ASSEM.  
    (See Separate Illustration)
27. 6L-5305 [1] GASKET  
28. 7F-7590 [1] GASKET  
29. 0L-2070 [1] BOLT (2.25" Long)  
30. 0S-1619 [1] BOLT (4" Long)  
31. 2J-6540 [2] CLAMP  
32. 9L-1794 [1] HOSE  
33. 8L-8509 [1] ELBOW  
34. 2A-4638 [1] GASKET  
35. 0S-1594 [2] BOLT  
  Y   SEPARATE ILLUSTRATION
 

#UEG0014S0088
 

1N-5320: OIL COOLER AND FILTER

OIL COOLER AND FILTER (1N5320 N/S)
Serial No. 4B918 to 4B3101 inclusive
7L6925 Filter parts are shown on Page 30D
c126250 UEG0014S
1N5320 OIL COOLER AND FILTER Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9B-0887 [1] PLUG  
2. 8L-4202 [1] TUBE (Vent)  
3. 3B-8998 [2] FITTING  
  1F-1344 [2] NUT  
    (1 in each 3B8998 Fitting)
4. 7L-0318 [1] BONNET  
5. 0S-1588 [4] BOLT (1.25" Long)  
6. 3B-4506 [25] LOCKWASHER  
7. 4B-4278 [2] WASHER  
8. 8M-5254 C [2] SEAL  
9. 1A-2029 [11] BOLT (1.125" Long)  
10. 5M-4741 [1] GASKET  
11. 5F-4899 [1] BOLT  
12. 7L-7749 [1] COOLER ASSEM.  
13. 7L-0312 [1] GASKET  
14. 3J-5390 [1] PLUG  
15. 1N-8176 [1] BONNET  
16. 3D-2971 [2] PLUG  
  6B-7020 [2] GASKET  
  8M-3182 [2] SPRING  
  9M-0853 [2] PLUNGER  
17. 0S-1608 [1] BOLT  
18. 5L-6573 [2] LUG  
19. 0S-0509 [2] BOLT  
20. 1M-9390 [1] GASKET  
21. 9M-4849 [2] SEAL  
22. 0S-1591 [2] BOLT  
23. 7L-0315 [1] TUBE ASSEM. (Oil Cooler Inlet)  
24. 7L-0304 [1] TUBE ASSEM. (Oil Cooler Outlet)  
25. 2L-9653 [1] CLIP  
26. 7L-6925 Y [1] FILTER ASSEM.  
    (See Separate Illustration)
27. 6L-5305 [1] GASKET  
28. 7F-7590 [1] GASKET  
29. 0L-2070 [1] BOLT (2.25" Long)  
30. 0S-1619 [1] BOLT (4" Long)  
31. 2J-6540 [2] CLAMP  
32. 9L-1794 [1] HOSE  
33. 8L-8509 [1] ELBOW  
34. 2A-4638 [1] GASKET  
35. 0S-1594 [2] BOLT  
  C   INDICATES CHANGE FROM PREVIOUS
  Y   SEPARATE ILLUSTRATION
 

#UEG0014S0089
 

1N-5320: OIL COOLER AND FILTER

OIL COOLER AND FILTER (1N5320 N/S)
Effective with Serial No. 4B3102
7L6925 Filter parts are shown on Page 30D
c131649 UEG0014S
1N5320 OIL COOLER AND FILTER Parts scheme
  For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9B-0887 [1] PLUG  
2. 8L-4202 [1] TUBE (Vent)  
3. 3B-8998 [2] FITTING  
  1F-1344 [2] NUT  
    (1 in each 3B8998 Fitting)
4. 7L-0318 [1] BONNET  
5. 0S-1588 [4] BOLT (1.25" long)  
6. 3B-4506 [24] LOCKWASHER  
7. 4B-4278 [2] WASHER  
8. 8M-5254 [2] SEAL  
9. 1A-2029 [10] BOLT (1.25" long)  
10. 5M-4741 [1] GASKET  
11. 5F-4899 [1] BOLT  
12. 7L-7749 [1] COOLER ASSEM.  
13. 7L-0312 [1] GASKET  
14. 3J-5390 [1] PLUG  
15. 1N-8176 [1] BONNET  
16. 3D-2971 [2] PLUG  
  6B-7020 [2] GASKET  
  8M-3182 [2] SPRING  
  1P-1367 [2] PLUNGER  
17. 0S-1608 [1] BOLT  
18. 4S-1994 [1] LUG  
19. 3B-1915 [2] BOLT  
20. 1M-9390 [1] GASKET  
21. 2N-3350 [2] SEAL  
22. 0S-1591 [2] BOLT  
23. 2N-5720 [1] TUBE ASSEM. (Oil Cooler Inlet)  
24. 7L-0304 [1] TUBE ASSEM. (Oil Cooler Outlet)  
25. 2L-9653 [1] CLIP  
26. 7L-6925 Y [1] FILTER ASSEM.  
    (See Separate Illustration)
27. 6L-5305 [1] GASKET  
28. 7F-7590 [1] GASKET  
29. 0L-2070 [1] BOLT (2.25" long)  
    - or -
  5B-0213 [1] BOLT (2.375" long)  
30. 0S-1619 [1] BOLT (4" long)  
31. 2J-6540 [2] CLAMP  
32. 9L-1794 [1] HOSE  
33. 8L-8509 [1] ELBOW  
34. 2A-4638 [1] GASKET  
35. 0S-1594 [2] BOLT  
36. 2S-6160 [2] WASHER  
  Y   SEPARATE ILLUSTRATION
 

Information:

Engine News
A New 6V29 Sleeve Metering Fuel System Pump Roll Pin Tool Is Used To Adjust And Make A Replacement Of Roll Pins In The Fuel Injection Pump Housing
1979/01/24
Part Numbers Of Bearings To Use For Service Replacement In Fuel Injection Pump Housings For Sleeve Metering Fuel Systems; Correction To Special Instruction For Installation.
1979/05/09
New Seal Used Under Retaining Bushing For Fuel Injection Pump Bonnet
1979/08/22
Improvements Made To Fuel Injection Pump And Governor Group
1979/11/28
New Fuel Injection Nozzle Assembly Used
1980/01/23
Use 6V4089 Reamer Assembly To Clean Nozzle Bores
1981/05/20
Explanation Of Differences In Timing Advance Information
1981/08/26
Timing Pin Removed From Governor And Fuel Injection Pump Group; Change To Service Manuals
1981/09/16
New Fuel Nozzle Test Sheet Available
1982/10/20
Bulged Capsule-Type Fuel Nozzles
1982/10/20
Do Not Use A Wire Brush On Fuel Nozzles
1982/10/20
6V6175 And 6V6176 Torque Adapters Make Installation Of Fuel Pump Drive Gear Easier
1982/11/10
New Seal Used On Governor Control Shaft
1982/12/15
Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/15
Service Information For Woodward Governors
1983/10/26
Fill Oil Sump Before Installing Woodward Governor
1985/01/16
Check Fuel Injection Nozzles In Overheated Engines
1985/09/01
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings
1985/12/01
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle
1986/04/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
Use Correct Compression Seal Washer (Gas Seal) On 7000 Series Fuel Injection Nozzles
1986/10/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
New Bleed Screw Used On 7000 Series Fuel Injection Nozzles
1989/03/01
New Shaft Bracket And Oil Supply Plug Used In Rocker Valve Shaft Assembly
1991/04/01
New Gaskets Help Prevent Leaks From Fuel System Governors{1264}
1991/12/01
Identification Of Remanufactured Direct Injection Fuel Nozzles (DIFN)
1992/04/01
Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/01
Pressure Compensated Simple Governor (PSG Governor) Changes From Aluminum To Cast Iron Housing {1264}
1995/04/01
Manufacturing And Design Improvements Incorporated Into Fuel Injection Nozzle Assemblies{1252,1307}
1997/07/01
Troubleshooting Reminder For Engine Low Power Or Intermittent Low Power Symptoms{1250,1252,1256,1260,1261,1273}
1998/10/01
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
A New Exhaust Manifold And Fuel Pump Heat Shield Is Used On Industrial Engines That Have A Woodward Governor With An Electric Motor
1978/07/05
Improved Guide Pin For Fuel Injection Pump Lifters
1978/08/30
Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01
Special Instruction
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Use Of 6V-4180 Timing Fixture Group To Check Off-Engine Timing Dimension Setting{1251, 0653}
Use Of 6V-4180 Timing Fixture Group To Check Off-Engine Timing Dimension Setting{1251, 0653}
Replacement For The 2M4314 Fuel Pump Bonnet Retaining Bushing{1250}
Replacement For The 2M4314 Fuel Pump Bonnet Retaining Bushing{1250}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Installation Of 5P4810 Bearing In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of 5P4810 Bearing In Sleeve Metering Fuel Injection Pump Housing{1253}
Governor Linkage Adjustments{1264, 1289}
Governor Linkage Adjustments{1264, 1289}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N628 Bearing{7551, 1253}
Installation Of 8N628 Bearing{7551, 1253}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Repair Of Precombustion Chamber And Direct Injection Adapter Seating Surfaces{1101}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Determining the Cause of Fuel Dilution of Engine Oil {1101, 1124, 1251, 1280, 1290}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Technical Information Bulletin
3300 Engine Timing Measurement For Reduced Emissions And Improved Engine Performance/Life
3300 Engine Timing Measurement For Reduced Emissions And Improved Engine Performance/Life
Specifications
Fuel Injection Equipment
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump<BR> (4N4864)
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump<BR> (7L543 and 2N8603)
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Governor
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Fuel Bypass Valve
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Woodward PSG Governors
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Output Shaft Governor<BR> (8L8661)
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Equipment
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Adjustable &quot;Dashpot&quot;<BR> (Close Regulation Type Governor)
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel System Timing<BR> (Engines With Timing Pointer)
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Automatic Timing Advance Unit
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Woodward PSG Governor
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Woodward PSG Governor<BR> (8N6774)
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Governor Control
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Information Release Memo
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
APPEARANCE CHANGE ON REMAN SHORT BLOCKS
Disassembly and Assembly
Fuel Transfer Pump
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing And Governor
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Governor
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Valves
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Rocker Shaft Assembly And Push Rods (D330C, D333C, 3304 &amp; 3306 Industrial Engines)
D330, D333, 3304, 3306 INDUSTRIAL & MARINE ENGINES
Adapter Housing And Levers
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing And Governor
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Check Valve And Bypass Valve
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Governor
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pumps
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pump Housing
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Fuel Injection Valves
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Rocker Shaft And Push Rods
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Rocker Shaft (Later)
3304 & 3306 INDUSTRIAL & MARINE ENGINES
Service Magazine
New Fuel Injection Nozzle Assembly Used{1254}
1980/01/21
New Fuel Injection Lines And Clamps Prevent Stresses And Contact Which Can Cause Leakage{1252}
1980/03/24
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1981/02/23
Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17
FT1632 Bolt Used During Removal Of Sleeve From Sleeve Metering Fuel System{0621,1251,1253}
1981/08/31
Timing Pin Removed From Governor And Fuel Injection Pump Group; Change To Service Manuals {1286}
1981/09/14
New Torque Specification For Bushing{0374,1253,1251}
1982/01/18
New 6V4818 Driver Available To Install Rack Bearings In Fuel Injection Pump Housings{0622}
1982/02/08
New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach{0651}
1982/05/03
Modification Of 2P8315 Bracket Assembly{0652,1286}
1982/08/16
Do Not Use A Wire Brush On Fuel Nozzles{1254}
1982/09/27
New Tool Makes Installation Of Carbon Stop Seals Easier{0622,1254}
1982/10/04
New Fuel Nozzle Test Sheet Available{0651,1254}
1982/10/04
Bulged Capsule-Type Fuel Nozzles{1254}
1982/10/11
6V6175 And 6V6176 Torque Adapters Make Installation Of Fuel Pump Drive Gear Easier{1206,1272,0614}
1982/11/08
New Seal Used On Governor Control Shaft{1264,1265}
1982/11/22
Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22
Service Information For Woodward Governors{0374,1264}
1983/09/26
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1983/12/05
New Speed Setting Motor Assembly On Woodward PSG Governor Has More Resistance To Moisture And Vibration Damage{1264}
1984/05/14
Fill Oil Sump Before Installing Woodward Governor{1264,1288,1289}
1984/12/10
Valve Lash Adjustment Not A Warranty Item {1102,1105}
1985/01/14
Only The External Needle Valve Can Be Adjusted On Woodward EG3PC Or EG10PC Actuators{1265,1289}
1985/02/04
Higher Torque Can Be Used With 6V6980 Nozzle Puller Group{0706,1254}
1985/06/10
Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02
New Bleed Screw Used In Fuel Injection Nozzle{1254}
1985/09/23
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings{1251}
1985/11/11
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Bleed Screw Washer (Seal) Must Be Replaced If Bleed Screw Removed From Fuel Nozzle{1254}
1986/04/07
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Use Correct Compression Seal Washer (Gas Seal) On 7000 Series Fuel Injection Nozzles{1254,1250}
1986/09/29
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
New Tie Bars Improve Stability Of The Fuel Injection Test Bench{0652}
1977/01/17
Test Used Fuel Nozzles Before You Install New Nozzles; Tips On Test Procedures{1254,0651,0336}
1977/02/14
With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31
Larger Diameter Holes Are Now Used In The Rocker Arm Shaft To Give More Oil Flow To Rocker Arm Bearings{1102}
1977/11/21
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
Improved Guide Pin For Fuel Injection Pump Lifters{1251}
1978/08/21
New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}
1978/09/25
Caterpillar Fuel Injection Test Bench Book{0374}
1978/10/16
New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04
Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18
New Tachometer Drive Adapter Has Increased Service Life{7462,1288}
1979/01/22
Check Valve Must Be Adjusted Correctly To Let Fuel Flow Through The Return Line And Back To The Tank{1275,1253,1274}
1979/03/12
Replacement Bushing Available For Cast Iron Rocker Arms Only{1102}
1979/03/26
Careful, Correct Installation And Maintenance Of Fuel Injection Lines Is Very Important To Prevent Possible Engine Damage, Fire And Other Problems{1252}
1979/04/23
Part Numbers Of Bearings To Use For Service Replacement In Fuel Injection Pump Housings For Sleeve Metering Fuel Systems; Correction To Special Instruction For Installation.{1253}
1979/05/07
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
New Seal Used Under Retaining Bushing For Fuel Injection Pump Bonnet{1251,1253,1286}
1979/08/13
New Rocker Arms And Rocker Arm Shaft Have Improved Lubrication{1102}
1979/08/27
General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17
New Bleed Screw Used On 7000 Series Fuel Injection Nozzles{1254}
1989/03/06
New Shaft Bracket And Oil Supply Plug Used In Rocker Valve Shaft Assembly{1102,7553}
1991/03/25
New Shaft Bracket And Oil Supply Plug Used In Rocker Valve Shaft Assembly{1102,7553}
1991/04/15
New Gaskets Help Prevent Leaks From Fuel System Governors{1264}
1991/12/02
Identification Of Remanufactured Direct Injection Fuel Nozzles (DIFN){1254}
1992/04/20
New Fuel Pump Drive Idler Gear Assembly And Shaft Used In Front Timing Gear Groups {1206}
1993/06/14
Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/23
New Fuel Nozzles Resist Adapter Cracking And Leaking {1254}
1999/06/14
Do Not Reuse the Hold Down Bolts for the Fuel Injectors On All Products that Contain C9 Through C32 Engines {1290}
2014/08/14

Caterpillar Parts SIS Catalog 3304 :

FUEL PUMP HOUSING GROUP
7S-8831 FUEL PUMP HOUSING GROUP
FUEL PUMP HOUSING GROUP
7S-8831 FUEL PUMP HOUSING GROUP
FILTER & PRM GP
7L-0261 FILTER & PRM GP
FILTER & PRM GP
7L-0261 FILTER & PRM GP
FILTER & PRM GP
7L-0261 FILTER & PRM GP
FILTER & PRM GP
7L-0261 FILTER & PRM GP
FUEL TRANSFER PUMP GROUP
7L-0543 FUEL TRANSFER PUMP GROUP
SERVICE METER GROUP
2S-0423 SERVICE METER GROUP
FUEL INJECTION VALVES AND LINES
7L-0342 FUEL INJECTION VALVES AND LINES
FUEL INJECTION VALVES AND LINES
7L-0342 FUEL INJECTION VALVES AND LINES
FUEL INJECTION VALVES AND LINES
7L-0342 FUEL INJECTION VALVES AND LINES
OIL PUMP GROUP
7S-9463 OIL PUMP GROUP
OIL PUMP ASSEMBLY
7S-9461 OIL PUMP ASSEMBLY
GEAR PUMP GROUP
7S-9461 GEAR PUMP GROUP
OIL COOLER AND FILTER
OIL COOLER AND FILTER
OIL COOLER AND FILTER
1N-5320 OIL COOLER AND FILTER

Truck sale:

Caterpillar 303/304 20 HD BUCKET, bucket, Construction
854 
Caterpillar 303/304 20 HD BUCKET, bucket, Construction
- bucket
MILTON CAT
 
30,000 
Caterpillar 3304B, Stationary Generator Sets, Construction


Caterpillar 3304B, Stationary Generator Sets, Construction
30,000 
Caterpillar 3304B, Stationary Generator Sets, Construction

FOLEY EQUIPMENT COMPANY
Caterpillar 303/304 ADAPTER SSL TO MHE, Schnellwechsler, Bau-Und Bergbauausrüstung
650 
Caterpillar 303/304 ADAPTER SSL TO MHE, Schnellwechsler, Bau-Und Bergbauausrüstung
- Quick connectors
MILTON CAT
Caterpillar 3304, Stationäre Stromaggregate, Bau-Und Bergbauausrüstung
17.000 
Caterpillar 3304, Stationäre Stromaggregate, Bau-Und Bergbauausrüstung
- Stationary Generator Sets
EMPIRE MACHINERY
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.