ELECTRICAL AND STARTING SYSTEM
STARTING MOTOR GPSOLENOID GP
SWITCH GP
ELECTRICAL AND STARTING SYSTEM
STARTING MOTOR GP#UEG0693S0060
4N-3182: STARTING MOTOR GP-ELECTRIC
4N3182 ELECTRIC STARTING MOTOR GROUP--Delco-Remy--24 Volt--Part 3 of 3
Part of 7S3622 Starting Motor Group shown on Page 31
Only separate parts serviced. When complete Group is required, order 4N3181
Part of 7S3622 Starting Motor Group shown on Page 31
Only separate parts serviced. When complete Group is required, order 4N3181
Parts for your 920 WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 4M-1855 | [1] | PLUNGER ASSEM. | |
| 2. | 2S-4027 | [1] | WASHER | |
| 3. | 4M-1829 | [1] | BOOT | |
| 4. | 4M-1828 | [1] | RETAINER | |
| 5. | 9M-7609 | [1] | SPRING | |
| 6. | 4M-1827 | [1] | RETAINER | |
| 7. | 1H-1023 | [1] | SEAL | |
| 8. | 4M-1850 | [1] | HOUSING ASSEM. | |
| (Includes) | ||||
| 9. | 9F-2547 | [1] | WICK | |
| 10. | 2B-4602 | [1] | PLUG | |
| 11. | 1M-9968 | [1] | BUSHING | |
| 12. | 2F-6678 | [1] | SEAL | |
| 13. | 2H-3429 | [2] | RING | |
| 14. | 4L-2729 | [1] | WASHER | |
| 15. | 4M-1853 | [1] | LEVER ASSEM. | |
| 16. | 3F-2617 | [1] | NUT | |
| 17. | 4M-1832 | [1] | GASKET | |
| 18. | 4M-1831 | [1] | PLUG | |
| 19. | 1S-0297 | [1] | HOUSING ASSEM. | |
| (Includes) | ||||
| 20. | 4M-1896 | [1] | BUSHING | |
| 21. | 4M-1833 | [5] | SCREW 1.50 in. (38.10 mm) long | |
| 7M-0336 | [1] | SCREW .875 in. (22.23 mm) long | ||
| 22. | 6N-3827 CA | [1] | DRIVE ASSEM. (480118) | |
| - OR - | ||||
| 2P-4708 C | [1] | DRIVE ASSEM. (1894213) | ||
| (Includes) | ||||
| 23. | 9S-9771 | [1] | PINION | |
| 24. | 4M-1854 | [1] | SHAFT | |
| 25. | 2D-6392 | [1] | SEAL | |
| 26. | 7F-4556 | [5] | BOLT | |
| 27. | 1L-4789 | [5] | LOCKWASHER | |
| 28. | 4M-0189 | [1] | SEAL | |
| 29. | 1M-9971 | [1] | SPACER | |
| 30. | 4M-1851 | [1] | GASKET | |
| THE FOLLOWING REPAIR KITS ARE AVAILABLE FOR 2P4708 DRIVE ASSEM. | ||||
| 7N-6098 C | [1] | KIT (spring) | ||
| (Includes Cup and Spring) | ||||
| 9S-9825 | [1] | KIT (Cup) | ||
| (Includes Cup and Washers) | ||||
| 4S-9459 | [1] | KIT (washer) | ||
| (Includes Cup and Washers) | ||||
| A | NOT PART OF THIS GROUP | |||
| C | INDICATES CHANGE | |||
#UEG0693S0061
4N-7905: STARTING MOTOR GP-ELECTRIC
4N7905 ELECTRIC STARTING MOTOR GROUP--Delco-Remy--24 Volt--Part 1 of 3
Part of 4N7199 Starting Motor Group shown on Page 30A. 6N5123 Switch parts are shown on Page 37
Only separate parts serviced. When complete Group is required order 4N7903
Part of 4N7199 Starting Motor Group shown on Page 30A. 6N5123 Switch parts are shown on Page 37
Only separate parts serviced. When complete Group is required order 4N7903
Parts for your 920 WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 7F-4556 | [4] | BOLT | |
| 2. | 1L-4789 | [4] | LOCKWASHER | |
| 3. | 4M-1844 | [1] | FRAME ASSEM. | |
| 4. | 7S-9826 | [1] | PLUG | |
| 5. | 3S-2398 | [1] | BUSHING | |
| 6. | 2B-4602 | [1] | PLUG | |
| 7. | 9F-2547 | [1] | WICK | |
| 8. | 2L-8166 | [1] | WASHER | |
| 9. | 4M-1868 | [1] | ARMATURE ASSEM. | |
| 10. | 3L-3380 | [1] | BUSHING | |
| 11. | 4M-1839 | [1] | COIL ASSEM. | |
| 12. | 9H-3757 | [2] | WASHER | |
| 13. | 7F-3494 | [1] | WASHER | |
| 14. | 4M-1841 | [1] | CONNECTOR | |
| 15. | 1D-5117 | [2] | NUT | |
| 16. | 6N-5123 YC | [1] | SWITCH ASSEM. | |
| (Separate Illustration) | ||||
| 17. | 6H-3622 | [4] | SCREW | |
| 18. | 3B-4508 | [1] | LOCKWASHER | |
| 19. | 3F-0379 | [8] | SCREW | |
| 20. | 2N-3145 | [1] | INSULATOR | |
| 21. | 4M-1831 | [2] | PLUG | |
| 22. | 4M-1832 | [2] | GASKET | |
| 23. | 1H-2629 | [2] | STRIP | |
| 24. | 8H-1141 | [4] | SHOE | |
| C | INDICATES CHANGE | |||
| Y | SEPARATE ILLUSTRATION | |||
#UEG0693S0062
4N-7905: STARTING MOTOR GP-ELECTRIC
4N7905 ELECTRIC STARTING MOTOR GROUP--Delco-Remy--24 Volt--Part 2 of 3
Part of 4N7199 Starting Motor Group shown on Page 30A
Only separate parts serviced. When complete Group is required, order 4N7903
Part of 4N7199 Starting Motor Group shown on Page 30A
Only separate parts serviced. When complete Group is required, order 4N7903
Parts for your 920 WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 4M-1849 | [1] | LEAD ASSEM. | |
| 2. | 4M-0189 | [1] | SEAL | |
| 3. | 7F-3529 | [3] | WASHER | |
| 4. | 8H-0878 | [3] | LOCKWASHER | |
| 5. | 4B-1221 | [3] | SCREW | |
| 6. | 4M-1846 | [1] | PLATE ASSEM. | |
| 7. | 7F-3525 | [8] | BUSHING | |
| 8. | 7F-4550 | [1] | PLATE | |
| 9. | 5H-6467 | [2] | SCREW | |
| 10. | 7H-2079 | [8] | LOCKWASHER | |
| 11. | 2L-6679 | [2] | PLATE | |
| 12. | 7F-4546 | [4] | HOLDER | |
| 13. | 7F-3522 | [2] | SCREW | |
| 14. | 7F-3512 | [8] | SPRING | |
| 15. | 9M-7652 | [1] | PLATE ASSEM. | |
| 16. | 7F-4549 | [2] | PLATE | |
| 17. | 4B-1311 | [2] | SCREW | |
| 18. | 7F-4545 | [1] | PLATE | |
| 19. | 3H-3697 | [2] | SCREW | |
| 20. | 2F-2860 | [6] | SCREW .312 in.(7.92 mm) long | |
| 4B-1220 | [2] | SCREW .375 in.(9.53 mm) long | ||
| 3B-4501 | [8] | LOCKWASHER | ||
| 21. | 4M-1845 | [8] | BRUSH ASSEM. | |
| 22. | 7F-3491 | [2] | WASHER | |
| 23. | 8F-9206 | [1] | SEAL | |
| 26. | 7F-3494 | [1] | WASHER | |
| 27. | 3B-4508 | [2] | LOCKWASHER | |
| 28. | 1D-5117 | [1] | NUT | |
| 29. | 1D-4719 | [1] | NUT |
#UEG0693S0063
4N-7905: STARTING MOTOR GP-ELECTRIC
4N7905 ELECTRIC STARTING MOTOR GROUP--Delco-Remy--24 Volt--Part 3 of 3
Part of 4N7199 Starting Motor Group shown on Page 30A
Only separate parts serviced. When complete Group is required, order 4N7903
Part of 4N7199 Starting Motor Group shown on Page 30A
Only separate parts serviced. When complete Group is required, order 4N7903
Parts for your 920 WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9M-7606 | [1] | PLUNGER ASSEM. | |
| 2. | 2S-4027 | [1] | WASHER | |
| 3. | 4M-1829 | [1] | BOOT | |
| 4. | 4M-1828 | [1] | RETAINER | |
| 5. | 9M-7609 | [1] | SPRING | |
| 6. | 4M-1827 | [1] | RETAINER | |
| 7. | 1H-1023 | [1] | SEAL | |
| 8. | 4S-7899 | [1] | HOUSING ASSEM. | |
| 9. | 9F-2547 | [1] | WICK | |
| 10. | 2B-4602 | [1] | PLUG | |
| 11. | 1M-9968 | [1] | BUSHING | |
| 12. | 2F-6678 | [1] | SEAL | |
| 13. | 4L-2729 | [1] | WASHER | |
| 14. | 2H-3429 | [2] | RING | |
| 15. | 4M-1853 | [1] | LEVER ASSEM. | |
| 16. | 3F-2617 | [1] | NUT | |
| 17. | 4M-1832 | [1] | GASKET | |
| 18. | 4M-1831 | [1] | PLUG | |
| 19. | 1S-0297 | [1] | HOUSING ASSEM. | |
| 20. | 4M-1896 | [1] | BUSHING | |
| 21. | 4M-1833 | [5] | SCREW 1.50 in.(38.10 mm) long | |
| 7M-0336 | [1] | SCREW .875 in.(22.23 mm) long | ||
| 22. | 2P-4708 C | [1] | DRIVE ASSEM. (800068) | |
| 23. | 9S-9771 | [1] | PINION | |
| 24. | 9S-9770 | [1] | SPRING | |
| -OR- | ||||
| 25. | 6N-3827 CH | [1] | DRIVE ASSEM. (480118) | |
| 26. | 7F-4556 | [5] | BOLT | |
| 27. | 1L-4789 | [5] | LOCKWASHER | |
| 28. | 4M-0189 | [1] | SEAL | |
| 29. | 1M-9971 | [1] | SPACER | |
| 30. | 4M-1851 | [1] | GASKET | |
| 31. | 4M-1854 | [1] | SHAFT | |
| 32. | 2D-6392 | [1] | SEAL | |
| THE FOLLOWING REPAIR KITS ARE AVAILABLE: | ||||
| 3N-3763 C | [1] | TERMINAL KIT (Insulator) | ||
| FOR 2P4708 DRIVE ASSEM.: | ||||
| 9S-9825 | [1] | KIT (cup) | ||
| 4S-9459 | [1] | KIT (washer) | ||
| C | INDICATES CHANGE | |||
| H | NOT PART OF 4N7905 MOTOR GROUP | |||
#UEG0693S0064
4N-7904: STARTING MOTOR GP-ELECTRIC
4N7904 ELECTRIC STARTING MOTOR GROUP--Prestolite--24 Volt--Part 1 of 2
Part of 4N7199 Starting Motor Group shown on Page 30A
9S7976 Solenoid parts are shown on Page 37. Only separate parts serviced
When complete Group is required, order 4N7903
Part of 4N7199 Starting Motor Group shown on Page 30A
9S7976 Solenoid parts are shown on Page 37. Only separate parts serviced
When complete Group is required, order 4N7903
Parts for your 920 WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 1D-5117 | [2] | NUT | |
| 2. | 3B-4508 | [6] | LOCKWASHER | |
| 3. | 2P-8823 | [1] | CONNECTOR | |
| 4. | 2P-8821 | [1] | LEAD ASSEM. | |
| 5. | 2P-8819 | [1] | KIT (Field Terminal Stud) | |
| (Includes Stud, Bushing & Washers) | ||||
| 6. | 1D-4719 | [4] | NUT | |
| 7. | 9S-7976 Y | [1] | SOLENOID ASSEM. | |
| (Separate Illustration) | ||||
| 8. | 6H-3622 | [4] | SCREW | |
| 3B-4504 | [4] | LOCKWASHER | ||
| 3K-6116 | [4] | WASHER | ||
| 9. | 4M-3217 | [2] | SCREW | |
| 10. | 4B-1220 | [3] | SCREW | |
| 11. | 8S-1553 | [1] | GASKET | |
| 12. | 3B-4502 | [7] | LOCKWASHER | |
| 13. | 1P-7831 | [1] | HEAD ASSEM. (Commutator End) | |
| 14. | 2B-4602 | [1] | PLUG | |
| 15. | 1P-7832 | [1] | KIT (Bearing & Wick) | |
| 16. | 2P-8820 | [1] | KIT (Commutator End Terminal Stud) | |
| (Includes Stud, Bushing & Washers) | ||||
| Y | SEPARATE ILLUSTRATION | |||
#UEG0693S0065
4N-7904: STARTING MOTOR GP-ELECTRIC
4N7904 ELECTRIC STARTING MOTOR GROUP--Prestolite--24 Volt--Part 2 of 2
Part of 4N7199 Starting Motor Group shown on Page 30A
Only separate parts serviced. When complete Group is required, order 4N7903
Part of 4N7199 Starting Motor Group shown on Page 30A
Only separate parts serviced. When complete Group is required, order 4N7903
Parts for your 920 WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 2P-8822 | [1] | PLATE ASSEM. | |
| 2. | 2P-8815 | [1] | KIT (Includes 8 Brushes) | |
| 2P-8868 | [1] | KIT (Includes 8 Springs) | ||
| 3. | 2P-8825 | [1] | SHIFT YOKE ASSEM. | |
| 4. | 2P-8817 | [1] | KIT (Yoke Adjusting) | |
| (Includes Plugs, Pin, Gasket & Nut) | ||||
| 5. | 8S-1535 | [1] | KIT (Includes 6 Plugs) | |
| 6. | 8S-2222 | [6] | KIT (Includes 10 Insulations) | |
| 7. | 8S-4684 | [1] | KIT (Bearing & Wick) | |
| 8. | 8S-1543 | [1] | HOUSING ASSEM. (Pinion) | |
| 9. | 2B-4602 | [1] | PLUG | |
| 10. | 8S-4680 | [1] | KIT (Includes 10 Seals) | |
| 11. | 4N-4517 | [1] | DRIVE ASSEM. | |
| 12. | 2H-3931 | [1] | SEAL | |
| 13. | 2P-8824 | [1] | HOUSING ASSEM. | |
| 2B-4602 | [1] | PLUG | ||
| 14. | 8S-2226 | [1] | BUSHING | |
| 15. | 8S-2225 | [1] | SEAL | |
| 16. | 0L-1340 | [7] | SCREW | |
| 2P-8816 | [1] | KIT (Includes Housing Screws) | ||
| 17. | 3B-4504 | [7] | LOCKWASHER | |
| 18. | 4M-0189 | [1] | SEAL | |
| 19. | 2P-8818 | [1] | KIT (Field Coil) | |
| (Includes Coils, Gaskets & Screws) | ||||
| 20. | 8S-1546 | [1] | ARMATURE ASSEM. | |
| 8S-8075 | [1] | KIT (Armature Thrust Washers) | ||
#UEG0693S0066
4N-7752: STARTING MOTOR GP-ELECTRIC
4N7752 ELECTRIC STARTING MOTOR GROUP--Prestolite--Part 1 of 2
Part of 7S3622 Starting Motor Group shown on Page 30A
9S7976 Solenoid parts are shown on Page 37
Only separate parts serviced. When complete Group is required, order 4N3181
Part of 7S3622 Starting Motor Group shown on Page 30A
9S7976 Solenoid parts are shown on Page 37
Only separate parts serviced. When complete Group is required, order 4N3181
Parts for your 920 WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 1D-5117 | [2] | NUT (jam) | |
| 2. | 3B-4508 | [6] | LOCKWASHER | |
| 3. | 4N-9405 | [1] | CONNECTOR | |
| 4. | 4N-9404 | [1] | LEAD ASSEM. | |
| 5. | 2P-8819 | [1] | KIT (Field Terminal Stud) | |
| (Includes Stud, Bushing and Washers) | ||||
| 6. | 1D-4719 | [4] | NUT | |
| 7. | 9S-7976 Y | [1] | SOLENOID ASSEM. | |
| (Separate Illustration) | ||||
| 8. | 6H-3622 | [4] | SCREW | |
| 3B-4504 | [4] | LOCKWASHER | ||
| 3K-6116 | [4] | WASHER | ||
| 9. | 4M-3217 | [2] | SCREW | |
| 10. | 4B-1220 | [3] | SCREW | |
| 11. | 085-1553 | [1] | GASKET | |
| 12. | 3B-4502 | [7] | LOCKWASHER | |
| 13. | 1P-7831 | [1] | HEAD ASSEM. (Commutator End) | |
| 14. | 2B-4602 | [1] | PLUG | |
| 15. | 1P-7832 | [1] | KIT (Bearing and Wick) | |
| 16. | 4N-9403 | [1] | KIT (Commutator End Terminal Stud) | |
| (Includes Stud, Bushing and Washers) | ||||
| Y | SEPARATE ILLUSTRATION | |||
#UEG0693S0067
4N-7752: STARTING MOTOR GP-ELECTRIC
4N7752 ELECTRIC STARTING MOTOR GROUP--Prestolite--Part 2 of 2
Part of 7S3622 Starting Motor Group shown on Page 30A
Only separate parts serviced. When complete Group is required, order 4N3181
Part of 7S3622 Starting Motor Group shown on Page 30A
Only separate parts serviced. When complete Group is required, order 4N3181
Parts for your 920 WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 2P-8822 | [1] | PLATE ASSEM. | |
| 2. | 4N-9401 | [1] | KIT (Includes 6 Brushes) | |
| 2P-8868 | [1] | KIT (Includes 8 Springs) | ||
| 3. | 2P-8825 | [1] | SHIFT YOKE ASSEM. | |
| 4. | 2P-8817 | [1] | KIT (Yoke Adjusting) | |
| (Includes Plugs, Pin, Gasket & Nut) | ||||
| 5. | 8S-1535 | [1] | KIT (Includes 6 Plugs) | |
| 6. | 4N-9402 | [1] | KIT (Includes 10 Insulations) | |
| 7. | 8S-4684 | [1] | KIT (Bearing & Wick) | |
| 8. | 8S-1543 | [1] | HOUSING ASSEM. (Pinion) | |
| 9. | 2B-4602 | [1] | PLUG | |
| 10. | 8S-4680 | [1] | KIT (Includes 10 Seals) | |
| 11. | 4N-4517 | [1] | DRIVE ASSEM. | |
| 12. | 2H-3931 | [1] | SEAL | |
| 13. | 2P-8824 | [1] | HOUSING ASSEM. | |
| 2B-4602 | [1] | PLUG | ||
| 14. | 8S-2226 | [1] | BUSHING | |
| 15. | 8S-2225 | [1] | SEAL | |
| 16. | 0L-1340 | [7] | SCREW | |
| 2P-8816 | [1] | KIT (Includes Housing Screws) | ||
| 17. | 3B-4504 | [7] | LOCKWASHER | |
| 18. | 4M-0189 | [1] | SEAL | |
| 19. | 2P-8818 | [1] | KIT (Field Coil) | |
| (Includes Coils, Gaskets & Screws) | ||||
| 20. | 8S-1546 | [1] | ARMATURE ASSEM. | |
| 8S-8075 | [1] | KIT (Armature Thrust Washers) | ||
#UEG0693S0068
9S-7976: SOLENOID AS
9S7976 SOLENOID ASSEMBLY--24 Volt
Part of 2P6162, 4N7904 and 4N7752 Electric Starting Motor Groups
shown on Pages 32, 36D and 36F
Part of 2P6162, 4N7904 and 4N7752 Electric Starting Motor Groups
shown on Pages 32, 36D and 36F
Parts for your 920 WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 9M-7657 C | [4] | NUT-SEALING | |
| 2. | 8S-8023 | [1] | COVER AS | |
| 3. | 8S-8024 | [1] | GASKET-COVER | |
| 4. | 9B-7235 | [1] | SCREW-MACHINE | |
| 9B-7233 | [1] | LOCKWASHER | ||
| 5. | 8S-1528 | [1] | BOOT | |
| 6. | 8S-8021 | [1] | CORE AS | |
| THE FOLLOWING REPAIR | ||||
| KITS ARE AVAILABLE: | ||||
| 8S-1524 | [1] | KIT-TERMINAL STUD (BATTERY) | ||
| 8S-1525 | [1] | KIT-TERMINAL STUD (MOTOR) | ||
| 9S-8688 | [1] | KIT-CONTACT END CORE | ||
| 8S-1527 | [1] | KIT-YOKE END CORE | ||
| C | CHANGE FROM PREVIOUS TYPE | |||
#UEG0693S0069
6N-5123: SWITCH AS-SOLENOID
6N5123 SOLENOID SWITCH ASSEMBLY--24 Volt
Part of 4N3182 and 4N7905 Starting Motor Groups shown on Pages 34 and 36A
Part of 4N3182 and 4N7905 Starting Motor Groups shown on Pages 34 and 36A
Parts for your 920 WHEEL LOADER:
CATERPILLAR SIS| Pos. | Part No | Qty | Parts name | Comments |
|---|---|---|---|---|
| 1. | 7N-0908 C | [ 1] | TERMINAL ASSEM. | |
| (Includes) | ||||
| 4M-1834 | [ 1] | PLATE | ||
| 2. | 7F-4907 | [ 1] | STRIP | |
| 3. | 3H-3681 | [ 2] | NUT | |
| 4. | 3B-4508 | [ 4] | LOCKWASHER | |
| 5. | 3H-3680 | [ 2] | NUT | |
| 6. | 7F-3494 | [ 2] | WASHER | |
| 7. | 4M-1836 | [ 2] | INSULATOR | |
| 8. | 4M-1837 | [ 2] | BUSHING | |
| 9. | 7F-4906 C | [ 1] | STUD | |
| 10. | 7N-0909 | [ 1] | TERMINAL ASSEM. | |
| 11. | 9S-4490 | [ 1] | GASKET | |
| 12. | 4M-5274 | [ 1] | SCREW | |
| 13. | 9S-4489 | [ 4] | SCREW ASSEM. | |
| 14. | 4M-3217 | [ 2] | SCREW | |
| 15. | 4M-1814 | [ 1] | CONTACT ASSEM. | |
| 16. | 3P-0072 | [ 1] | CASE ASSEM. | |
| 17. | 1F-0073 | [ 2] | CLIP | |
| 18. | 4M-1815 | [ 1] | SPRING | |
| INDICATES CHANGE | ||||
Information:
ELECTRICAL AND STARTING SYSTEM
STARTING MOTOR GP
General Service Information
Engine News
Special Instruction
Installation of New Shift Lever Assembly for All Starter Motors {1453}
Installation of New Shift Lever Assembly for All Starter Motors {1453}
Installation of New Shift Lever Assembly for All Starter Motors {1453}
Procedure to Install the Insulator on to Series Starters on All Engines {1453}
Procedure to Install the Insulator on to Series Starters on All Engines {1453}
Procedure to Install the Insulator on to Series Starters on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453}
Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Replace Armature of Starter Motor On All Cat<SUP>®</SUP> Products {1408, 1450, 1453}
Procedure to Replace Armature of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Armature of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat<SUP>®</SUP> Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Drive Assembly of Starter Motor On All Cat<SUP>®</SUP> Products {1453}
Procedure to Replace Drive Assembly of Starter Motor On All Cat® Products {1453}
Procedure to Replace Drive Assembly of Starter Motor On All Cat® Products {1453}
Specifications
Systems Operation
Testing and Adjusting
Troubleshooting
Engine Does Not Crank with Starting Motor On and Pinion Engaging Ring Gear
37-MT, 41-MT, and 42-MT Series Starting Motors
37-MT, 41-MT, and 42-MT Series Starting Motors
Disassembly and Assembly
Service Magazine
Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16
1987/03/16
New PRELUB Systems Available For Medium To Large Caterpillar Construction Equipment {1319}
1992/04/06
1992/04/06



