9S7977 TOOL GROUP AN ATTACHMENT 3304 INDUSTRIAL ENGINE

SERVICE EQUIPMENT AND SUPPLIES

TOOLS

0. 9S-7977 TOOL GP-HA

CHARTS & FILMS

1. NAME PLATE
0. INFORMATION

INDUSTRIAL ENGINE 3304 INDUSTRIAL ENGINE 04B
D330C ENGINE 04B00001-06031 UEG0014S 3304 04B (1968)

SERVICE EQUIPMENT AND SUPPLIES

TOOLS

4L-1560 TOOL GROUP

8F-9866 GREASE GUN AS

9S-7977 TOOL GP-HAND

#UEG0014S0410

9S-7977: TOOL GP-HAND

TOOL GP-HAND

9S7977 TOOL GROUP
AN ATTACHMENT

c201200 UEG0014S

For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name	Comments
	8F-9866 Y		GREASE GUN (Lever)
			(See Separate Illustration)
	9S-1738		SCREWDRIVER NO. 2 PHILLIPS
	1F-1157		SCREWDRIVER
	5S-9567		EXTENSION
	5S-9566		WRENCH
	2P-8250		STRAP WRENCH ASSEM.
	8H-8581		GAUGE (Feeler)
	5F-4764		PRY BAR
	5S-9568		SOCKET
	5S-9569		SOCKET
	5P-1763 C		SOCKET
	8H-8503		WRENCH (5/16" Opening)
	8H-8505		WRENCH (3/8" Opening)
	8H-8513		WRENCH (7/8" Opening)
	8H-8508		WRENCH (9/16" Opening)
	8H-8509		WRENCH (5/8" Opening)
	8H-8511		WRENCH (3/4" Opening)
	8H-8515		WRENCH (1" Opening)
	8H-8549		SOCKET (9/16" Opening)
	8H-8554		SOCKET ( 7/8" Opening)
	8H-8555		SOCKET (15/16" Opening)
	8H-8556		SOCKET ( 1" Opening)
	9S-1730		SOCKET (11/8" Opening)
	C		INDICATES CHANGE
	Y		SEPARATE ILLUSTRATION

#UEG0014S0411

NAME PLATES AND TRANSFERS

UEG0014S0411 UEG0014S

For full view, you need register

Parts for your 3304 INDUSTRIAL ENGINE:

CATERPILLAR SIS

Part No	Qty	Parts name
5L-3985	[1]	PLATE WARNING AND INFORMATION
		ON FLYWHEEL HOUSING
2M-6831	[1]	PLATE SERIAL NUMBER
		ON L.H. SIDE OF CYLINDER BLOCK
7B-3028	[10]	DRIVE SCREW
1H-3040	[1]	TRANSFER SAFETY
		ON DASH OR GUARDS WHEN USED
1M-4898	[1]	TRANSFER FILTER INSTRUCTIONS
		ON OIL FILTER COVER
7M-2214	[1]	TRANSFER AIR CLEANER INSTRUCTIONS
		ON SIDE OF DIESEL AIR CLEANER
1S-9547	[1]	TRANSFER CRANKCASE INSTRUCTIONS
		ON OIL FILTER OR OPEN SPACE NEAR OIL FILLER

Information:

SERVICE EQUIPMENT AND SUPPLIES

TOOLS

Truck Engine News

New Infrared Thermometer Has Narrow, 50:1 Target Ratio, Wide Temperature Range {0776, 1350, 3000, 4000, 4150, 4250}
2006/03/27

Engine News

New 6V87 Gauge Measures Valve Stem Wear
1979/01/10

A New 6V29 Sleeve Metering Fuel System Pump Roll Pin Tool Is Used To Adjust And Make A Replacement Of Roll Pins In The Fuel Injection Pump Housing
1979/01/24

New 6V2120 Spline Sprocket Improves Depth Control Of 5P4175 Boring Tool Group
1980/05/14

6V2050 Tapered Rod Tool Group Available For Removal And Installation Of Bearings
1980/07/09

Timing Groups To Be Canceled
1980/07/09

Modification Of Puller Bolt Prevents Thread Damage During Removal Of Sleeve From Sleeve Metering Fuel System
1980/11/12

6V3150 Engine Pressure Group And 6V3121 Multitach Group Are Available For Testing Engines
1981/01/28

Changes Have Been Made To Caterpillar Service Literature
1981/03/04

6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier
1981/04/01

Use 6V4089 Reamer Assembly To Clean Nozzle Bores
1981/05/20

Instruction Cards For "Go-No Go" Gauges Now Available
1981/07/01

6V3100 Diesel Timing Indicator Group Available To Check Engine/Fuel System Timing And Mechanical Advance During Operation
1981/08/26

FT1632 Bolt Used During Removal Of Sleeve From Sleeve Metering Fuel System
1981/09/16

New Engine Testing And Adjusting Tools Give More Accuracy And Longer Service Life
1982/02/24

Use 6V6035 Hardness Tester On Crankshafts
1982/02/24

Use The 6V6059 Microlite With The 6V2196 Inspection Microscope
1982/04/07

Correct Use Of 6V2023 Flow Check Adapter Group Is Important To Prevent Damage To An Engine
1982/04/07

New 6V4950 Injection Line Speed Pickup Group Used With 6V2100 Multitach
1982/05/12

New Address For Repair Of Diagnostic Tools
1982/06/16

Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25

Separate Valve Stem Gauges Available
1982/08/25

Dial Bore Gauge And Size Setting Fixture Available
1982/09/22

New Tool Makes Installation Of Carbon Stop Seals Easier
1982/09/22

Service Information For Easier Use Of The 6V3100 Timing Indicator Group
1982/10/20

Make Change To 6V2100 Multitach And 5P9698 Calibrator
1982/12/15

Use FT1711 Light Table For Cylinder Liner Inspection
1982/12/15

New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip
1982/12/15

Service Parts Available For The 5P4150 Nozzle Testing Group
1982/12/15

Use The 6V5000 Infrared Thermometer Group To Measure Temperatures
1983/04/27

New Service Centers For 6V3100 Engine Timing Indicator Group
1983/10/26

6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier
1984/01/18

Hunting Down The Cheaters
1985/06/01

Fuel Sulfur Analyzer Available
1986/01/01

Oil Total Base Number (TBN) Test Kit Available
1986/02/01

New Engine Timing Indicator Group Available
1986/07/01

Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01

New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity
1986/11/01

Check For Dirt Before Replacing Pyrometer Switch
1987/01/01

New 8T5261 Bushing Installer And Remover Adapter Tool Available
1987/03/01

Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups
1987/03/01

Check For Plugged Orifices In Mechanical Pressure Gauges
1987/03/01

5P957 And 5P3514 Coolant And Battery Tester
1987/04/01

Black Light Leak Detection Kit Available For Oil, Fuel and Cooling Systems
1987/05/01

Two New Self-Powered Digital Tachometers And Signal Generator Available
1987/05/01

Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group
1987/07/01

New Service Tools Available
1987/08/01

Fluid Sampling Tools For Nonpressurized Compartments
1988/03/01

Extraction Tools For "Live Oil Sampling"
1988/05/01

New Service Tools Available
1988/10/01

New 4C5084 Oil Filter Cutter Replaces Former 6V7905 Filter Cutter
1990/11/01

Checking Crankshaft Journal Surface Hardness On Remanufactured Crankshafts
1991/01/01

Cylinder Pack Puller Groups Improved
1993/01/01

New Socket Assembly To Tighten The Bolts That Fasten The Sleeve Levers To The Sleeve Shaft
1977/05/03

Use Correct Contact Point With Dial Indicator To Be Sure Of The Accuracy Of The Measurements Of Fuel Setting And Fuel Ratio Control Setting On Sleeve Metering Fuel Systems
1977/10/12

5P8665 Cylinder Liner Puller Makes Liner Removal Easier And Faster
1978/01/18

Replacement Seal Group For Water Pump Impeller Now Has All The Seal Parts Plus An Installation Tool
1978/03/01

Caterpillar Electronic Technician (Cat ET) 2001B-Service Pack 1 Software Upgrade is Now Available {0785}
2002/02/01

Do not Use the 6V-4022 Fuel Injector Tester to Test Unit Injectors {0782, 1251, 1254, 1290, 1713}
2008/12/01

Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {1000, 1052, 1087}

Special Instruction

Troubleshooting And Repair Of The 5P2160 Engine Horsepower Meter Arrangement*{0781, 0782}
Troubleshooting And Repair Of The 5P2160 Engine Horsepower Meter Arrangement^*{0781, 0782}

Using The 5P2160 Engine Horsepower Meter Arrangement*{0781, 0782}
Using The 5P2160 Engine Horsepower Meter Arrangement^*{0781, 0782}

Troubleshooting And Repair Of The 1P3500 And 2P8280 Injection Timing Groups{0782}
Troubleshooting And Repair Of The 1P3500 And 2P8280 Injection Timing Groups{0782}

Using The 5P-4150 Nozzle Testing Group{0782}
Using The 5P-4150 Nozzle Testing Group{0782}

Using The 4S6553 Engine Evaluation Test Group{0781}
Using The 4S6553 Engine Evaluation Test Group{0781}

Dynamometer Test Specifications For Caterpillar Engines{1000}
Dynamometer Test Specifications For Caterpillar Engines{1000}

Installation Of 6V124 Drive Coupling Modification Kit{0650, 0706, 1250}
Installation Of 6V124 Drive Coupling Modification Kit{0650, 0706, 1250}

Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}
Service Information And Use of 6V3100 Engine Timing Indicator Group{0782}

6V2150 Starting And Charging Analyzer Operating InstructionsFor More Information See Special Instruction SEHS7768{1406, 7569}
6V2150 Starting And Charging Analyzer Operating InstructionsFor More Information See Special Instruction SEHS7768{1406, 7569}

Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}

Using The 6V4950 Injection Line Speed Pickup Group{0782}
Using The 6V4950 Injection Line Speed Pickup Group{0782}

Electronic Repair Of 6V3100 Diesel Engine Timing Indicator{0651, 1250}
Electronic Repair Of 6V3100 Diesel Engine Timing Indicator{0651, 1250}

Use And Repair Of The 6V7925 Fuel Rate Indicator{0782}
Use And Repair Of The 6V7925 Fuel Rate Indicator{0782}

Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}
Use And Maintenance Of 8T0910 Fuel Sulfur Analyzer Group{0786, 1280}

Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}
Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}

Using The 8T1000 Position Indicator Group{0760, 0762}
Using The 8T1000 Position Indicator Group{0760, 0762}

Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}

Using the 1U6602 Photo-Tach Group{0775}
Using the 1U6602 Photo-Tach Group{0775}

Using the 1U5470 Engine Pressure Group{0781}
Using the 1U5470 Engine Pressure Group{0781}

Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}
Use of the 4C3502 Engine Repair Indicator Kit{0781, 1000}

Using the 4C6821 Injection Line Speed Pickup Group{0781}
Using the 4C6821 Injection Line Speed Pickup Group{0781}

Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}

Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}
Installing Crankshaft Seals And Wear Sleeves Using The Former 9S8868, 9S8873, 9S8881 And 9S8888 Tools Groups{1160, 1161, 0704}

Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}
Using The 5P6524 Engine Timing Indicator Group And 1P540 Flow Checking Tool Group{0782, 1000}

Operation And Maintenance Of 1P3060 Pyrometer Group{0776}
Operation And Maintenance Of 1P3060 Pyrometer Group{0776}

Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}

Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}
Use Of 6V22 Tool Group For Replacement Of Governor Spring Guide{620, 624, 1264}

Using The 5P2050 Connecting Rod Checking Fixture{0767, 1218}
Using The 5P2050 Connecting Rod Checking Fixture{0767, 1218}

Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}

Use Of 6V4141 Sleeve Metering Calibration Tool Group{0778, 0782}
Use Of 6V4141 Sleeve Metering Calibration Tool Group{0778, 0782}

Use Of 6V4805 Valve Seat Insert Puller Group{0703}
Use Of 6V4805 Valve Seat Insert Puller Group{0703}

Using The 6V7899 Size Setting Fixture Group{651}
Using The 6V7899 Size Setting Fixture Group{651}

Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}
Testing Flat-Seat Fuel Injection Valves Using The 5P4150 Nozzle Testing Group{0782, 1254}

Using 5P4175 Boring Tool Group And 5P1618 Tool Arrangement{0672, 1200}
Using 5P4175 Boring Tool Group And 5P1618 Tool Arrangement{0672, 1200}

Tool and Specification Chart for Inverted Duo-Cone Seals {0599, 7561}
Tool and Specification Chart for Inverted Duo-Cone Seals {0599, 7561}

Using Caterpillar Replacement Thread Inserts {0676}
Using Caterpillar Replacement Thread Inserts {0676}

Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}

Operating Instructions for Cat 1U-9400 Series Hydraulic Test Center {0784}
Operating Instructions for Cat 1U-9400 Series Hydraulic Test Center {0784}

Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}

Accumulator Discharging and Charging Procedures {0738, 4263, 4264, 4331, 5077, 5077, 5081, 7474}
Accumulator Discharging and Charging Procedures {0738, 4263, 4264, 4331, 5077, 5077, 5081, 7474}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Tool Operating Manual

Using The Inspection Borescopes 1U5268 and 8T9290 Borescopes
Using The Inspection Borescopes 1U5268 and 8T9290 Borescopes

Instructions for 1U9801 Ultrasonic Wear Indicator Program Module Replacement{0767}
Instructions for 1U9801 Ultrasonic Wear Indicator Program Module Replacement{0767}

9U7990 Counter Bore Tool Group for 3176, 3300 and 3400 Series Engines{1201}
9U7990 Counter Bore Tool Group for 3176, 3300 and 3400 Series Engines{1201}

Using the Caterpillar Fuel Flow Monitor System{0782, 1000, 1250}
Using the Caterpillar Fuel Flow Monitor System{0782, 1000, 1250}

358-4528 (380/480 V, 50/60 Hz, 3 Phase), 457-6040 (230V, 60 Hz, Single Phase) , 457-6039 (230V, 50 Hz, Single Phase) Hose Machine Group Set-Up and Operation{0599, 0684}
358-4528 (380/480 V, 50/60 Hz, 3 Phase), 457-6040 (230V, 60 Hz, Single Phase) , 457-6039 (230V, 50 Hz, Single Phase) Hose Machine Group Set-Up and Operation{0599, 0684}

Crimputer III Setup and Operation{0684, 5057}
Crimputer III Setup and Operation{0684, 5057}

NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}
NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}

9U-7840 Fuel Injection Equipment Calibration Fluid Test Kit{0374, 0599, 0706}
9U-7840 Fuel Injection Equipment Calibration Fluid Test Kit{0374, 0599, 0706}

NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}
NEHS1126: 370-8570 Bulk Fuel Filtration Group 200 GPM Flow Rate {0599, 0680, 0706, 0782, 1250, 1280}

370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}
370-8569 Bulk Fuel Filtration Group 100 GPM Flow Rate{0599, 0680, 0706, 0782, 1250, 1280}

439-3938, 439-3939, 439-3940, 439-3941, 439-3942, 439-3943 Link Bracket Assemblies {0374, 0599, 0632, 0700, 7000}
439-3938, 439-3939, 439-3940, 439-3941, 439-3942, 439-3943 Link Bracket Assemblies {0374, 0599, 0632, 0700, 7000}

NEHS0566 4C-9832 Large Engine Roll-Over Stand {0599, 0701}
NEHS0566 4C-9832 Large Engine Roll-Over Stand {0599, 0701}

Using the 9U-7868 and 9U-7869 Spanner Wrench to Remove and install Threaded Gland Cylinder Heads{0374, 0599, 0602, 0738}
Using the 9U-7868 and 9U-7869 Spanner Wrench to Remove and install Threaded Gland Cylinder Heads{0374, 0599, 0602, 0738}

185-5321 Cylinder Head Lifting Hook Assembly{0599, 0632, 0703, 1101, 6459}
185-5321 Cylinder Head Lifting Hook Assembly{0599, 0632, 0703, 1101, 6459}

Crimping Permanent Couplings Using the 136-3642 Crimp Tool Group in Combination and XT Hose Machines{0374, 0599, 0684, 5057}
Crimping Permanent Couplings Using the 136-3642 Crimp Tool Group in Combination and XT Hose Machines{0374, 0599, 0684, 5057}

Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}
Crimping 1028 Thermoplastic Hose, 2760 Reduced Diameter Thermoplastic Hose, and 1543 Air Conditioning Hose{0374, 0599, 0684, 1808, 1812, 7554}

456-4449 Support Device{0374, 0599, 0629, 0632, 0700}
456-4449 Support Device{0374, 0599, 0629, 0632, 0700}

Installing 457-6030 (C3-290 Controller) on Hose Crimping Machines 233-8048, 286-4354, 286-4355, 275-6199, 286-4353, and 233-8038{0374, 0599, 0684, 0700, 0738, 5057}
Installing 457-6030 (C3-290 Controller) on Hose Crimping Machines 233-8048, 286-4354, 286-4355, 275-6199, 286-4353, and 233-8038{0374, 0599, 0684, 0700, 0738, 5057}

20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}
20 GPM Portable Fuel Filtration System {0374, 0599, 0706, 1250, 1256, 1261}

464-0265 Lifting Bracket Assembly{0374, 0599, 0629, 0632, 0700, 0708, 1353}
464-0265 Lifting Bracket Assembly{0374, 0599, 0629, 0632, 0700, 0708, 1353}

General Usage for all Shackle Types{0374, 0599, 0629, 0632, 1122, 6459, 7000}
General Usage for all Shackle Types{0374, 0599, 0629, 0632, 1122, 6459, 7000}

442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122}
442-1750 Lifting Plate{0374, 0599, 0629, 0632, 0700, 1122}

Zip-Tie Installation Guide{0374, 0599, 7000}
Zip-Tie Installation Guide{0374, 0599, 7000}

NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}
NEHS1227: 477-3197 C27 Piston Ring Gauge Group {0374, 0599, 0700, 0701, 1214, 1215}

{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}
{0374, 0599, 0629, 0632, 0700, 0701, 1100, 1101}

NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}
NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}

M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}
M0077220 (NEHS1231) 115V & 230V Battery Chargers {1401, 751B}

Base Mounted Recirculating Parts Washers {0374, 0599, 0680, 0699, 0700}
Base Mounted Recirculating Parts Washers {0374, 0599, 0680, 0699, 0700}

Portable Aqueous Based Parts Cleaners, Models 482-9830, 482-9831, and 482-9832 {0374, 0599, 0680, 0699}
Portable Aqueous Based Parts Cleaners, Models 482-9830, 482-9831, and 482-9832 {0374, 0599, 0680, 0699}

Reuse And Salvage Guidelines

Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}
Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}

Dynamometer Testing of Caterpillar Engines {0781, 1000}
Dynamometer Testing of Caterpillar Engines {0781, 1000}

Using Lock-N-Stitch Procedures for Casting Repair {0676, 0685}
Using Lock-N-Stitch Procedures for Casting Repair {0676, 0685}

Reuse & Salvage for Valvetrain Components {1102, 1108, 1109, 1121, 1123}
Reuse & Salvage for Valvetrain Components {1102, 1108, 1109, 1121, 1123}

Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}
Using the 9U-5383 Vacuum Tester {0774, 0781, 1000, 1100}

Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}

Crimputer III Setup and Operation{0684, 5057}
Crimputer III Setup and Operation{0684, 5057}

Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}
Caterpillar Service Welding Guide {0374, 0599, 0677, 0678, 0679}

Fundamentals of HVOF Spray for Reconditioning Components {0599, 0679, 1000, 7000}
Fundamentals of HVOF Spray for Reconditioning Components {0599, 0679, 1000, 7000}

Fundamentals of Flame Spray for Reconditioning Components {0100, 0599, 0679}
Fundamentals of Flame Spray for Reconditioning Components {0100, 0599, 0679}

Cleaning Components with Carbon Dioxide (CO2) {0680, 1000, 7000}
Cleaning Components with Carbon Dioxide (CO₂) {0680, 1000, 7000}

Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}
Guideline for Proper Gasket Handling and Installation {0599, 0648, 0681, 1000, 7555}

Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}

Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}
Reuse and Salvage Guidelines Subscriptions {0374, 0599, 1000, 7000}

Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}
Scrap Barrel Analysis {0374, 0599, 0700, 0701, 0738, 1000, 7000}

Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}
Fundamentals of Plasma Transferred Wire Arc (PTWA) Spray for Reconditioning Components {0374, 0599, 0679, 1000}

Shop Review

Engine Component Racks
Engine Component Racks

Engine Stands
Engine Stands

Bench Test Procedures

Dynamometer Testing of Caterpillar Engines {0781, 1000}
Dynamometer Testing of Caterpillar Engines {0781, 1000}

Technical Analysis

Technical Analysis 1 (TA1) Visual Inspection for Industrial Engine {0372, 1000, 7000, 753S, 7565}
Technical Analysis 1 (TA1) Visual Inspection for Industrial Engine {0372, 1000, 7000, 753S, 7565}

Service Magazine

6V2050 Tapered Rod Tool Group Available For Removal And Installation Of Bearings{1219,1218,1214}
1980/06/09

Use The 6V2056 Rod And 6V2057 Point To Find True Top Center{0653}
1980/07/14

Modification Of Puller Bolt Prevents Thread Damage During Removal Of Sleeve From Sleeve Metering Fuel System{0621,1251,1253}
1980/11/03

6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1981/02/23

Use 6V4089 Reamer Assembly To Clean Nozzle Bores{0622}
1981/04/27

Improvements To Optional Modification Of 5P4150 Nozzle Tester{0651,1254}
1981/08/17

FT1632 Bolt Used During Removal Of Sleeve From Sleeve Metering Fuel System{0621,1251,1253}
1981/08/31

6V3100 Diesel Timing Indicator Group Available To Check Engine/Fuel System Timing And Mechanical Advance During Operation{0653,1206,1156}
1981/08/31

Piston And Connecting Rod Assembly Storage Cabinet{0600}
1982/01/18

New Engine Testing And Adjusting Tools Give More Accuracy And Longer Service Life{0651}
1982/02/01

New 6V4818 Driver Available To Install Rack Bearings In Fuel Injection Pump Housings{0622}
1982/02/08

Use 6V6035 Hardness Tester On Crankshafts{0651,1202}
1982/02/22

Use New Special Instruction To Install 5P6595 Insert In Cylinder Liner Seats{1216,0621}
1982/05/03

Separate Valve Stem Gauges Available{0653,1000}
1982/06/07

New Address For Repair Of Diagnostic Tools{0650}
1982/06/14

6V6124 Calibration Coil Available To Calibrate And Check 6V4910 AC/DC Clamp-On Ammeter{0651}
1982/06/28

Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16

Vacuum Tester Checks For Leaks Between Valve Face and Seat{0651,1103,1105}
1982/09/06

Dial Bore Gauge And Size Setting Fixture Available{0653}
1982/09/20

New Tool Makes Installation Of Carbon Stop Seals Easier{0622,1254}
1982/10/04

Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11

Use 6V6147 Polishing Wheel To Clean Piston Pins{0675,1214}
1982/11/08

6V6175 And 6V6176 Torque Adapters Make Installation Of Fuel Pump Drive Gear Easier{1206,1272,0614}
1982/11/08

Make Change To 6V2100 Multitach And 5P9698 Calibrator{0651}
1982/11/15

Service Parts Available For The 5P4150 Nozzle Testing Group{0651,0652}
1982/11/22

New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip {0653,1216,1105}
1982/11/29

Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16

6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1983/12/05

Correct Use Of The 6V4141 Sleeve Metering Calibration Tool Group{0600,0766,0778}
1984/10/01

Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27

Check 5P7435 Tee Adapter Groups In The 6V3100 Engine Timing Indicator Groups{0782}
1985/06/03

Higher Torque Can Be Used With 6V6980 Nozzle Puller Group{0706,1254}
1985/06/10

Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07

Fuel Sulfur Analyzer Available{0651,1280,1318}
1986/01/13

Update Information For Caterpillar Fuel Injection Equipment Test Stand{0782}
1986/06/16

New Engine Timing Indicator Group Available {0781,0782}
1986/07/07

New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27

Use Gas Detector Tubes That Have Expired Dates To "Break In" The Combustion Chambers For The Fuel Sulphur Analyzer Group{0651}
1986/11/10

Check For Dirt Before Replacing Pyrometer Switch{1050,7466}
1986/12/15

New Special Instruction For Troubleshooting 5P2150 Engine Horsepower Meter{0651,1250}
1977/01/17

New Tie Bars Improve Stability Of The Fuel Injection Test Bench{0652}
1977/01/17

New 5P7307 Engine Turning Tool Group Fits All Engines{0611}
1977/02/14

Tools Now Available To Ream And/Or Hone 0.500" (12.70 mm) Diameter Valve Guides{0663}
1977/08/22

Troubleshooting The Tachometer System Of The 4S6553 Engine Instrument Group{0651}
1977/10/10

Fabricated Extension Prevents Fuel "Splash" During Injection Valve Testing{0650,1254}
1977/10/17

Assembly Procedure For The 5P4721 Tube (Part Of The 5P4149 Conversion Group And 5P4150 Nozzle Testing Group){0650}
1977/10/24

With New 5P7448 Adapter, Earlier Fuel Injection Valves And Nozzles Can Be Tested And Adjusted On The 5P4150 Nozzle Testing Group{0651,1254}
1977/10/31

New 8T5261 Bushing Installer And Remover Adapter Tool Available{0600}
1987/03/02

Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Black Light Leak Detection Kit Available For Oil, Fuel and Cooling Systems {0774,1250,1300,1350}
1987/05/11

The Caterpillar Fuel Flow Monitor System Available {0782,1000,1250}
1987/05/11

Two New Self-Powered Digital Tachometers And Signal Generator Available {7462}
1987/05/11

Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group {0781,1200,1350}
1987/07/20

5P8665 Cylinder Liner Puller Makes Liner Removal Easier And Faster{0621,1216}
1978/01/09

Replacement Seal Group For Water Pump Impeller Now Has All The Seal Parts Plus An Installation Tool{1361,0622}
1978/02/13

5P4149 Conversion Group To Become A Discontinued Item On October 1, 1978{0650,1254}
1978/03/27

Locating Bushings For The 5P3550 Rod Boring Machine Will Now Hold Tapered Piston Pin Bushings {0626}
1978/04/17

Use 6V100 Tool Arrangement To Remove And Install Piston Pin Bearings For Both Tapered And Standard Connecting Rods{0620,1218}
1978/04/24

Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24

New 5P8744 Adapter Assembly And Special Instruction Procedures For 5P4150 Nozzle Tester Group{0650}
1978/08/28

New Drive Adapters For Fuel Injection Test Bench{0650}
1978/09/11

Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25

Adjustment Procedures And Lubrication Recommendations For Drive Pulleys On Caterpillar Fuel Injection Test Bench{0652}
1978/09/25

4J7533 O-Ring Seals Now Available For Parts Service Of The 5P4150 Nozzle Tester Group{0651}
1978/10/09

Caterpillar Fuel Injection Test Bench Book{0374}
1978/10/16

Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16

New FT2253 Cable Assembly Drawing Available For Kent-Moore Fuel Injection Test Bench{0782}
1988/01/04

Extraction Tools For "Live Oil Sampling"{7770,0770,0781,0783,0784}
1988/04/18

Some Components Of The Variable Pulley And Adjustable Pulley On The Kent-Moore Fuel Injection Test Bench Are Available From Caterpillar{0782}
1988/04/18

New 1U9139 Universal Fuel Line Pickup Available{0775}
1988/05/23

Installation Of Valves For Live Oil Sampling{7770,0770,0781,0783,0784}
1988/06/06

New Frequency Meter Has Replaceable Voltage Droop Resistor{7471}
1988/08/08

Improved Pressure Gauge Sender Used{7450,7485}
1988/11/21

Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12

New 6V87 Gauge Measures Valve Stem Wear{0653,1105}
1979/01/08

Current Chart For Dynamometer Adapters{0651,1000}
1979/01/22

9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28

6V183 Gasket Now Available For Parts Service To Use On 5P4150 Or 8S2242 Nozzle Tester{0651}
1979/06/25

Caution Label Added To 5P4150 Nozzle Testing Group{0651}
1979/07/09

Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06

Quick Disconnect Coupling On Optional Modification Of 5P4150 Nozzle Tester Permits Faster Exchange Of Adapters{0651,1254}
1979/09/03

Fast Fuel Delivery Couplings And Fast Oil Change Couplings Are Available For All Caterpillar Equipment{0671,1273,1279,1325}
1979/10/08

Use The 6V2034 Micrometer Adapter To Measure Lip Thickness Of Engine Valves {0653,1105}
1979/10/29

Cylinder Pack Puller Groups Improved {0705,1239}
1993/01/18

New Hydraulic Wrenches and Pumps {0602, 0615}
2000/06/01

Diagnostic Cables and Harnesses Are Available {0785}
2014/08/11

Thermocouple Assembly (Exhaust) Measures Engine Exhaust Temperatures {0701, 0776, 0781}
2004/04/01

40 Power Microscope is Available for Inspecting Bearing Journals on Crankshafts {0777, 1202}
2006/01/16

Compatible Puller Stud and Hydraulic Cylinder Capacity Chart {0599, 7000, 7562}
Compatible Puller Stud and Hydraulic Cylinder Capacity Chart {0599, 7000, 7562}

A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785}
A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785}

A New Tool Operating Manual for Proper Zip-Tie Installation Is Now Available for All Caterpillar Products {0374, 0599, 7000}
2015/08/10

Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}
Military Electronic Technician (Military ET) Is Now Available For Military Personnel {0374, 0376, 0599, 1000, 7000, 7610, 7620}

Process to Print Collage Schematics {0374, 1000, 7000}
Process to Print Collage Schematics {0374, 1000, 7000}

Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}
Reuse And Salvage Has Updated Air Inlet Correction Factors for Dynamometer Testing {0769, 1052, 1087}

Caterpillar Parts SIS Catalog 3304 :

8F-9866 GREASE GUN AS

4L-1560 TOOL GROUP

3L-7679 SLIDE RAIL GROUP

6L-8402 HEAT SINK ASSEMBLY

3N-6094 EXCITER MODIFICATION SERVICE GROUP

6L-8402 HEAT SINK ASSEMBLY

5N-4513 CONNECTION GP-GENERATOR LEADS

5N-4261 PANEL GP-SERIES BOOST

NAME PLATES AND TRANSFERS

Truck sale:

854

Caterpillar 303/304 20 HD BUCKET, bucket, Construction
- bucket
MILTON CAT

30,000

Caterpillar 3304B, Stationary Generator Sets, Construction

30,000

Caterpillar 3304B, Stationary Generator Sets, Construction

FOLEY EQUIPMENT COMPANY

650

Caterpillar 303/304 ADAPTER SSL TO MHE, Schnellwechsler, Bau-Und Bergbauausrüstung
- Quick connectors
MILTON CAT

17.000

Caterpillar 3304, Stationäre Stromaggregate, Bau-Und Bergbauausrüstung
- Stationary Generator Sets
EMPIRE MACHINERY