CYLINDER BLOCK AND COVERS (9S5780 N/S)--End View--Part 2 of 2 Serial No. 93N876 to 93N882 inclusive Refer also to Page 123 for special parts D7F

BASIC ENGINE

CYLINDER BLOCK GP

0. 9S-5780 CYLINDER B
1. 9S-5780 CYLINDER B
2. 9S-5780 CYLINDER B
3. 9S-5780 CYLINDER B
4. 9S-5780 CYLINDER B
5. 9S-5780 CYLINDER B
6. 9S-5780 CYLINDER B
7. 5S-6778 CYLINDER B
8. 2P-8776 CYLINDER B

CRANKSHAFT GP

9. 9S-5781 CRANKSHAFT
0. INFORMATION

TRACK-TYPE TRACTOR D7F TRACK-TYPE TRACTOR 93N
D7F TRACTOR / DIRECT DRIVE / 93N00001-01174 (MACHINE) UEG0169S D7F 93N (1969)

BASIC ENGINE

CYLINDER BLOCK GP

9S-5780 CYLINDER BLOCK AND COVERS

#UEG0169S0030

9S-5780: CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS (9S5780 N/S)--End View--Part 2 of 2
Serial No. 93N876 to 93N882 inclusive
Refer also to Page 123 for special parts

c135870 UEG0169S

9S5780 CYLINDER BLOCK AND COVERS Parts scheme

For full view, you need register

Parts for your D7F TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	9S-3187	[1]	LOCK
2.	0S-1594	[8]	BOLT
3.	2N-2753	[1]	COVER
	9H-4891	[1]	GASKET
4.	5S-8055	[1]	GASKET
5.	9S-8991	[1]	COVER ASSEM.
6.	0T-0101	[4]	STUD
7.	8S-6814	[2]	DOWEL
8.	3B-2460	[1]	STUD
			(Parts of 9S8991 Assem.)
9.	1B-4203	[6]	NUT
10.	3B-4506	[23]	LOCKWASHER
11.	1A-2029	[2]	BOLT (1.125" long)
	7H-7954	[1]	BOLT (2.125" long)
12.	9S-1796	[1]	TUBE ASSEM.
13.	8S-3995	[1]	GAUGE ASSEM.
14.	9S-1434	[1]	PIPE
	7S-1801	[1]	ANCHOR
15.	7S-1803	[1]	CAP ASSEM.
16.	9S-8926	[1]	SUPPORT ASSEM.
17.	2B-2994	[2]	DOWEL
18.	0S-1589	[4]	BOLT
	3B-4510	[4]	LOCKWASHER
19.	9S-6730	[2]	SHIM
	9S-6731	[2]	SHIM
	9S-7072	[2]	SHIM
20.	1D-4612	[4]	BOLT
21.	5H-1504	[4]	WASHER
22.	1A-5822	[3]	BOLT (2.75" long)
	9S-1366	[1]	BOLT (2.50" long)
23.	1D-5117	[4]	NUT
24.	3B-4508	[8]	LOCKWASHER
25.	9S-3188	[1]	LOCK
26.	9H-5919	[1]	COVER
	5S-9594	[1]	GASKET
27.	4M-4419	[1]	LOCK
28.	8S-1326	[1]	FITTING
	8F-8998	[1]	NUT
			(Part of 8S1326 Fitting)
29.	0T-0573	[5]	BOLT
30.	4B-7739	[1]	PLUG
31.	0S-1595	[4]	BOLT
32.	3B-2968	[2]	BOLT
	2J-3506	[2]	NUT
	2S-0115	[2]	WASHER
33.	1P-6074	[1]	SUPPORT ASSEM.
	7S-1234	[1]	BUSHING ASSEM.
34.	0L-1143	[9]	BOLT
35.	9S-8925	[1]	SUPPORT ASSEM.
36.	0S-1587	[9]	BOLT
37.	5M-9136	[1]	LOCK
38.	5M-9132	[1]	LOCK
39.	5M-9135	[1]	LOCK
40.	7M-7205	[1]	LOCK
41.	0S-1585	[4]	BOLT
42.	5M-9131	[1]	LOCK

#UEG0169S0031

9S-5780: CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS (9S5780 N/S)--Part 1 of 3
Serial No. 93N883 to 93N1007 inclusive. 5S6778 Cylinder Block parts are shown on Page 22
Note: 8S4636 Piston and Liner Group, consisting of: 1--Piston Assembly, 1--Liner and 2--Seal, is available

c112406 UEG0169S

For full view, you need register

Parts for your D7F TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	5S-6778 Y	[1]	BLOCK ASSEM.
			(See Separate Illustration)
2.	9S-6557	[6]	LINER
	5S-6670	[12]	SEAL
3.	9S-1796	[1]	TUBE ASSEM.
4.	8S-3995	[1]	GAUGE ASSEM.
5.	8M-3023	[6]	ORIFICE
6.	7S-1803	[1]	CAP ASSEM.
7.	1P-6784 C	[1]	PIPE
	7S-1801	[1]	ANCHOR
	5S-8055	[1]	GASKET
8.	2H-5330 C	[2]	BOLT
9.	3B-4506	[57]	LOCKWASHER
10.	1A-2029 C	[1]	BOLT
11.	5M-6213	[6]	PLUG
12.	4M-2969	[1]	GASKET
13.	8S-1961	[1]	PLATE ASSEM.
	8S-1962	[1]	NUT
	8M-5362	[7]	BOSS
14.	0L-1351	[26]	BOLT
15.	8M-9307	[1]	PLUG
	6F-7062	[1]	GASKET
16.	9S-1799	[1]	COVER
	8S-0877	[1]	GASKET
17.	9S-1759	[1]	TUBE
18.	3B-8998	[2]	FITTING
	1F-1344	[1]	NUT
19.	0S-1591	[13]	BOLT (1.50 long)
	2A-4639	[7]	BOLT (1.625" long)
20.	4B-4278	[28]	WASHER
21.	5B-8030	[1]	SPACER
22.	8S-1326	[1]	FITTING
	8F-8998	[1]	NUT
23.	4B-7739	[1]	PLUG
24.	0L-1352	[3]	BOLT
25.	0T-0573	[5]	BOLT
26.	9S-5417	[1]	PAN
27.	8S-1965	[1]	GASKET
	C		INDICATES CHANGE
	Y		SEPARATE ILLUSTRATION

#UEG0169S0032

9S-5780: CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS (9S5780 N/S)--Part 2 of 3
Serial No. 93N883 to 93N1007 inclusive
See Page 24 for Gasket Kits. Refer also to Page 123 for special parts

c112407 UEG0169S

For full view, you need register

Parts for your D7F TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Qty	Parts name
1.	[9]	BOLT
2.	[17]	LOCKWASHER
3.	[1]	COVER ASSEM.
4.	[1]	STUD
5.	[2]	DOWEL
6.	[4]	STUD
7.	[1]	COVER
	[1]	GASKET
8.	[2]	BOLT
9.	[1]	GASKET
10.	[1]	PLATE ASSEM.
	[1]	STUD
11.	[6]	NUT
12.	[1]	GASKET
13.	[1]	SEAL
14.	[1]	TUBE ASSEM.
	[1]	BOLT
	[1]	LOCK
15.	[1]	COVER
16.	[3]	BOLT
17.	[4]	NUT
18.	[8]	LOCKWASHER
19.	[1]	GASKET
20.	[1]	BOLT
21.	[4]	BOLT
22.	[1]	SUPPORT ASSEM.
23.	[1]	BUSHING ASSEM.
24.	[2]	BOLT
25.	[2]	NUT
26.	[2]	WASHER
27.	[1]	LOCK (3 hole-5.04" long)
	[1]	LOCK (3 hole-4.50" long)
	[1]	LOCK (2 hole-3.31" long)
	[8]	BOLT

#UEG0169S0033

9S-5780: CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS (9S5780 N/S)--Part 3 of 3
Serial No. 93N883 to 93N1007 inclusive

c147146 UEG0169S

For full view, you need register

Parts for your D7F TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	9S-8925	[1]	SUPPORT ASSEM.
2.	8M-3107	[1]	COVER
	2S-4750	[1]	GASKET
3.	0S-1594	[12]	BOLT
	3B-4506	[12]	LOCKWASHER
4.	9S-7036	[1]	HOUSING ASSEM.
5.	3F-0957	[4]	DOWEL
6.	9S-6729	[2]	BEARING
7.	7L-4265	[2]	WASHER
8.	5M-6214	[2]	PLUG
9.	3F-6795	[6]	DOWEL
10.	3D-0490	[12]	STUD
11.	2A-3798	[2]	DOWEL
12.	9H-5921	[1]	GASKET
13.	4B-3938	[1]	PLUG
14.	0S-1589	[4]	BOLT
	3B-4510	[4]	LOCKWASHER
15.	9S-8926	[1]	SUPPORT ASSEM.
	2B-2994	[2]	DOWEL
16.	9S-6730	[2]	SHIM (.049" Thick)
	9S-6731 C	[2]	SHIM (.065" Thick)
	9S-7072	[2]	SHIM (.083" Thick)
17.	1D-4612	[4]	BOLT
	5H-1504	[4]	WASHER
18.	2A-3798	[2]	DOWEL
19.	5M-9132	[1]	LOCK
20.	0S-1587	[9]	BOLT
21.	5M-9135	[1]	LOCK
22.	7M-7205	[1]	LOCK
23.	0S-1585	[4]	BOLT
24.	5M-9131	[1]	LOCK
25.	5M-9136	[1]	LOCK
	C		INDICATES CHANGE

#UEG0169S0034

9S-5780: CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS (9S5780 N/S)--Part 1 of 3
Serial No. 93N1008-Up
2P8776 Cylinder Block parts are shown on Page 22A

c140082 UEG0169S

For full view, you need register

Parts for your D7F TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	2P-8776 YC	[1]	BLOCK ASSEM.
			(Separate Illustration)
2.	2P-8889 C	[6]	LINER
	5S-6670 C	[18]	SEAL
3.	9S-1796	[1]	TUBE ASSEM.
4.	8S-3995	[1]	GAUGE ASSEM.
5.	8M-3023	[6]	ORIFICE
6.	7S-1803	[1]	CAP ASSEM.
7.	1P-6784	[1]	PIPE
	7S-1801	[1]	ANCHOR
	5S-8055	[1]	GASKET
8.	2H-5330	[2]	BOLT
9.	3B-4506	[57]	LOCKWASHER
10.	1A-2029	[1]	BOLT
11.	5M-6213	[6]	PLUG
12.	4M-2969	[1]	GASKET
13.	8S-1961	[1]	PLATE ASSEM.
	8S-1962	[1]	NUT
	8M-5362	[7]	BOSS
14.	0L-1351	[26]	BOLT
15.	8M-9307	[1]	PLUG
	6F-7062	[1]	GASKET
16.	9S-1799	[1]	COVER
	8S-0877	[1]	GASKET
17.	9S-1759	[1]	TUBE
18.	3B-8998	[2]	FITTING
	1F-1344	[1]	NUT
19.	0S-1591	[13]	BOLT (1.50" Long)
	2A-4639	[7]	BOLT (1.625" Long)
20.	4B-4278	[28]	WASHER
21.	5B-8030	[1]	SPACER
22.	8S-1326	[1]	FITTING
	8F-8998	[1]	NUT
23.	4B-7739	[1]	PLUG
24.	0L-1352	[3]	BOLT
25.	0T-0573	[5]	BOLT
26.	9S-5417	[1]	PAN
27.	8S-1965	[1]	GASKET
28.	5M-6214 C	[1]	PLUG
	C		INDICATES CHANGE
	Y		SEPARATE ILLUSTRATION

#UEG0169S0035

9S-5780: CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS (9S5780 N/S)--Part 2 of 3
Serial No. 93N1008-Up. See Page 24 for Gasket Kits
Refer also to Page 123 for special parts

c112407 UEG0169S

For full view, you need register

Parts for your D7F TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Qty	Parts name
1.	[9]	BOLT
2.	[17]	LOCKWASHER
3.	[1]	COVER ASSEM.
4.	[1]	STUD
5.	[2]	DOWEL
6.	[4]	STUD
7.	[1]	COVER
	[1]	GASKET
8.	[2]	BOLT
9.	[1]	GASKET
10.	[1]	PLATE ASSEM.
	[1]	STUD
11.	[6]	NUT
12.	[1]	GASKET
13.	[1]	SEAL
14.	[1]	TUBE ASSEM.
	[1]	BOLT
	[1]	LOCK
15.	[1]	COVER
16.	[3]	BOLT
17.	[4]	NUT
18.	[8]	LOCKWASHER
19.	[1]	GASKET
20.	[1]	BOLT
21.	[4]	BOLT
22.	[1]	SUPPORT ASSEM.
23.	[1]	BUSHING ASSEM.
24.	[2]	BOLT
25.	[2]	NUT
26.	[2]	WASHER
27.	[1]	LOCK (3 hole-5.04" long)
	[1]	LOCK (3 hole-4.50" long)
	[1]	LOCK (2 hole-3.31" long)
	[8]	BOLT

#UEG0169S0036

9S-5780: CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS

CYLINDER BLOCK AND COVERS (9S5780 N/S)--Part 3 of 3
Serial No. 93N1008-Up

c147148 UEG0169S

For full view, you need register

Parts for your D7F TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	9S-8925	[1]	SUPPORT ASSEM.
2.	8M-3107	[1]	COVER
	2S-4750	[1]	GASKET
3.	0S-1594	[12]	BOLT
	3B-4506	[12]	LOCKWASHER
4.	2P-4691 C	[1]	HOUSING ASSEM.
5.	3F-0957	[4]	DOWEL
6.	9S-6729	[2]	BEARING
7.	7L-4265	[2]	WASHER
8.	5M-6214	[2]	PLUG
9.	3F-6795	[6]	DOWEL
10.	3D-0490	[12]	STUD
11.	2A-3798	[2]	DOWEL
12.	9H-5921	[1]	GASKET
13.	4B-3938	[1]	PLUG
14.	0S-1589	[4]	BOLT
	3B-4510	[4]	LOCKWASHER
15.	9S-8926	[1]	SUPPORT ASSEM.
	2B-2994	[2]	DOWEL
16.	9S-6730	[2]	SHIM (.049" Thick)
	9S-6731 C	[2]	SHIM (.065" Thick)
	9S-7072	[2]	SHIM (.083" Thick)
17.	1D-4612	[4]	BOLT
	5H-1504	[4]	WASHER
18.	2A-3798	[2]	DOWEL
19.	5M-9132	[1]	LOCK
20.	0S-1587	[9]	BOLT
21.	5M-9135	[1]	LOCK
22.	7M-7205	[1]	LOCK
23.	0S-1585	[4]	BOLT
24.	5M-9131	[1]	LOCK
25.	5M-9136	[1]	LOCK
	C		INDICATES CHANGE

#UEG0169S0037

5S-6778: CYLINDER BLOCK ASSEMBLY

CYLINDER BLOCK ASSEMBLY

5S6778 CYLINDER BLOCK ASSEMBLY
Serial No. 93N1 to 93N1007 inclusive. Part of Cylinder Block and Covers shown on
Pages 20, 20B and 20D. Note: For Field Replacement order 5S6778 Block plus 1--9S5603 Hardware Kit

c112398 UEG0169S

5S6778 CYLINDER BLOCK ASSEMBLY Parts scheme

For full view, you need register

Parts for your D7F TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	7M-4046	[ 4]	BEARING
2.	5M-6213	[ 1]	PLUG
3.	8B-1312	[ 2]	DOWEL
4.	4B-5387	[ 2]	PLUG
5.	1H-0974	[ 1]	DOWEL
6.	5B-7652	[ 2]	DOWEL
7.	8S-0835	[ 1]	DOWEL
8.	3S-8313	[ 2]	PLUG
9.	8B-6349	[ 2]	DOWEL
10.	5S-8462	[ 1]	STUD
11.	9M-5477	[ 1]	BEARING
12.	4B-9782	[ 1]	BALL
13.	7S-3224	[ 14]	BOLT
	2S-5658	[ 14]	WASHER
14.	8S-4676	[ 7]	BEARING CAP GROUP
	8S-4674	[ 2]	SHIM (long)
	8S-4673	[ 6]	SHIM (short)
			-OR-
	1P-2717	[ 7]	BEARING CAP

#UEG0169S0038

2P-8776: CYLINDER BLOCK AS

CYLINDER BLOCK AS

2P8776 CYLINDER BLOCK ASSEMBLY
Serial No. 93N1008-Up. Part of Cylinder Block and Covers shown on Page 20G
Note: For Field Replacement order 2P8776 Block plus 1--2P8782 Hardware Kit

c114554 UEG0169S

For full view, you need register

Parts for your D7F TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Part No	Qty	Parts name
1.	7M-4046	[4]	BEARING
2.	5M-6213	[1]	PLUG
3.	8B-1312	[2]	DOWEL
4.	4B-5387	[2]	PLUG
5.	1H-0974	[1]	DOWEL
6.	5B-7652	[2]	DOWEL
7.	8S-0835	[1]	DOWEL
8.	3S-8313	[2]	PLUG
9.	8B-6349	[2]	DOWEL
10.	5S-8462	[1]	STUD
11.	9M-5477	[1]	BEARING
12.	4B-9782	[1]	BALL
13.	7S-3224	[14]	BOLT
	2S-5658	[14]	WASHER
14.	1P-2717	[7]	BEARING CAP

#UEG0169S0039

9S-5781: CRANKSHAFT

CRANKSHAFT

CRANKSHAFT (9S5781 N/S)
Serial No. 93N1 to 93N968 inclusive

c112408 UEG0169S

For full view, you need register

Parts for your D7F TRACK-TYPE TRACTOR:

CATERPILLAR SIS

Pos.	Qty	Parts name
1.	[2]	PLATE
2.	[1]	CRANKSHAFT ASSEM.
3.	[6]	PLUG
4.	[1]	KEY
5.	[1]	GEAR (40 Teeth)
6.	[7]	BEARING
7.	[1]	SEAL
8.	[6]	BOLT
	[6]	LOCKWASHER
9.	[1]	DAMPER ASSEM.
10.	[1]	GEAR (50 Teeth)
11.	[1]	PULLEY
12.	[1]	BOLT
13.	[1]	WASHER
14.	[1]	SEAL

Information:

BASIC ENGINE

CYLINDER BLOCK GP

Special Instruction

Using Caterpillar Cylinder Pack Pulling Tools{1239}
Using Caterpillar Cylinder Pack Pulling Tools{1239}

Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}
Pressure Lubrication Procedure for Remanufactured Engines and Short Blocks{1000, 1200, 1020}

3306 Cylinder Head To Block Joint Repair Procedure{1124, 1101, 1201}
3306 Cylinder Head To Block Joint Repair Procedure{1124, 1101, 1201}

Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}
Use Of 5P8709 Tool Group For Alignment Of Piston Cooling Jets{1331}

Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}

Installation Of 1N3574 Or 1N3576 Cylinder Block Service Group (Spacer Plate) As A Replacement For The Former Counterbored Cylinder Block{1201}
Installation Of 1N3574 Or 1N3576 Cylinder Block Service Group (Spacer Plate) As A Replacement For The Former Counterbored Cylinder Block{1201}

Installation Of Crankshaft Seals And Wear Sleeves{1203}
Installation Of Crankshaft Seals And Wear Sleeves{1203}

Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}
Use Of 1P4000 Line Boring Tool Group{0672, 1201, 1203}

Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}
Installing Heli-Coil Inserts In Caterpillar Cylinder Heads{1117}

Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}
Pressure Lubrication Procedure For Remanufactured Engines And Short Blocks{1000, 1201}

Use Of 8T0455 Cylinder Liner Projection Indicator Group{0760, 1216}
Use Of 8T0455 Cylinder Liner Projection Indicator Group{0760, 1216}

Cylinder Block Cleaning Procedure{1201}
Cylinder Block Cleaning Procedure{1201}

Installation Of 0R2554 Remanufactured Short Block Group{1200}
Installation Of 0R2554 Remanufactured Short Block Group{1200}

Using 5P4175 Boring Tool Group And 5P1618 Tool Arrangement{0672, 1200}
Using 5P4175 Boring Tool Group And 5P1618 Tool Arrangement{0672, 1200}

Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}

Using the <NOBR> 6V-7840</NOBR> Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}

Service Letter-NACD

Cylinder Head Gasket And Spacer Deck Gasket Replacement In Various Gasket Kits
Cylinder Head Gasket And Spacer Deck Gasket Replacement In Various Gasket Kits

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Brazil

Service Letter-Truck/Ag/Marine

Specifications

Cylinder Block
3306 VEHICULAR ENGINE

Cylinder Liner
3306 VEHICULAR ENGINE

Cylinder Liner Projection
3306 VEHICULAR ENGINE

Bearing Surface (Journal) For Main Bearings
3306 VEHICULAR ENGINE

Main Bearings And Connecting Rod Bearings
3306 VEHICULAR ENGINE

Tool Operating Manual

9U7990 Counter Bore Tool Group for 3176, 3300 and 3400 Series Engines{1201}
9U7990 Counter Bore Tool Group for 3176, 3300 and 3400 Series Engines{1201}

Setup and Operation of the 368-8645 Tool Kit (CRANKCASE PRESSURE){1317}
Setup and Operation of the 368-8645 Tool Kit (CRANKCASE PRESSURE){1317}

Using the 8T-2700 Blowby/Air Flow Indicator{0781, 0785, 1317}
Using the 8T-2700 Blowby/Air Flow Indicator{0781, 0785, 1317}

420-7630 Main Bearing Cap Lifting Device{0599, 0629, 0632, 0701, 1201, 1203, 1230}
420-7630 Main Bearing Cap Lifting Device{0599, 0629, 0632, 0701, 1201, 1203, 1230}

Using the 242-3980 Piston Groove Gauge on 3500A and B Engines with Monotherm Pistons using the 329-2630 and 329-2631 Piston Groove Gauges on 3500B Engines with Monotherm Pistons{0374, 0599, 0700, 0701, 0705}
Using the 242-3980 Piston Groove Gauge on 3500A and B Engines with Monotherm Pistons using the 329-2630 and 329-2631 Piston Groove Gauges on 3500B Engines with Monotherm Pistons{0374, 0599, 0700, 0701, 0705}

Service Letter-China

Cylinder Head Gasket And Spacer Deck Gasket Replacement In Various Gasket Kits
Cylinder Head Gasket And Spacer Deck Gasket Replacement In Various Gasket Kits

Service Letter-Asia

Reuse And Salvage Guidelines

Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}
Reuse and Salvage for Cast Iron Cylinder Blocks {1201, 1201}

Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}
Reuse and Salvage for 3176, 3300, 3400 & C-Series Engine Cylinder Blocks {0670, 0672, 0761, 1201, 7225}

Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}
Inspection and Reconditioning Procedures of Main Bearing Bores in Cylinder Blocks {1201, 1202, 1224, 1224}

Inspection and Reuse Guideline of Cylinder Liners in Cat Engines {0761, 1201, 1213, 1216, 1216}
Inspection and Reuse Guideline of Cylinder Liners in Cat Engines {0761, 1201, 1213, 1216, 1216}

Using the <NOBR> 6V-7840</NOBR> Deck Checking Tool Assembly {0701, 1201, 7225}
Using the 6V-7840 Deck Checking Tool Assembly {0701, 1201, 7225}

Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}
Cylinder Block Salvage Procedure Using Belzona® 1311 (Ceramic R Metal) {0700, 0701, 1000, 1201}

Cylinder Block Cleaning and Audit Procedure {0644, 0680, 0701}
Cylinder Block Cleaning and Audit Procedure {0644, 0680, 0701}

Service Letter-APD

Cylinder Head Gasket And Spacer Deck Gasket Replacement In Various Gasket Kits
Cylinder Head Gasket And Spacer Deck Gasket Replacement In Various Gasket Kits

Disassembly and Assembly

Crankshaft Main Bearings
D7F ENGINE

Cylinder Liners
D7F ENGINE

Camshaft Bearings
D7F ENGINE

Service Magazine

Spacer Plate Block Group Used For Parts Service Of Block Group With Counterbore Design{1101,1201}
1980/03/03

Use Of A Flex-Hone For Cylinder Liner Reconditioning{0664,0674,1216}
1981/12/21

Use New Special Instruction To Install 5P6595 Insert In Cylinder Liner Seats{1216,0621}
1982/05/03

Inspection Marks On Bearings{7551,1230,1226,1203,1219,1227}
1982/05/03

Service Information For Easier Use Of The 6V3100 Timing Indicator Group{0651,1250,1156,1157}
1982/10/11

Use FT1711 Light Table For Cylinder Liner Inspection {0652,1216}
1982/11/29

New 6V7059 Micrometer Measures Liner Top Flange And Valve Lip {0653,1216,1105}
1982/11/29

Procedure To Clean Oil Passages In Crankshafts And Cylinder Blocks{0622,0675,1201,1202}
1983/05/16

Reuse Of Engine Bearings{1230}
1983/05/16

Reuse Of Engine Bearings{1230,1219,1203}
1983/11/21

Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02

Bearing Failures On Engines Due To Lack Of Lubrication{1230,1219,1203,1202}
1986/09/08

New Indicator Instrument Group Available To Measure Crankcase Blowby And Radiator Air Velocity{0781,1200,1350}
1986/10/27

Cylinder Head Water Directors No Longer Needed In Direct Injection Engines {1115}
1987/03/09

Additional Guidelines For Using The 8T2700 Blowby/Air Flow Indicator Group {0781,1200,1350}
1987/07/20

5P8665 Cylinder Liner Puller Makes Liner Removal Easier And Faster{0621,1216}
1978/01/09

Use New Main Bearings In Replacement Cylinder Blocks{1203,1201}
1978/06/12

New Information On Reusable Cylinder Liners{1216}
1978/06/19

Change In Procedure To Check Main Bearing Clearance{1203}
1978/08/28

New Centering Rings For Oversized Main Bearings{0665,1230}
1979/06/04

New Specification For Installation Of Camshaft Front Bearing In Cylinder Block{1211}
1979/06/11

Improved Engine Design Uses Cylinder Block With Spacer Plate And New Crankshaft Thrust Plates{1000}
1979/07/02

Why Engines Are Damaged By Fuel Sulfur{1104,1216,1280,1318,1215}
1979/08/27

Pin Bore Is Now Offset (Not In The Center) .059" (1.5 mm) In The Piston To Stop Vibration Of The Cylinder Liners Which Can Cause Pitting On The Coolant Side Of The Cylinder Liners {1214,1216}
1979/09/10

Fuel Sulfur-Your Diesel's Silent Enemy{0375,1280}
1979/12/17

Use Only Stainless Steel Cylinder Liner Shims To Salvage Damaged 4.75" Bore Cylinder Blocks{1201,1216,1217}
1990/11/19

Remanufactured Camshafts And Cam Kits Available For Parts Service{1210,1211,1212}
1990/12/17

Checking Crankshaft Journal Surface Hardness On Remanufactured Crankshafts{1202}
1991/01/07

Correction For Camshaft And Valve Seat Specifications{1210,1103}
1992/07/20

Be Sure To Use Correct Cup Plugs On 0R2077, 0R2554, And 0R3258 Remanufactured Short Blocks{1200,1201}
1992/11/23

Cylinder Pack Puller Groups Improved {0705,1239}
1993/01/18

Caterpillar Parts SIS Catalog D7F :

9S-5780 CYLINDER BLOCK AND COVERS

5S-6687 CYLINDER HEAD AND VALVE MECHANISM

9S-5780 CYLINDER BLOCK AND COVERS

5S-6778 CYLINDER BLOCK ASSEMBLY

2P-8776 CYLINDER BLOCK AS

Truck sale:

CATERPILLAR D7F 1992
- TRACK TYPE TRACTORS
MILTON CAT
100 Quarry Drive - MILFORD - Massachus

CATERPILLAR D7F 1974
- TRACK TYPE TRACTORS
TOROMONT
For All your Used Equipment Needs - in Ontario, Manitoba, Newfoundlan

CATERPILLAR D7F 1972
- TRACK TYPE TRACTORS
FOLEY EQUIPMENT CO. (KS/MO)
1550 S. West Street - Wichita - Kansas

USD $27,500

CAT D7F

Powertrax Equipment Sales

USD $54,900

1971 CAT D7F

Construction Station
Wayne, Michigan