3208 INDUSTRIAL ENGINE 90N00001-06120 ELECTRICAL AND STARTING SYSTEM Caterpillar SIS

ETR Junction Box-Switchgear Not Required (OP,WT,OS)
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

ETR Junction Box-Switchgear Not Required (OP,WT)
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

ETR Introduction
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Service Letter-APD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Testing and Adjusting

Testing And Adjusting
DELCO REMY 20-SI SERIES ALTERNATOR

General Testing and Adjusting Information
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Disassembly and Assembly

Alternator
DELCO REMY 20-SI SERIES ALTERNATOR

Service Magazine

Troubleshooting Water In Shut-Off Solenoid Housing{1259}
1981/06/08

New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23

Bent Lever For Fuel Shut-Off Solenoid Can Cause Low Engine Performance{1286,1259}
1982/02/01

New Gasket Used In Governor And Fuel Injection Pump Group{1259,1286}
1982/03/01

Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28

New Seal Used On Governor Control Shaft{1264,1265}
1982/11/22

New Shutoff Solenoid Group Used{1259}
1983/03/21

Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27

Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01

Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07

Maintenance Free Batteries{1401}
1986/03/10

New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10

Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control{1400,1401,4450}
1986/03/24

Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07

Three Element Speed Switch Replaces Dual Element Speed Switch{7418,7411,7410,7421}
1986/04/21

Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01

Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10

Check For Dirt Before Replacing Pyrometer Switch{1050,7466}
1986/12/15

Improved Shut-Off Solenoids For Engines Equipped With Sleeve Metering Fuel Systems{1259}
1977/03/07

Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08

Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Identification Of External Terminals On Alternators{1405,1406,1400}
1987/03/23

Use Improved Heat Start Switch{1416}
1987/04/20

Products Equipped With Diagnostic Connectors Require Less Time For Electrical Troubleshooting{1400}
1987/05/04

Alternator "R" Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04

Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04

Testing The Starter On The Engine{1401,1450}
1987/05/04

Check Alternator Output Connection Prior To Machine Delivery{1405}
1987/05/18

Improved Start Switch Used{1416}
1987/05/25

Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25

Correct Torque Value For Alternator Drive Pulley Retaining Nut Is Important{1405}
1987/11/23

9G7641 Start Switch Is Improved{1416,1400}
1988/05/16

Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20

Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12

Ether Starting Aid System Improves Cold Weather Starts{1456}
1979/03/19

New 35-Ampere Alternator Used On Some Engines In Caterpillar Equipment{1405,1406}
1979/08/13

Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24

Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05

Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26

General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17

High Performance Maintenance Free Battery Available{1401}
1989/01/16

Limitations On Engine Cranking Time{1453,1401}
1989/03/27

How To Troubleshoot A Short-To-Ground In Power Wiring{1400}
1989/03/27

Preventive Maintenance For Batteries{1401}
1989/03/27

Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24

Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01

Special Instruction, "Battery Charging Rate And Time Tables," Available On Oil Resistant Paper{0374,1401}
1989/06/19

Improved 9W1077 Start Switch Assembly And 7N4160 Heat Start Switch Group{1416}
1990/12/10

New 100 Amp Alternators Available For Applications With Large Electrical Requirements{1405}
1992/02/17

New Spring Used In Governor Control Groups{1265}
1992/04/20

Catalytic Converter And Exhaust Conditioning Products Available{1091}
1995/01/16

MOTOR GP

Special Instruction

Installation of Electric Starting Motors{1453}
Installation of Electric Starting Motors{1453}

Service Magazine

Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28

PANEL GP-CIRCUIT BREAKER

Special Instruction

Circuit Breaker Harness Assembly {1420}
Circuit Breaker Harness Assembly {1420}

PANEL GP-FUSE

REGULATOR GP-VOLTAGE

Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}
Upgrading Alternators To Include An Integrated Circuit Regulator{1405, 1410}

Service Magazine

New Regulator And Field Coil Assemblies Used{1410,1405}
1981/11/23

Voltage Regulator Cross Reference Chart{1410,1405}
1985/07/01

Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22

SENDER GP

Special Instruction

Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}

Service Magazine

New "Two Inch" Gauges, Indicator And Senders Available{7450}
1986/06/02

SENSOR GP

Special Instruction

Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}

Procedure to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562}
Procedure to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562}

Procedure to Install an Aftertreatment (Mechanical) Kit on All Caterpillar® Diesel Engines {108D, 108U, 1408, 1907, 1921, 1923, 7553}
Procedure to Install an Aftertreatment (Mechanical) Kit on All Caterpillar^® Diesel Engines {108D, 108U, 1408, 1907, 1921, 1923, 7553}

Specifications

Magnetic Pickup
3208 INDUSTRIAL AND MARINE ENGINE ATTACHMENTS

Tool Operating Manual

Using the 265-4177, 265-4209 Service Tool Groups to Install Sensors in Position-Sensing Hydraulic Cylinders{0599, 0709, 0738, 1439, 7562, 7562}
Using the 265-4177, 265-4209 Service Tool Groups to Install Sensors in Position-Sensing Hydraulic Cylinders{0599, 0709, 0738, 1439, 7562, 7562}

Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}
Using the 453-3204 Pressure and Temperature Test Group{0374, 0599, 0706, 0708, 0709, 0731, 0732, 0738, 1408, 1439}

Testing and Adjusting

Magnetic Pickup Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Service Magazine

New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10

New "Two Inch" Gauges, Indicator And Senders Available{7450}
1986/06/02

Ether Starting Aid System Improves Cold Weather Starts{1456}
1979/03/19

Procedure Now Available to Test the Position Sensor of a Hydraulic Cylinder {1439, 7562}
2012/10/04

SHUTOFF GP

Engine News

Rack Shut-Off Solenoid Can Be Removed And Engine Started When There Is An Emergency
1980/11/12

Troubleshooting Water In Shut-Off Solenoid Housing
1981/07/01

Bent Lever For Fuel Shut-Off Solenoid Can Cause Low Engine Performance
1982/02/10

New Shutoff Solenoid Group Used
1983/04/27

Improved Shut-Off Solenoids For Engines Equipped With Sleeve Metering Fuel Systems
1977/02/28

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13

Special Instruction

Use Of FT1525 Alignment Pin, FT1526 Salvage Fixture And FT1698 Bearing Installation Tool For Reconditioning Of 3208 Governor Housings{1265, 1264}
Use Of FT1525 Alignment Pin, FT1526 Salvage Fixture And FT1698 Bearing Installation Tool For Reconditioning Of 3208 Governor Housings{1265, 1264}

Specifications

Shutoff Solenoids
3208 INDUSTRIAL & MARINE ENGINES

Disassembly and Assembly

Shutoff Housing
3208 INDUSTRIAL & MARINE ENGINES

Service Magazine

Troubleshooting Water In Shut-Off Solenoid Housing{1259}
1981/06/08

Bent Lever For Fuel Shut-Off Solenoid Can Cause Low Engine Performance{1286,1259}
1982/02/01

New Gasket Used In Governor And Fuel Injection Pump Group{1259,1286}
1982/03/01

New Seal Used On Governor Control Shaft{1264,1265}
1982/11/22

New Shutoff Solenoid Group Used{1259}
1983/03/21

Three Element Speed Switch Replaces Dual Element Speed Switch{7418,7411,7410,7421}
1986/04/21

Improved Shut-Off Solenoids For Engines Equipped With Sleeve Metering Fuel Systems{1259}
1977/03/07

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08

New Spring Used In Governor Control Groups{1265}
1992/04/20

Improved Starter Solenoid Assemblies Available {1467,1518}
1996/09/02

SOLENOID GP

Engine News

Rack Shut-Off Solenoid Can Be Removed And Engine Started When There Is An Emergency
1980/11/12

Troubleshooting Water In Shut-Off Solenoid Housing
1981/07/01

Bent Lever For Fuel Shut-Off Solenoid Can Cause Low Engine Performance
1982/02/10

New Shutoff Solenoid Group Used
1983/04/27

12-Volt Starter Solenoid Available For 7T2265 And 7T2266 Starting Motors
1987/02/01

Improved Starter Solenoid Prevents Contact Corrosion
1987/12/01

Adjust Bosch Solenoid If Replaced Or Reinstalled
1988/01/01

Magnetic Switches (Starter Relays) Improved
1988/03/01

Improved Shut-Off Solenoids For Engines Equipped With Sleeve Metering Fuel Systems
1977/02/28

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13

Specifications

Shutoff Solenoids
3208 INDUSTRIAL & MARINE ENGINES

Disassembly and Assembly

Shutoff Housing
3208 INDUSTRIAL & MARINE ENGINES

Service Magazine

Troubleshooting Water In Shut-Off Solenoid Housing{1259}
1981/06/08

Bent Lever For Fuel Shut-Off Solenoid Can Cause Low Engine Performance{1286,1259}
1982/02/01

New Gasket Used In Governor And Fuel Injection Pump Group{1259,1286}
1982/03/01

New Shutoff Solenoid Group Used{1259}
1983/03/21

Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10

Improved Shut-Off Solenoids For Engines Equipped With Sleeve Metering Fuel Systems{1259}
1977/03/07

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08

12-Volt Starter Solenoid Available For 7T2265 And 7T2266 Starting Motors{1407}
1987/02/16

Improved Starter Solenoid Prevents Contact Corrosion {1453}
1987/11/30

Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14

Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24

Improved Starter Solenoid Assemblies Available {1467,1518}
1996/09/02

SOLENOID GP-SHUTOFF

Disassembly and Assembly

Shutoff Housing
3208 INDUSTRIAL & MARINE ENGINES

Service Magazine

Troubleshooting Water In Shut-Off Solenoid Housing{1259}
1981/06/08

New Gasket Used In Governor And Fuel Injection Pump Group{1259,1286}
1982/03/01

New Shutoff Solenoid Group Used{1259}
1983/03/21

Improved Shut-Off Solenoids For Engines Equipped With Sleeve Metering Fuel Systems{1259}
1977/03/07

Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures{1259}
1977/08/08

STARTING AID GP

Engine News

Cetane Injection Group Uses New Orifice, Tee and Seals
1984/10/24

Determining The Cause Of Glow Plug Tip Failures
1986/06/01

Special Instruction

INSTALLATION, OPERATION AND MAINTENANCE OF 9N3771 INJECTION GROUP (CETANE){1250}
INSTALLATION, OPERATION AND MAINTENANCE OF 9N3771 INJECTION GROUP (CETANE){1250}

Service Magazine

Cetane Injection Group Uses New Orifice, Tee and Seals{1250,1274}
1984/10/29

Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02

Ether Starting Aid System Improves Cold Weather Starts{1456}
1979/03/19

General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17

A New Ether Cylinder O-ring is Now Used on All Caterpillar Products {1456}
2013/09/24

STARTING AR

Special Instruction

Installation of Electric Starting Motors{1453}
Installation of Electric Starting Motors{1453}

Service Magazine

Engine Shuts Down Immediately After Start-Up {7400}
1985/10/21

Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16

Testing The Starter On The Engine{1401,1450}
1987/05/04

Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14

Ether Starting Aid System Improves Cold Weather Starts{1456}
1979/03/19

Cranking Speeds Necessary To Start Diesel Engines{0374,1000,1450}
1979/09/24

STARTING MOTOR GP

General Service Information

Introduction
DELCO REMY CRANKING MOTORS 30-MT, 35-MT, 40-MT, 50-MT SERIES

Delco Remy
DELCO REMY CRANKING MOTORS 30-MT, 35-MT, 40-MT, 50-MT SERIES

Engine News

12-Volt Starter Solenoid Available For 7T2265 And 7T2266 Starting Motors
1987/02/01

Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts
1987/03/01

Testing The Starter On The Engine
1987/05/01

Remanufactured Heavy-Duty Starters And High-Amp Alternators
1987/06/01

Improved Starter Solenoid Prevents Contact Corrosion
1987/12/01

Be Sure Battery Cable To Starter Connection Has Correct Torque
1988/03/01

Magnetic Switches (Starter Relays) Improved
1988/03/01

New Flywheel Ring Gear Available To Improve Starter Engagement
1990/04/01

New Starting Motors Used {1453}
2002/05/01

Caterpillar Remanufactured Electric Starting Motors Are Improved {1453}
2011/05/16

Special Instruction

Installation of Electric Starting Motors{1453}
Installation of Electric Starting Motors{1453}

Caterpillar PRELUB® Diagnostics{1469}
Caterpillar PRELUB^® Diagnostics{1469}

Installation of New Shift Lever Assembly for All Starter Motors {1453}
Installation of New Shift Lever Assembly for All Starter Motors {1453}

Procedure to Install the Insulator on to Series Starters on All Engines {1453}
Procedure to Install the Insulator on to Series Starters on All Engines {1453}

Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}
Installation of Repair Kit-Solenoid Plunger Assembly on All Engines {1453}

Procedure to Install Terminal Kit on All Engines {1453}
Procedure to Install Terminal Kit on All Engines {1453}

Procedure to Install Brush Holder Assembly in All Engines {1453}
Procedure to Install Brush Holder Assembly in All Engines {1453}

Procedure to Replace Armature of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Armature of Starter Motor On All Cat^® Products {1408, 1450, 1453}

Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Commutator End (CE) Housing of Starter Motor On All Cat^® Products {1408, 1450, 1453}

Procedure to Replace Drive Assembly of Starter Motor On All Cat® Products {1453}
Procedure to Replace Drive Assembly of Starter Motor On All Cat^® Products {1453}

Specifications

Electric Starter Motor
3208 INDUSTRIAL & MARINE ENGINES

Starter Magnetic Switch
3208 INDUSTRIAL AND MARINE ENGINE ATTACHMENTS

Starting Motor
Starting Motor - Delco 50-MT

Systems Operation

Component Description
Starting Motor - Delco 50-MT

General Information
Starting Motor - Delco 50-MT

Normal Operation
Starting Motor - Delco 50-MT

Testing and Adjusting

Starting Motor Solenoid - Test
Starting Motor - Delco 50-MT

Field Winding - Test
Starting Motor - Delco 50-MT

Armature - Test
Starting Motor - Delco 50-MT

Brush and Brush Holder - Check
Starting Motor - Delco 50-MT

Pinion Drive - Check
Starting Motor - Delco 50-MT

No Load - Test
Starting Motor - Delco 50-MT

Pinion Clearance - Adjust
Starting Motor - Delco 50-MT

Troubleshooting

General Information
Starting Motor - Delco 50-MT

Pinion Does Not Engage Ring Gear
Starting Motor - Delco 50-MT

Engine Does Not Crank with Starting Motor On and Pinion Engaging Ring Gear
Starting Motor - Delco 50-MT

Starting Motor Continues to Operate after Start Switch Has Been Released
Starting Motor - Delco 50-MT

Pinion Continues to Engage after Engine Starts
Starting Motor - Delco 50-MT

Starting Motor Does Not Turn or Turns Slowly
Starting Motor - Delco 50-MT

Disassembly and Assembly

General Information
Starting Motor - Delco 50-MT

Starting Motor - Disassemble
Starting Motor - Delco 50-MT

Starting Motor - Assemble
Starting Motor - Delco 50-MT

Service Magazine

Replacement Of Brush Holder Pins In Delco-Remy Electric Starting Motors{1453}
1982/06/28

New Start Switch Used {1416,1453}
1986/07/07

Adjust Bosch Solenoid If Replaced Or Reinstalled{1407,1453}
1986/11/10

12-Volt Starter Solenoid Available For 7T2265 And 7T2266 Starting Motors{1407}
1987/02/16

Modification To Prevent Starter From Remaining Engaged With Flywheel After Engine Starts{1400,1450}
1987/03/16

Testing The Starter On The Engine{1401,1450}
1987/05/04

Remanufactured Heavy-Duty Starters And High-Amp Alternators{1405,1453}
1987/05/25

Improved Starter Solenoid Prevents Contact Corrosion {1453}
1987/11/30

Be Sure Battery Cable-To-Starter Connection Has Correct Torque{1453}
1988/03/14

Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14

Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05

Limitations On Engine Cranking Time{1453,1401}
1989/03/27

Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24

New Flywheel Ring Gear Available To Improve Starter Engagement{1158,1454}
1990/04/02

New PRELUB Systems Available For Medium To Large Caterpillar Construction Equipment {1319}
1992/04/06

0R5207 Remanufactured Starter May Not Fit In Some Applications{1453}
1993/11/29

Improved Starter Solenoid Assemblies Available {1467,1518}
1996/09/02

Examine Failed Starting Motors to Understand the Reason for Failure {1453}
2002/10/28

SWITCH GP

Engine News

Three Element Speed Switch Replaces Dual Element Speed Switch
1986/05/01

New Start Switch Used
1986/07/01

Check For Dirt Before Replacing Pyrometer Switch
1987/01/01

Magnetic Switches (Starter Relays) Improved
1988/03/01

Improved 9W1077 Start Switch Assembly And 7N4160 Heat Start Switch Group
1990/12/01

Special Instruction

Installation of 7W2743 Speed Switch Assembly{7427}
Installation of 7W2743 Speed Switch Assembly{7427}

Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}

Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}

Service Letter-NACD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Brazil

Service Letter-Truck/Ag/Marine

Specifications

Water Temperature Switches
3208 INDUSTRIAL AND MARINE ENGINE ATTACHMENTS

Pressure Switches
3208 INDUSTRIAL AND MARINE ENGINE ATTACHMENTS

Starter Magnetic Switch
3208 INDUSTRIAL AND MARINE ENGINE ATTACHMENTS

Service Letter-China

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Asia

Service Letter-APD

Testing and Adjusting

Overspeed Verification Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Overspeed Calibration
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Crank Terminate Speed Calibration
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Oil Step Speed Calibration
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Diode Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Engine Oil Pressure Switch Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Water Temperature Contactor Switch Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Service Magazine

Maintenance Free Batteries{1401}
1986/03/10

New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10

Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07

Three Element Speed Switch Replaces Dual Element Speed Switch{7418,7411,7410,7421}
1986/04/21

New Start Switch Used {1416,1453}
1986/07/07

Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01

Check For Dirt Before Replacing Pyrometer Switch{1050,7466}
1986/12/15

Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Use Improved Heat Start Switch{1416}
1987/04/20

Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04

Testing The Starter On The Engine{1401,1450}
1987/05/04

Improved Start Switch Used{1416}
1987/05/25

Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14

9G7641 Start Switch Is Improved{1416,1400}
1988/05/16

Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20

Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12

Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22

Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05

Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26

High Performance Maintenance Free Battery Available{1401}
1989/01/16

Limitations On Engine Cranking Time{1453,1401}
1989/03/27

Preventive Maintenance For Batteries{1401}
1989/03/27

Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24

Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01

Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01

Special Instruction, "Battery Charging Rate And Time Tables," Available On Oil Resistant Paper{0374,1401}
1989/06/19

Improved 9W1077 Start Switch Assembly And 7N4160 Heat Start Switch Group{1416}
1990/12/10

Wiring Harness Conduit Component Sizes {1408}
1995/02/13

Improved Prelube Pressure Switch Available {1400,1435,1319}
1995/09/11

An Improved 5P-8500 Key Is Now Available {1416, 1416, 7000, 7000}
2011/12/01

TOOLS

Truck Engine News

Coolant/Battery Tester Group Quickly Tests Coolant and Battery Acid {0773, 0785}
2005/01/17

Do Not Use the 261-3363 Wireless Communication Adapter with Model Year 2007 Cat Engines and Transmissions in On-Highway Trucks {0785, 1930, 7620}
2007/10/01

Engine News

New Address For Repair Of Diagnostic Tools
1982/06/16

Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25

5P957 And 5P3514 Coolant And Battery Tester
1987/04/01

Two New Self-Powered Digital Tachometers And Signal Generator Available
1987/05/01

Caterpillar Electronic Technician (Cat ET) 2001B-Service Pack 1 Software Upgrade is Now Available {0785}
2002/02/01

2002A Service Pack 1 for Caterpillar Electronic Technician (Cat ET) is now available {0785}
2002/08/01

The 237-5130 Digital Multimeter Gp Features a Built-in Infrared Thermometer {0785}
2004/04/19

Coolant/Battery Tester Group Quickly Tests Coolant and Battery Acid {0773, 0785}
2005/01/17

260-5800 Electrical Test Group Packages Digital Multimeter, Clamp-on Ammeter, Current Detector, and Test Leads in Convenient Carrying Case {0785}
2005/03/07

270-5051 Repair Kit (Electrical Connectors) Available for Repairs to Wiring Harnesses with Ampseal 16 and A4E 2 Connectors {0709, 1408}
2006/03/20

Enhanced Voltmeter Leads Are Now Available {0785}
2006/02/13

Test Cable Group Checks Three-Wire, Active Analog Circuits That Are Used in Sensors {0779, 0785}
2006/10/16

277-4734 Bypass Harness Assembly Allows Cat Electronic Technician (Cat ET) to Communicate with ADEM IV:E2 Electronic Control Modules {0779, 0785, 1901, 1930}
2006/09/01

Special Instruction

Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}

Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}
Use of 8T5200 Signal Generator/Counter Group{0778, 0783, 0785}

Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}

An Aid To Reading Multimeter Scales{0785}
An Aid To Reading Multimeter Scales{0785}

Tool Operating Manual

348-5430 Multi-Tool Gp 2 {0709, 0769, 0785}
348-5430 Multi-Tool Gp 2 {0709, 0769, 0785}

NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}
NEHS1032: 538-5051 Communications Adapter 3 {0599, 0709, 1900, 4800, 7490, 7600}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}

Using the Communications Adapter 3{1900}
Using the Communications Adapter 3{1900}

Using the 8T-2700 Blowby/Air Flow Indicator{0781, 0785, 1317}
Using the 8T-2700 Blowby/Air Flow Indicator{0781, 0785, 1317}

146-4080 Digital Multimeter Specification, Testing, and Maintenance Manual{0374, 0599, 0709}
146-4080 Digital Multimeter Specification, Testing, and Maintenance Manual{0374, 0599, 0709}

Communication Adapter II{0600, 0709, 7600, 7610}
Communication Adapter II{0600, 0709, 7600, 7610}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{0374, 0599, 0701, 0709}

131-5051 Dataview Group and Dataview Portable Tech Station Group{0374, 0599, 0701, 0709}
131-5051 Dataview Group and Dataview Portable Tech Station Group{0374, 0599, 0701, 0709}

Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}
Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}

NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}
NEHS1270 TesLite and LoadProCables {0374, 0599, 0709, 0734}

Reuse And Salvage Guidelines

Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}

Troubleshooting

Service Tools
Starting Motor - Delco 50-MT

Service Magazine

New Address For Repair Of Diagnostic Tools{0650}
1982/06/14

6V6124 Calibration Coil Available To Calibrate And Check 6V4910 AC/DC Clamp-On Ammeter{0651}
1982/06/28

Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16

Use Caterpillar 6V50 Engine Timing Indicator For Accurate Readings{0782,0785,0775}
1985/05/27

Two, New Top Dead Center Magnetic Transducers Available{0651,0653,1214,1250}
1985/10/07

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Two New Self-Powered Digital Tachometers And Signal Generator Available {7462}
1987/05/11

New 1U5524 Adapter Cable Available For Use With 6V9060 Spark Timing Adapter Group And 8T5300 Engine Timing Indicator Group{0779,0781}
1987/07/06

Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12

Diagnostic Cables and Harnesses Are Available {0785}
2000/12/25

Caterpillar Electronic Technician (Cat ET) 2001B-Service Pack 1 Software Upgrade is Now Available {0785}
2002/02/11

New Service Information Tool for CAT Dealers is Now Available {1900}
2002/06/17

2002A Service Pack 1 for Caterpillar Electronic Technician (Cat ET) is Now Available {0785}
2002/08/19

Coolant/Battery Tester Group Quickly Tests Coolant and Battery Acid {0773, 0785}
2005/01/17

260-5800 Electrical Test Group Packages Digital Multimeter, Clamp-on Ammeter, Current Detector, and Test Leads in Convenient Carrying Case {0785}
2005/03/07

The 285-0910 Multi-Tool Gp Incorporates Four Diagnostic Tools into a Single, Hand Held Unit {0774, 0779, 0781, 0782}
2006/12/01

New 271-8590 Analyzer Gp (24-Volt) Quickly Identifies Starting and Charging System Problems {0709, 1406}
2006/09/25

277-2362 Transmission Analyzer III Group Offers Upgraded Diagnostic Capabilities {0769, 0779, 0783}
2007/10/22

Updated Instruction For The Bypass Harness {0785, 1408}
2008/03/17

New Firmware Is Now Available for Communications Adapter 3 {7610, 7620}
2011/10/20

New Software For Cat® ET Can Now Be Used For All Caterpillar Products {0785, 7606}
2013/08/15

A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785}
A New Communication Adapter Cable As Is Now Available For Certain Cat Products {0785}

VALVE GP

Special Instruction

Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}
Creating Fuel Pump, and Fuel Nozzle Reference Parts for Checking Fuel Pump Test Stands and Nozzle Pop Testers{1254}

Service Magazine

New Coolant Temperature Regulator Housing And Vent Line Valve Give Better Control Of Engine Cooling; Conversion Kits Available{1380,1355}
1979/10/22

Compression Ratio Increased On Remanufactured OR1094 & OR1095 Engines To Reduce Amount Of White Smoke On Cold Weather Start-Ups{1000,1254,1290}
1991/09/30

Date Code On 7000 Series Fuel Injection Nozzles; New Seals Used In 7000 Series Fuel Injection Nozzles{1254}
1994/05/23

WARNING GP

Special Instruction

Installation of 244-1090 Alarm Gp {7400, 7402, 7407}
Installation of 244-1090 Alarm Gp {7400, 7402, 7407}

Installation of the White Noise Back Up Alarms {7406}
Installation of the White Noise Back Up Alarms {7406}

Service Magazine

Wiring Harness Conduit Component Sizes {1408}
1995/02/13

WIRING GP

Engine News

FT1808 Cable Permits Easier Use Of 6V2100 Multitach To Check Engine Or Alternator RPM
1984/01/18

Be Sure Battery Cable To Starter Connection Has Correct Torque
1988/03/01

Wiring Harness Conduit Component Sizes {1408}
1995/02/01

Correction to The Pocket Guide, SEBD0402 Is Available as a Reference for Routing and Installing Wire Harness Assemblies {1408}
2000/07/01

270-5051 Repair Kit (Electrical Connectors) Available for Repairs to Wiring Harnesses with Ampseal 16 and A4E 2 Connectors {0709, 1408}
2006/03/20

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2010/05/13

Special Instruction

Installation of 7W2743 Speed Switch Assembly{7427}
Installation of 7W2743 Speed Switch Assembly{7427}

Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}
Use of the 4C6534 Speed Switch Calibration Harness{0781, 0785}

INSTALLING THE 1041820 WIRING KIT{7417}
INSTALLING THE 1041820 WIRING KIT{7417}

Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}
Retrofit Installation of Coolant Loss Sensor{1353, 1395, 7422, 7470}

Wiring Diagram-Grounded System{1400}
Wiring Diagram-Grounded System{1400}

Battery Ratings And Cross Reference Chart{1401}
Battery Ratings And Cross Reference Chart{1401}

Cross-Reference for Electrical Connectors {7553}
Cross-Reference for Electrical Connectors {7553}

Circuit Breaker Harness Assembly {1420}
Circuit Breaker Harness Assembly {1420}

Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}
Service Of Machined Terminals And Service of Stamped and Formed Terminals{7553}

Guidelines for Routing and Installing Wire Harness Assemblies {1408, 7553}
Guidelines for Routing and Installing Wire Harness Assemblies {1408, 7553}

Repair Procedure for Damaged Harness Wiring {1408}
Repair Procedure for Damaged Harness Wiring {1408}

Installation of the White Noise Back Up Alarms {7406}
Installation of the White Noise Back Up Alarms {7406}

Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}
Procedure to Properly Tighten the Nuts on the Solenoid Studs on Electronic Unit Injectors (EUI){1290, 1408, 1900}

Service Letter-NACD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Australia

Service Letter-CFEL

Service Letter-CSARL

Service Letter-Americas

Service Letter-Brazil

Service Letter-Truck/Ag/Marine

Technical Information Bulletin

Testing The Function Of The 3E6477 Relay Assembly (24 Volt)
Testing The Function Of The 3E6477 Relay Assembly (24 Volt)

Tool Operating Manual

Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}
Using the 362-3555 Connector Repair Kit to Service Harnesses with Ampseal 16 Connectors{0685, 1408}

Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}
Using the U5MK1110 Ampseal Connector Kit for Wiring Harness Repairs on Perkins Engines{7553}

Service Letter-China

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Letter-Asia

Reuse And Salvage Guidelines

Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}

Service Letter-APD

Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock
Certain 7N4160 Switch Groups And 9W1077 Switch Assemblies Need To Be Removed From Parts Stock

Service Magazine

Use FT1711 Light Table For Cylinder Liner Inspection {0652,1216}
1982/11/29

Maintenance Free Batteries{1401}
1986/03/10

New Oil Pressure Switch Used With EMS Systems{7485}
1986/03/10

Requirements For Shipping Wet Batteries In The U.S.{1401,7500}
1986/04/07

Determining The Cause Of Glow Plug Tip Failures{1053,1105,1412}
1986/06/02

Heavy-Duty Line Of Batteries Available To U.S. Dealers{1400,1401}
1986/09/01

Safety Vent Caps For Caterpillar Batteries{1401}
1977/07/11

5P957 And 5P3514 Coolant And Battery Tester{0786,1395,1401}
1987/03/23

Alternator "R" Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04

Alternator/Generator Output Test On The Engine{1401,1404,1405,1406}
1987/05/04

Testing The Starter On The Engine{1401,1450}
1987/05/04

Be Sure Battery Cable-To-Starter Connection Has Correct Torque{1453}
1988/03/14

Maintenance-Free Batteries Require Different Troubleshooting Procedures{1401}
1988/06/20

Revised Instructions For Installation of New Maintenance Free Batteries{1401,1400}
1988/12/12

Fuse And Wire Assembly Is Available For Protection Of Earlier 6N5906 Service Meters{7480}
1979/01/29

Voltage Regulator Can Cause Variable Ammeter Indications{1410,1401,1405,1406,7467}
1979/10/22

Two Plug Assemblies (Booster Cables) Are Available To Start Machines{1401,1453}
1979/11/05

Batteries Can Be Damaged If Too Much Vacuum Is Used During Electrolyte Fill{1401}
1979/11/26

High Performance Maintenance Free Battery Available{1401}
1989/01/16

Limitations On Engine Cranking Time{1453,1401}
1989/03/27

How To Troubleshoot A Short-To-Ground In Power Wiring{1400}
1989/03/27

Preventive Maintenance For Batteries{1401}
1989/03/27

Causes And Effects Of Low Battery Voltage On Electric Starters{1401,1453,1467}
1989/04/24

Procedure For Replacing Batteries Or Battery Cables {1401,1402,1411}
1989/05/01

Procedure For Replacing Batteries, Battery Cables Or Disconnect Switches {1401,1402,1411}
1989/05/01

Special Instruction, "Battery Charging Rate And Time Tables," Available On Oil Resistant Paper{0374,1401}
1989/06/19

Improved 9W1077 Start Switch Assembly And 7N4160 Heat Start Switch Group{1416}
1990/12/10

Compression Ratio Increased On Remanufactured OR1094 & OR1095 Engines To Reduce Amount Of White Smoke On Cold Weather Start-Ups{1000,1254,1290}
1991/09/30

Wiring Harness Conduit Component Sizes {1408}
1995/02/13

Correction to The Pocket Guide, SEBD0402, Is Available as a Reference for Routing and Installing Wire Harness Assemblies {1408}
2000/06/26

Harness Repair of Alternator R-Terminal Connector {1405, 1408, 7553}
2000/10/02

Dielectric Grease Should Not Be Used in Electrical Connectors {1408, 7553}
2012/05/04

Service of the Machined Terminals and the Stamped and Formed Terminals {7553}
2006/11/13

Updated Instruction For The Bypass Harness {0785, 1408}
2008/03/17

Bulk Wiring Harnesses Are Available for Use with Caterpillar Products {1408}
2010/05/12

Striped Wire Is Replaced With Improved Ink Jet Identification for Legacy (Parts Service) Wire harnesses {1408}
2012/06/08

Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553, 7556}
2012/05/08

Information On Battery Cables and Wire Assemblies for Assembling at Dealer Site {4459}
2012/09/21

PROTECTION GP-ENGINE

Testing and Adjusting

General Troubleshooting Information
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Electric Protection System Functional Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Troubleshooting the ETR Full Protective System (OP, WT, OS)
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Troubleshooting the ETR Partial Protection System (OP, WT)
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

CONNECTION GP

Tool Operating Manual

Service Magazine

Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553}
Use Conductive Fasteners for Electrical Grounding on All Cat Products {7553}

RELAY GP

Engine News

Magnetic Switches (Starter Relays) Improved
1988/03/01

Testing and Adjusting

Slave Relay Test
Electric Protection System Energize-To-Run For Generator Set, Industrial and Marine Diesel Engines

Service Magazine

Magnetic Switches (Starter Relays) Improved{1450}
1988/03/14

ELECTRONICS GP-MONITOR

Engine News

New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}
New CAT Inspect Form Available for EMCP Troubleshooting and Inspection {0374, 4490, 7451, 7620}

Special Instruction

Diesel Particulate Filter Monitoring System {108F, 7490}
Diesel Particulate Filter Monitoring System {108F, 7490}

Installation of the Fuel Consumption Monitoring System for All Commercial Diesel Engines {1250, 1400, 1900, 7490}
Installation of the Fuel Consumption Monitoring System for All Commercial Diesel Engines {1250, 1400, 1900, 7490}

Instructions for Installing AssetIQTM for Engine Systems on Caterpillar and non-Caterpillar Products {7490}
Instructions for Installing AssetIQ^TM for Engine Systems on Caterpillar and non-Caterpillar Products {7490}

Cat® VIMS Converter Functionality {7610, 7620}
Cat^® VIMS Converter Functionality {7610, 7620}

Technical Information Bulletin

Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490}
Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490}

Tool Operating Manual

Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}
Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}

Service Magazine

Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
2014/04/08

Improved VisionLinkTM Software Is Now Available for Certain Caterpillar Machines {7601}
2012/06/07

New Software Is Now Available for Cat® Product Link 522 Systems {7494, 7606, 7620}
2012/12/10

Procedure For Improving Compatibility of Product Link Is Now Available on Caterpillar Machines Equipped with Electronic Monitoring Systems (EMS) {7490, 7606}
2013/04/04

Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2014/09/16

New Inspection and Repair Procedure Is Now Available for Cat® Products Located in India Equipped with Product Link {7606}
2014/09/22

New Software Is Now Available for All Cat® Products With PL522 China System {7606, 7620}
2015/03/04

New Troubleshooting Procedure Is Now Available for all Cat® Products Equipped with PL321 VIMS (PL321 VSR) {7606}
2015/05/12

New Software Is Now Available for Cat® Product Link {7606, 7610, 7620}
New Software Is Now Available for Cat^® Product Link {7606, 7610, 7620}

HEATER GP

Engine News

Fuel Heaters Are Now Available For Field Installation
1980/01/09

Troubleshooting Of Jacket Water Heaters
1986/01/01

Horizontally Mounted Jacket Water Heater Now Used
1987/05/01

New Thermostat Used In Jacket Water Heater Group
1993/08/01

A New Thermostat for the Jacket Water Heater {1383}
2006/09/11

Special Instruction

Installation Of 9N3829 Jacket Water Heater Group{1383}
Installation Of 9N3829 Jacket Water Heater Group{1383}

Installation Of 8N9754 Fuel Heater Group{1296}
Installation Of 8N9754 Fuel Heater Group{1296}

Installation of 7E-6310, 9X-3294, 6N-9125, 7E-5244 and 3T-8724 Jacket Water Heater Groups{1383}
Installation of 7E-6310, 9X-3294, 6N-9125, 7E-5244 and 3T-8724 Jacket Water Heater Groups{1383}

Installation Instructions for Jacket Water Heaters with Seal Kits{1383}
Installation Instructions for Jacket Water Heaters with Seal Kits{1383}

Specifications

Jacket Water Heaters
3208 INDUSTRIAL AND MARINE ENGINE ATTACHMENTS

Service Magazine

Fuel Heaters Are Now Available For Field Installation {1296}
1980/01/07

Repair Kit For Diesel Fuel Heater Available {1296}
1983/04/18

Troubleshooting Of Jacket Water Heaters{1383}
1985/12/16

Horizontally Mounted Jacket Water Heater Now Used {1383}
1987/05/11

The Causes And Reduction Of White Exhaust Smoke During Cold Engine Starts; Maintenance Aids Available To Decrease This Problem{1250,1383,1050}
1978/03/13

How To Identify Failures To Electric Jacket Water Heaters{1383}
1988/04/18

General Information -- Diesel Fuels In Cold Temperature Operation{1280}
1979/12/17

New Thermostat Used In Jacket Water Heater Group{1355,1383}
1993/08/23

New Element Assemblies Available Within Jacket Water Heater Groups{1383}
1996/04/15

ELECTRONICS GP-WORK TOOL

Special Instruction

Service Magazine

Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
2014/04/08

Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2014/09/16

ELECTRONICS GP-COMMUNICATION

Engine News

A New Electronic Control Module Wash Out Process {1901, 1920}
A New Electronic Control Module Wash Out Process {1901, 1920}

Special Instruction

Installation Instructions For Product Link 101 Inline Timer{7602}
Installation Instructions For Product Link 101 Inline Timer{7602}

Installation Procedure for Product Link PL522 and PL523 (Cellular) {7606}
Installation Procedure for Product Link PL522 and PL523 (Cellular) {7606}

Technical Information Bulletin

Product Link Registration Problems{733T, 7606}
Product Link Registration Problems{733T, 7606}

Updating to Latest VIMS3G Flash Files And Configuration Files Available For Cat® Machines Equipped With VIMS3G{7601, 7620}
Updating to Latest VIMS3G Flash Files And Configuration Files Available For Cat^® Machines Equipped With VIMS3G{7601, 7620}

Improper Customer Access and Asset Merging Within VisionLinkTM and PartStoreTM Through UCID Consolidation{7567, 7606}
Improper Customer Access and Asset Merging Within VisionLink^TM and PartStore^TM Through UCID Consolidation{7567, 7606}

Tool Operating Manual

Communication Adapter II{0600, 0709, 7600, 7610}
Communication Adapter II{0600, 0709, 7600, 7610}

Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}
Using the 4C-8195 Control Service Tool{0374, 0599, 0709, 7490}

Service Magazine

New Flash File Software Is Used for Product Link 151/201 {7606, 7620}
2002/07/15

New Flexible Antenna Whip Available for Product Link {7606}
2002/12/02

New Processes Improve Registration of Product Link {7338, 7606}
2008/04/14

Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
2014/04/08

New Software Is Now Available for Product Link (PL 121) {7602, 7610, 7620}
2011/12/15

New Software Is Now Available for Cat® Product Link 522 Systems {7494, 7606, 7620}
2012/12/10

Improved Process for Activating Product Link PL522 On Assets In China {7606}
2012/11/19

Improved VisionLink And VisionLink Store Software Are Now Available for All Caterpillar Products {7606, 7620}
2013/11/27

New Software Is Now Available For Product Link 522 Systems On All Cat® Products {7606, 7620}
2013/04/22

Procedure For Improving Compatibility of Product Link Is Now Available on Caterpillar Machines Equipped with Electronic Monitoring Systems (EMS) {7490, 7606}
2013/04/04

Improved VisionLinkTMStore is Now Available for all Caterpillar Products {7606}
2013/03/29

Device Transfers Are Now Supported In VisionLinkTM Store {7606}
2013/03/29

Improved VisionLinkTM Store for Minimizing Delay in Appearance of VisionLink Store - Modules is Now Available for All Caterpillar Products {7606}
2013/03/29

New Product Link Software for PL121 and PL300 Is Now Available for All Cat® Products {7606, 7610, 7620}
2013/05/02

New Software Is Now Available for All Cat® Products With The Product Link 522 System {7606}
2013/09/27

New Product Link Software for PL300 Is Now Available for All Cat® Products {7606, 7620}
2013/07/08

Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2014/09/16

New Software For Cat® ET Can Now Be Used For All Caterpillar Products {0785, 7606}
2013/08/15

New Software Is Now Available For All Cat® Products With PL522 China System {7606, 7620}
2013/08/19

Procedure for Improving Antenna Communication on All Machines Equipped With Product Link {733B, 7606}
2013/09/16

Improvements for Products and Systems Connected to Product Link {7606}
2013/10/02

New Product Link Software for PL300 Is Now Available for All Cat ®Products {7606, 7620}
2013/10/21

New Software Is Now Available for All Cat® Products With The Product Link PL421 or Product Link PL420 System {7606, 7620}
2014/12/10

New Software for Product Link PL522 Module Is Now Available for All Cat® Products {7606}
2014/04/18

Loss of Daily Reports May Be an Indicator of End of Life for the Product Link® ECM on PL321SR and PL321VSR Systems {7606}
2014/06/24

Capturing Engine Stop Messages and Idle Information on All Caterpillar Products Equipped with Product Link 522 {7606}
2014/07/25

Service Meter Adjustment Is Now Available in VisionLinkTM {7478, 7606}
2014/08/20

New Inspection and Repair Procedure Is Now Available for Cat® Products Located in India Equipped with Product Link {7606}
2014/09/22

"Maintenance Mode" in Product Link is Used to Prevent Codes From Being Transmitted When Performing Service to a Machine or Engine {7606}
2014/11/24

Revision to "Reports and Messages Not Available" Troubleshooting Procedure for Cat® Products with Cat® Product Link 121/321 {7606}
2014/12/24

Event Codes (E2131, E2132, or E2133) Appearing Occasionally with On-board Machine Systems with a PL321, or PL121 Satellite System Installed {7600, 7606}
2015/01/06

Procedure to Improve Reporting into VisionLink after Re-Registration of Product Link Systems PL121/321 {7606}
2015/03/17

New Software Is Now Available for All Cat® Products With PL522 China System {7606, 7620}
2015/03/04

New Software for Product Link PL522 Module Is Now Available for All Cat® Products {7606, 7620}
2015/06/26

New Troubleshooting Procedure Is Now Available for all Cat® Products Equipped with PL321 VIMS (PL321 VSR) {7606}
2015/05/12

New Product Link Software for PL300 Is Now Available for All Cat® Products {7606, 7620}
2015/09/11

CAMERA GP

Special Instruction

Generic Installation of the WAVS Cleaning System{7348}
Generic Installation of the WAVS Cleaning System{7348}

Technical Information Bulletin

Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490}
Third-Party Video Streaming Solution for Construction Equipment {7000, 7347, 7348, 7490}

ELECTRONICS GP-GENERATOR SET

Special Instruction

Service Magazine

Auto Clearing of Diagnostics and Events from Electronic Control Module (ECM) {1901, 1920, 7610, 7620}
2014/04/08

Updated Flash Procedure for All Caterpillar Products {1920, 7610, 7620}
2014/09/16

METER GP-SERVICE

Service Meter Adjustment Is Now Available in VisionLinkTM {7478, 7606}
2014/08/20

RECEIVER GP

A New Antenna For The Product Link Is Available {7010, 733T}
2008/06/09

HARNESS GP

Engine News

Wiring Harness Conduit Component Sizes {1408}
1995/02/01

Special Instruction

Procedure to Replace Armature of Starter Motor On All Cat® Products {1408, 1450, 1453}
Procedure to Replace Armature of Starter Motor On All Cat^® Products {1408, 1450, 1453}

Tool Operating Manual

Reuse And Salvage Guidelines

Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}
Guideline for Visual Inspection and Repair of Foam Wiring Harness {0649, 1408, 1408, 1408, 1408}

Service Magazine

Alternator "R" Terminal Wire Assembly Available For Wiring Harness Repair{1408}
1987/05/04

Wiring Harness Conduit Component Sizes {1408}
1995/02/13

Truck sale:

11,500

Caterpillar D3208EP, Construction
- Stationary Generator Sets
FOLEY EQUIPMENT COMPANY

CATERPILLAR 3208 1993
- STATIONARY - DIESEL
WAGNER EQUIPMENT CO
United States

CATERPILLAR 3208 2004
- STATIONARY GENERATOR SETS
EMPRESAS MATCO, S.A. DE C.V.
Sufragio Efectivo Norte 870 - Obregón -

USD $19,000

1998 CAT 3208

Galactic Liquidation LLC

1990 CAT 3208

Ken Porter Auctions
Carson, California