BASIC ENGINE
CYLINDER BLOCK GPSERVICE EQUIPMENT AND SUPPLIES
GASKET & SEAL KITSBASIC ENGINE
CRANKSHAFT GPFLYWHEEL GP
PISTON & ROD GP
FLYWHEEL GP
PISTON & ROD GP
FUEL SYSTEM
GOVERNOR GPBASIC ENGINE
CYLINDER BLOCK GP#UEG0089S0020
9L-9446: CYLINDER BLOCK GROUP
9L9446 CYLINDER BLOCK GROUP
Parts for your 3145 GEN SET ENGINE:
CATERPILLAR SIS#UEG0089S0021
GASKET KITS
GASKET KITS
Parts for your 3145 GEN SET ENGINE:
CATERPILLAR SIS#UEG0089S0022
CRANKSHAFT BEARING REPLACEMENTS
CRANKSHAFT BEARING REPLACEMENTS
Parts for your 3145 GEN SET ENGINE:
CATERPILLAR SIS#UEG0089S0023
CRANKSHAFT
CRANKSHAFT
Parts for your 3145 GEN SET ENGINE:
CATERPILLAR SISPos. | Part No | Qty | Parts name | Comments |
---|---|---|---|---|
1. | 9L-9032 | [1] | POINTER | |
2. | 9L-8127 | [1] | CRANKSHAFT ASSEM. | |
3. | 9L-8336 | [1] | SLEEVE | |
4. | 9L-9330 | [1] | GEAR (51 Teeth) | |
5. | 9L-8337 | [1] | KEY | |
(Parts of 9L8127 Crankshaft Assem.) | ||||
6. | 9L-8381 | [1] | BEARING (Thrust) | |
7. | 9L-7188 | [1] | SEAL (Rear) | |
8. | 9L-8338 | [4] | BEARING (Main) | |
9. | 9L-9185 | [1] | SEAL (Front) | |
10. | 9L-8339 | [1] | WASHER | |
11. | 8F-3152 | [1] | BOLT | |
12. | 9L-9282 | [1] | DAMPER ASSEM. |
#UEG0089S0024
8L-6378: FLYWHEEL GROUP
8L6378 FLYWHEEL GROUP
Serial No. 65P1 to 65P308 inclusive
Serial No. 65P1 to 65P308 inclusive
Parts for your 3145 GEN SET ENGINE:
CATERPILLAR SIS#UEG0089S0025
9L-8569: CONNECTING ROD AND PISTON GROUP
9L8569 CONNECTING ROD AND PISTON GROUP--8 Required
Also part of 9N1254 Short Block Group listed on Page 44B
Also part of 9N1254 Short Block Group listed on Page 44B
Parts for your 3145 GEN SET ENGINE:
CATERPILLAR SISPos. | Part No | Qty | Parts name | Comments |
---|---|---|---|---|
1. | 9L-9361 | [1] | PISTON GROUP (Standard) | |
9L-9670 | [1] | PISTON GROUP (.020" Oversize) | ||
9L-9298 | [1] | PISTON GROUP (.040" Oversize) | ||
2. | 9L-9316 | [1] | RING ASSEM. (Standard-Oil) | |
(Part of 9L9361 Group) | ||||
9L-9673 | [1] | RING ASSEM. | ||
(.020" Oversize-Oil) | ||||
(Part of 9L9670 Group) | ||||
9L-9323 | [1] | RING ASSEM. | ||
(.040" Oversize-Oil) | ||||
(Part of 9L9298 Group) | ||||
3. | 9L-9192 | [1] | RING (Standard-Compression) | |
(Part of 9L9361 Group) | ||||
9L-9674 | [1] | RING (.020" Oversize) | ||
(Part of 9L9670 Group) | ||||
9L-9146 | [1] | RING (.040" Oversize) | ||
(Part of 9L9298 Group) | ||||
4. | 1J-6473 | [2] | RING | |
5. | 9N-8002 RC | [1] | ROD ASSEM. | |
6. | 9L-8382 | [1] | BEARING | |
7. | 9L-8225 | [2] | BOLT | |
8. | 9L-7669 | [2] | NUT | |
9. | 9L-7651 | [1] | BEARING (service) | |
(Consists of 2 9L9324 Bearings) | ||||
9L-7788 CH | [1] | BEARING (.010 in. undersize) | ||
9L-7789 CH | [1] | BEARING (.020 in. undersize) | ||
10. | 9L-9889 | [1] | PIN | |
9L-9612 | [1] | PISTON RING GROUP | ||
(Consists of complete set of Rings for one Piston) | ||||
C | INDICATES CHANGE | |||
R | REMFG PART MAY BE AVAILABLE | |||
H | NOT PART OF 9L8569 CONNECTING |
#UEG0089S0026
3N-0740: FLYWHEEL GP
3N740 FLYWHEEL GROUP
Serial No. 65P309-Up
Serial No. 65P309-Up
Parts for your 3145 GEN SET ENGINE:
CATERPILLAR SIS#UEG0089S0027
9N-2142: CONNECTING ROD AND PISTON GROUP
9N2142 CONNECTING ROD AND PISTON GROUP
Part of 9N2136 Short Block Group listed on Page 44B
Part of 9N2136 Short Block Group listed on Page 44B
Parts for your 3145 GEN SET ENGINE:
CATERPILLAR SISPos. | Part No | Qty | Parts name | Comments |
---|---|---|---|---|
1. | 9L-9361 | [1] | PISTON GROUP (Standard) | |
9L-9670 | [1] | PISTON GROUP (.020" Oversize) | ||
9L-9298 | [1] | PISTON GROUP (.040" Oversize) | ||
2. | 9L-9316 | [1] | RING ASSEM. (Standard Oil) | |
(Part of 9L9361 Group) | ||||
9L-9673 | [1] | RING ASSEM. | ||
(.020" Oversize-Oil) | ||||
(Part of 9L9670 Group) | ||||
9L-9323 | [1] | RING ASSEM. | ||
(.040" Oversize-Oil) | ||||
(Part of 9L9298 Group) | ||||
3. | 9L-9192 | [1] | RING (Standard-Compression) | |
(Part of 9L9361 Group) | ||||
9L-9674 | [1] | RING (.020" Oversize) | ||
(Part of 9L9670 Group) | ||||
9L-9146 | [1] | RING (.040" Oversize) | ||
(Part of 9L9298 Group) | ||||
4. | 1J-6473 | [2] | RING | |
5. | 9N-0407 R | [1] | ROD ASSEM. | |
6. | 9L-8382 | [1] | BEARING | |
7. | 9L-8225 | [2] | BOLT | |
8. | 9L-7669 | [2] | NUT | |
9. | 9N-2601 | [1] | BEARING (service) | |
(Consists of 9N397 Bearings) | ||||
9L-7788 H | [1] | BEARING (.010 in. undersize) | ||
9L-7789 H | [1] | BEARING (.020 in. undersize) | ||
10. | 9L-9889 | [1] | PIN | |
9L-9612 | [1] | PISTON RING GROUP | ||
(Consists of complete set of Rings for one Piston) | ||||
C | INDICATES CHANGE | |||
R | REMFG PART MAY BE AVAILABLE | |||
H | NOT PART OF 9N2142 CONNECTION |
#UEG0089S0028
2N-2821: FUEL SYSTEM
FUEL SYSTEM (2N2821 N/S)--Part 1 of 2
Serial No. 65P1 to 65P308 inclusive
Fuel Pump Housing and Governor parts are shown on Page 20
See Page 15 for Gasket Kit
Serial No. 65P1 to 65P308 inclusive
Fuel Pump Housing and Governor parts are shown on Page 20
See Page 15 for Gasket Kit
Parts for your 3145 GEN SET ENGINE:
CATERPILLAR SISPos. | Part No | Qty | Parts name | Comments |
---|---|---|---|---|
1. | 2N-1985 | [1] | GEAR ASSEM. (36 teeth) | |
2. | 9M-9729 | [1] | SEAL | |
3. | Y | [1] | FUEL PUMP HOUSING AND GOVERNOR | |
(See Separate Illustration) | ||||
4. | 2B-2404 | [1] | CLIP | |
5. | 9L-9372 | [4] | LOCK | |
6. | 9L-8557 | [1] | TEE | |
7. | 9L-8374 | [1] | TUBE ASSEM. (Fuel Return-R.H.) | |
8. | 5K-9979 | [1] | FITTING | |
9. | 9L-8873 | [1] | CLAMP | |
10. | 1L-5081 | [1] | SPACER | |
11. | 1D-4717 | [1] | NUT | |
12. | 3B-4506 | [1] | LOCKWASHER | |
13. | 9L-8345 | [1] | TUBE ASSEM. (Fuel Return-R.H.) | |
14. | 9L-8373 | [1] | TUBE ASSEM. (Fuel Return-L.H.) | |
15. | 9L-8344 | [4] | CONNECTOR | |
16. | 9L-8095 | [2] | FITTING | |
17. | 9L-8387 | [2] | TUBE | |
18. | 9L-8248 | [2] | MANIFOLD ASSEM. | |
19. | 9L-8969 | [12] | CLAMP | |
20. | 9L-7675 C | [8] | ADAPTER ASSEM. | |
21. | 6F-4855 | [1] | SEAL | |
22. | 9L-8388 | [8] | SPACER | |
23. | 9L-8134 | [8] | CLAMP ASSEM. | |
24. | 9L-8970 | [8] | CLAMP | |
25. | 9L-8436 | [8] | BOOT | |
26. | 9L-9263 | [8] | NOZZLE ASSEM. | |
1H-1023 | [1] | SEAL | ||
27. | 9L-9099 | [1] | WASHER | |
28. | 9L-9098 | [1] | SEAL | |
29. | 9L-7652 C | [1] | SHAFT ASSEM. | |
9L-7663 CH | [8] | PROTECTIVE PLUG | ||
(Fuel Nozzle Inlet) | ||||
6H-3687 CH | [8] | PROTECTIVE CAP | ||
(Fuel Nozzle Tip) | ||||
(NOT SHOWN) | ||||
C | INDICATES CHANGE | |||
Y | SEPARATE ILLUSTRATION | |||
H | NOT PART OF FUEL SYSTEM |
#UEG0089S0029
2N-2821: FUEL SYSTEM
FUEL SYSTEM (2N2821 N/S)--Part 2 of 2
Serial No. 65P1 to 65P308 inclusive
Serial No. 65P1 to 65P308 inclusive
Parts for your 3145 GEN SET ENGINE:
CATERPILLAR SISPos. | Part No | Qty | Parts name | Comments |
---|---|---|---|---|
1. | 9L-7180 | [1] | PUMP ASSEM. (Fuel Transfer) | |
2. | 9L-8492 | [2] | PLUG | |
3. | 9L-8496 | [2] | TEE | |
4. | 9L-9271 | [1] | LINE ASSEM. (No. 1) | |
5. | 9L-9273 | [1] | LINE ASSEM. (No. 3) | |
6. | 9L-8472 | [1] | TUBE ASSEM. (Fuel Inlet) | |
7. | 9L-9275 | [1] | LINE ASSEM. (No. 5) | |
8. | 9L-9277 | [1] | LINE ASSEM. (No. 7) | |
9. | 9L-8715 | [4] | CLAMP | |
10. | 9L-9014 | [12] | SCREW | |
3B-4502 | [12] | LOCKWASHER | ||
11. | 5K-9979 | [1] | FITTING | |
12. | 9L-8713 | [3] | CLAMP | |
13. | 9L-8714 | [4] | CLAMP (Tapped) | |
14. | 9L-9278 | [1] | LINE ASSEM. (No. 8) | |
15. | 9L-9276 | [1] | LINE ASSEM. (No. 6) | |
16. | 9L-8716 | [3] | CLAMP (Tapped) | |
17. | 9L-9274 | [1] | LINE ASSEM. (No. 4) | |
18. | 9L-9160 | [1] | CLAMP ASSEM. | |
19. | 9L-9272 | [1] | LINE ASSEM. (No. 2) | |
20. | 8M-8157 | [1] | SEAL | |
21. | 8M-5260 | [1] | SEAL | |
22. | 0S-1618 | [3] | BOLT | |
3B-4505 | [3] | LOCKWASHER | ||
23. | 9L-8175 | [1] | GASKET | |
24. | 0S-1594 | [2] | BOLT | |
3B-4506 | [2] | LOCKWASHER | ||
25. | 9L-8868 | [1] | ELBOW | |
26. | 1J-9671 | [1] | SEAL | |
27. | 9L-8791 | [1] | SOLENOID | |
28. | 3J-7354 | [1] | SEAL | |
29. | 2N-2074 | [1] | CABLE ASSEM. |
Information:
BASIC ENGINE
CYLINDER BLOCK GP
Engine News
New Procedure And New Tool Can Be Used To Remove Cylinder Sleeves From The Cylinder Block
1983/08/17
1983/08/17
Special Instruction
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Installing Crankshaft Bearing Caps On 4.5" Bore V8 Direct Injection Engines{1200}
Installing Crankshaft Bearing Caps On 4.5" Bore V8 Direct Injection Engines{1200}
Installing Crankshaft Bearing Caps On 4.5" Bore V8 Direct Injection Engines{1200}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Installation Of Crankshaft Seals And Wear Sleeves{1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
Using the <NOBR> 6V-7840</NOBR> Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
Using the
Specifications
Reuse And Salvage Guidelines
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}
Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}
Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}
Reuse and Salvage for 3114, 3116, and 3126 Engine Series Cylinder Blocks {1201}
Reuse and Salvage for 3114, 3116, and 3126 Engine Series Cylinder Blocks {1201}
Reuse and Salvage for 3114, 3116, and 3126 Engine Series Cylinder Blocks {1201}
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}
Inspection and Reuse Guideline of Cylinder Liners in Cat Engines {0761, 1201, 1213, 1216, 1216}
Inspection and Reuse Guideline of Cylinder Liners in Cat Engines {0761, 1201, 1213, 1216, 1216}
Inspection and Reuse Guideline of Cylinder Liners in Cat Engines {0761, 1201, 1213, 1216, 1216}
Using the <NOBR> 6V-7840</NOBR> Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}
Using the
Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Cylinder Block Cleaning and Audit Procedure {0644, 0680, 0701}
Cylinder Block Cleaning and Audit Procedure {0644, 0680, 0701}
Cylinder Block Cleaning and Audit Procedure {0644, 0680, 0701}
Disassembly and Assembly
Service Magazine
New Procedure And New Tool Can Be Used To Remove Cylinder Sleeves From The Cylinder Block{1222,1223}
1983/08/08
1983/08/08