RIPPER BULLDOZER AND BLADE TILT LINES (8S6922 N/S)--Part 1 of 3--Type 2 8R Bulldozer Serial No. 43K57, 96, 101 and 43K103-Up Part of Lines, Guards and Valves shown on Pages 34 and 34-1 8U

RIPPER BULLDOZER AND BLADE TILT LINES (8S6922 N/S)--Part 1 of 3--Type 2
8R Bulldozer Serial No. 43K57, 96, 101 and 43K103-Up
Part of Lines, Guards and Valves shown on Pages 34 and 34-1

c150518 UEG0063S

8S6922 RIPPER BULLDOZER AND BLADE TILT LINES Parts scheme

For full view, you need register

Parts for your 8U BULLDOZER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	9S-6842	[2]	HOSE ASSEM.
	5P-0179 H		HOSE 96.0 cm(37.80 in.)
2.	3S-8606	[2]	SLEEVE
13.	3S-4055	[2]	COUPLING (straight)
4.	9S-6843	[2]	HOSE ASSEM.
	5P-0178 H		HOSE 95 cm(37.4 in.)
5.	8S-6417	[2]	COUPLING ASSEM. (straight)
6.	4S-5414	[2]	SLEEVE
7.	2P-1278	[3]	UNION
8.	8J-6580 C	[1]	PLATE
10.	8S-4941 C	[2]	HOSE ASSEM.
	5P-0178 H		HOSE 367 cm(144 in.)
11.	8S-6417	[2]	COUPLING ASSEM. (straight)
12.	4S-5414	[2]	SLEEVE
13.	8S-4936	[2]	HOSE ASSEM.
	5P-0179 H		HOSE 354.33 cm(139.50 in.)
14.	3S-8606	[2]	SLEEVE
15.	8S-4055	[2]	COUPLING ASSEM. (straight)
16.	2P-1281	[4]	CONNECTOR
17.	8S-4955 J	[1]	PLATE
18.	9S-4605 C	[2]	HOSE ASSEM.
	8S-6391	[1]	COUPLING ASSEM. (90 degrees)
19.	3S-8606	[2]	SLEEVE
20.	5P-0179 H		HOSE 41.9 cm(16.50 in.)
	8S-4055	[1]	COUPLING ASSEM. (straight)
21.	4D-0355	[2]	ADAPTER
22.	8S-5627	[2]	HOSE ASSEM.
	8S-6393	[1]	COUPLING ASSEM. (90 degrees)
	8S-6417	[1]	COUPLING ASSEM. (straight)
23.	5P-0178 H		HOSE 42.6 cm(16.80 in.)
24.	4S-5414	[2]	SLEEVE
25.	2P-7215	[1]	ELBOW
26.	5D-8064	[1]	ADAPTER
27.	030-7947 C	[1]	ELBOW
	3J-1907 C	[1]	SEAL
28.	2P-1279	[4]	NUT
29.	7F-2050	[4]	NUT
	H		ORDER BY THE CENTIMETRE
	J		USE 7M7260 GASKET SOLUTION
	C		INDICATES CHANGE

#UEG0063S0111

8S-6922: RIPPER BULLDOZER AND BLADE TILT LINES

RIPPER BULLDOZER AND BLADE TILT LINES

RIPPER BULLDOZER AND BLADE TILT LINES (8S6922 N/S)--Part 2 of 3--Type 2
8R Bulldozer Serial No. 43K57, 96, 101 and 43K103-Up
Part of Lines, Guards and Valves shown on Pages 34 and 34-1

c150519 UEG0063S

For full view, you need register

Parts for your 8U BULLDOZER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	8S-5629	[1]	HOSE ASSEM.
	8S-4055	[2]	COUPLING ASSEM. (straight)
2.	3S-8606	[2]	SLEEVE
3.	5P-0179 C		HOSE 79.25 cm(31.20 in.)
4.	0T-0573	[11]	BOLT 7 cm(2.75 in.) long
5.	3B-4506	[20]	LOCKWASHER
6.	8S-5618	[2]	BLOCK
	6J-3575	[2]	SEAL
7.	4D-0355	[7]	ADAPTER
8.	0S-1619	[1]	BOLT (3 in. long)
	4B-4278	[1]	WASHER
	7S-3916	[1]	CLIP
	7S-3919	[1]	CLIP
9.	030-7943	[1]	FITTING
	3K-0360	[1]	SEAL
10.	8S-5619	[1]	HOSE ASSEM.
	8S-4055	[2]	COUPLING ASSEM.
11.	3S-8606	[2]	SLEEVE
12.	5P-0179 CH		HOSE 38.35 cm(15.10 in.)
13.	8S-4948	[2]	BLOCK
14.	6J-3600	[4]	SEAL
15.	9S-7474	[2]	HOSE ASSEM.
	8S-4055	[2]	COUPLING ASSEM. (Straight)
16.	3S-8606	[2]	SLEEVE
17.	8S-7240 H		GUARD 19 in.
18.	5P-0179 CH		HOSE 57.4 cm(22.60 in.)
19.	4D-0354	[4]	FITTING
	3K-0360	[1]	SEAL
20.	9S-2995	[1]	HOSE ASSEM.
	5P-0179 CH		HOSE 46.48 cm(18.30 in.)
	8S-4055	[1]	COUPLING ASSEM. (Straight)
21.	3S-8606	[2]	SLEEVE
22.	1P-8408	[1]	COUPLING ASSEM. (90 degrees)
23.	0L-1352	[8]	BOLT
24.	8S-4947	[2]	BLOCK
	C		INDICATES CHANGE
	H		ORDER BY THE CENTIMETRE

#UEG0063S0112

8S-6922: RIPPER BULLDOZER AND BLADE TILT LINES

RIPPER BULLDOZER AND BLADE TILT LINES

RIPPER BULLDOZER AND BLADE TILT LINES (8S6922 N/S)--Part 3 of 3--Type 2
8R Bulldozer Serial No. 43K57, 96, 101 and 43K103-Up
Part of Lines, Guards and Valves shown on Pages 34 and 34-1

c150520 UEG0063S

For full view, you need register

Parts for your 8U BULLDOZER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	8S-5628	[1]	HOSE ASSEM.
			(Includes)
	5P-0179 H		HOSE 393.7 cm(155 in.)
2.	3S-8606	[2]	SLEEVE
3.	8S-4055	[2]	COUPLING ASSEM. (straight)
4.	4D-0354	[2]	FITTING
			(Each Includes)
	3K-0360	[1]	SEAL
5.	8S-5625	[1]	HOSE ASSEM.
			(Includes)
	5P-0179 H		HOSE 407.6 cm(160.50 in.)
6.	3S-8606	[2]	SLEEVE
7.	8S-6391	[2]	COUPLING ASSEM. (90 degrees)
8.	4D-0355	[2]	ADAPTER
9.	8S-5623	[2]	HOSE ASSEM.
			(Each Includes)
	8S-6393	[2]	COUPLING ASSEM.
10.	5P-0178 H		HOSE 368.3 cm(145 in.)
11.	4S-5414	[2]	SLEEVE
12.	030-7947 C	[2]	ELBOW
13.	030-7942 C	[2]	ELBOW
14.	3J-1907 C	[4]	SEAL
	C		INDICATES CHANGE
	H		ORDER BY THE CENTIMETRE

#UEG0063S0113

6J-8003: SELECTOR VALVE GROUP

SELECTOR VALVE GROUP

6J8003 SELECTOR VALVE GROUP
Part of Lines, Guards and Valves Group shown on Page 34

c112385 UEG0063S

6J8003 SELECTOR VALVE GROUP Parts scheme

For full view, you need register

Parts for your 8U BULLDOZER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
	6J-8893	[1]	BODY GROUP
			Consisting of:
1.		[1]	BODY
2.		[1]	STEM
3.	1S-0087	[1]	SPRING
4.	0L-2070	[8]	BOLT
5.	3B-4506	[8]	LOCKWASHER
6.	6J-8353	[2]	RETAINER
7.	6F-6673	[2]	SEAL

#UEG0063S0114

6J-8004: SELECTOR VALVE GROUP

SELECTOR VALVE GROUP

6J8004 SELECTOR VALVE GROUP
Part of Lines, Guards and Valves Group shown on Page 34

c131906 UEG0063S

6J8004 SELECTOR VALVE GROUP Parts scheme

For full view, you need register

Parts for your 8U BULLDOZER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
	6J-8894	[1]	BODY GROUP
			Consisting of:
1.		[1]	BODY
2.		[1]	STEM
3.	9S-4191	[2]	PLUG
	3J-1907	[2]	SEAL
4.	0L-2070	[8]	BOLT
5.	3B-4506	[8]	LOCKWASHER
6.	6J-8353	[2]	RETAINER
7.	6F-6673	[2]	SEAL
8.	1S-0087	[1]	SPRING

#UEG0063S0115

5J-7219: TRUNNION AND CRANKCASE GUARD GROUP

TRUNNION AND CRANKCASE GUARD GROUP

5J7219 TRUNNION AND CRANKCASE GUARD GROUP
Effective with 8C Bulldozer Serial No. 77G173. FOR USE WITH REAR CABLE CONTROL OR HYDRAULIC CONTROL. For D8 Tractors
Serial No. 36A5106-Up & 46A19392-Up. Only separate parts serviced. When complete Group is required order 7J7044 shown on Page 39

c112387 UEG0063S

5J7219 TRUNNION AND CRANKCASE GUARD GROUP Parts scheme

For full view, you need register

Parts for your 8U BULLDOZER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	9M-0148	[1]	GUARD ASSEM.
2.	1B-4333	[12]	NUT
3.	3B-4516	[12]	LOCKWASHER
4.	1S-1884	[12]	BOLT
	1B-4333	[12]	NUT
	3B-4516	[12]	LOCKWASHER
5.	3J-1874	[2]	WEDGE
6.	1D-4625	[16]	BOLT
7.	4F-4421	[18]	WASHER
	5J-9595	[1]	TRUNNION ASSEM.
8.	3J-2445	[1]	GUSSET (R.H.)
	3J-2446	[1]	GUSSET (L.H.)
9.	3J-3510	[2]	GUSSET
10.	9M-0149	[1]	GUARD ASSEM.
11.	4J-1297	[1]	PLATE ASSEM. (L.H.)
	4J-1298	[1]	PLATE ASSEM. (R.H.)
12.	4J-1296	[2]	COVER
13.	3J-6484	[2]	BEARING
			(Parts of 4J1297 & 4J1298 Assem.)
14.	4J-1295	[2]	PIN
15.	0S-1587	[6]	BOLT
16.	3B-4508	[10]	LOCKWASHER
17.	4J-2513	[2]	CAP
18.	0S-1973	[2]	BOLT
19.	4B-4285	[4]	WASHER
20.	0V-0531	[4]	WASHER
21.	7B-3235	[4]	BOLT
22.	9H-5111	[2]	COVER ASSEM.
23.	3J-9008 H	[2]	TAPPING STRIP ASSEM.
	H		NOT PART OF 5J7219 TRUNNION AN

#UEG0063S0116

7J-7044: TRUNNION AND CRANKCASE GUARD GROUP

TRUNNION AND CRANKCASE GUARD GROUP

7J7044 TRUNNION AND CRANKCASE GUARD GROUP--Type 1
8S Bulldozer Serial No. 77G173-Up. FOR USE WITH HYDRAULIC CONTROL
For D8 Tractors Serial No. 36A4469-Up and 46A10725-Up

c112386 UEG0063S

7J7044 TRUNNION AND CRANKCASE GUARD GROUP Parts scheme

For full view, you need register

Parts for your 8U BULLDOZER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	9M-0148	[1]	GUARD ASSEM.
2.	1B-4333	[12]	NUT
3.	3B-4516	[12]	LOCKWASHER
4.	1S-1884	[12]	BOLT (3.75" long)
			-OR-
	4M-5131	[12]	BOLT (4.24" long)
			-OR-
	5S-5764	[11]	BOLT (4.75" long)
	1S-1884	[1]	BOLT (3.75" long)
	1A-1898	[12]	WASHER
5.	3J-1874	[2]	WEDGE
6.	1D-4625	[16]	BOLT
7.	4F-4421	[18]	WASHER
	7J-7042	[1]	TRUNNION ASSEM.
8.	7J-7043	[1]	GUSSET (R.H.)
	3J-2446	[1]	GUSSET (L.H.)
9.	3J-3510	[2]	GUSSET
10.	9S-9523	[1]	PLATE ASSEM. (R.H.)
11.	4J-1297	[1]	PLATE ASSEM. (L.H.)
	4J-1298	[1]	PLATE ASSEM. (R.H.)
12.	4J-1296	[2]	COVER
13.	3J-6484	[4]	BEARING
			(One Half Each in 4J1297 & 4J1298 Assem.)
14.	4J-1295	[2]	PIN
15.	0S-1587	[6]	BOLT
16.	3B-4508	[10]	LOCKWASHER
17.	4J-2513	[2]	CAP
18.	0S-1973	[2]	BOLT
19.	4B-4285	[4]	WASHER
20.	0V-0531	[4]	WASHER
21.	7B-3235	[4]	BOLT
22.	9H-5111	[2]	COVER ASSEM.

#UEG0063S0117

7J-7044: TRUNNION AND CRANKCASE GUARD GROUP

TRUNNION AND CRANKCASE GUARD GROUP

7J7044 TRUNNION AND CRANKCASE GUARD GROUP--Type 2
8S Bulldozer Serial No. 77G173-Up. FOR USE WITH HYDRAULIC CONTROL
For D8 Tractors Serial No. 36A4469-Up and 46A10725-Up

c154944 UEG0063S

For full view, you need register

Parts for your 8U BULLDOZER:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	3P-3388 C	[1]	GUARD ASSEM.
2.	1B-4333	[12]	NUT
3.	3B-4516	[12]	LOCKWASHER
4.	8H-5772 C	[1]	BOLT 3.75 in. (95.25 mm)long
	1D-4639 C	[11]	BOLT 4 in. (101.60 mm)long
	6P-8829 C	[12]	RETAINER
5.	3J-1874	[2]	WEDGE
6.	1D-4625	[16]	BOLT
7.	4F-4421	[18]	WASHER
8.	7J-7042	[1]	TRUNNION ASSEM.
			(Includes)
	7J-7043	[1]	GUSSET (R.H.)
	3J-2446	[1]	GUSSET (L.H.)
9.	3J-3510	[2]	GUSSET
10.	9S-9523	[1]	PLATE ASSEM. (R.H.)
11.	4J-1297	[1]	PLATE ASSEM. (L.H.)
	4J-1298	[1]	PLATE ASSEM. (R.H.)
12.	4J-1296	[2]	COVER
13.	3J-6484	[4]	BEARING
			(One Half Each in 4J1297 & 4J1298 Assem.)
14.	4J-1295	[2]	PIN
15.	0S-1587	[6]	BOLT
16.	3B-4508	[10]	LOCKWASHER
17.	4J-2513	[2]	CAP
18.	0S-1973	[2]	BOLT
19.	4B-4285	[4]	WASHER
20.	0V-0531	[4]	WASHER
21.	7B-3235	[4]	BOLT
22.	9H-5111	[2]	COVER ASSEM.
	C		INDICATES CHANGE

#UEG0063S0118

6J-9256: TRUNNION GP

TRUNNION GP

6J9256 TRUNNION GROUP
8A, 8R, 8S and 8U Bulldozers Serial No. 28E7291-Up,
43K1-Up, 44K1-Up, 45K1-Up, 69E1-Up & 20F1-Up. For D8 Tractors Serial No.
36A5106-Up and 46A19392-Up

c131907 UEG0063S