AVSPARE.COM
parts catalog
  1. Home
  2. Caterpillar catalog

9N454 GOVERNOR AND FUEL INJECTION PUMP GROUP 6N1085 Pump and 9N683 Shut-Off parts are shown on Pages 96, 97, 98, 99 and 101. Part of 9N870, 9N457, 4N9231, 4N9184, 4N9223, 4N9227 and 4N9229 Governor and Fuel Injection Pump Groups shown on Pages 90B, 90D, 91, 92, 92A, 92B, 93, 94 and 94A. Only separate parts serviced 3208


FUEL SYSTEM
GOVERNOR GP

ENGINE - MACHINE 3208 ENGINE - MACHINE 90N
 3208 INDUSTRIAL ENGINE 90N00001-06120 UEG0825S 3208 90N   (2018)

FUEL SYSTEM

GOVERNOR GP
GOVERNOR AND FUEL INJECTION PUMP
4N-9227 GOVERNOR AND FUEL INJECTION PUMP
GOVERNOR AND FUEL INJECTION PUMP GROUP
4N-9229 GOVERNOR AND FUEL INJECTION PUMP GROUP
GOV & FUEL INJ PUMP GP
9N-0454 GOV & FUEL INJ PUMP GP
GOVERNOR AND FUEL INJECTION PUMP GROUP
4N-9229 GOVERNOR AND FUEL INJECTION PUMP GROUP
GOV & FUEL INJ PUMP GP
6N-1864 GOV & FUEL INJ PUMP GP
9N-0495 PUMP GP-GOV DRV,FUEL INJ & TFR
 

#UEG0825S0170
 

9N-0454: GOV & FUEL INJ PUMP GP

9N454 GOVERNOR AND FUEL INJECTION PUMP GROUP
6N1085 Pump and 9N683 Shut-Off parts are shown on Pages 96, 97, 98, 99 and
101. Part of 9N870, 9N457, 4N9231, 4N9184, 4N9223, 4N9227 and 4N9229
Governor and Fuel Injection Pump Groups shown on Pages 90B, 90D, 91, 92,
92A, 92B, 93, 94 and 94A. Only separate parts serviced
c205102 UEG0825S
9N0454 GOV & FUEL INJ PUMP GP Parts scheme
  For full view, you need register

Parts for your 3208 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9N-0683 YC [1] SHUT-OFF GROUP  
    (Separate Illustration)
2. 6N-1085 YC [1] PUMP GROUP  
    (Separate Illustration)
3. 4N-4277 [1] SEAT  
4. 4N-4276 [1] SEAT  
5. 4F-7957 [2] BOLT  
6. 3L-5987 [1] COVER  
  6L-5773 [1] GASKET  
  C   INDICATES CHANGE
  Y   SEPARATE ILLUSTRATION
 

#UEG0825S0171
 

4N-9229: GOVERNOR AND FUEL INJECTION PUMP GROUP

4N9229 GOVERNOR AND FUEL INJECTION PUMP GROUP
Serial No. 90N3386-Up. 9N454 Pump and 6N509 Control parts are shown on Pages
94 and 100. Only separate parts serviced. When complete Group is required order
1--9N681 and 1--9N683 Shut-Off shown on Pages 95, 100D and 101
c152002 UEG0825S
4N9229 GOVERNOR AND FUEL INJECTION PUMP GROUP Parts scheme
  For full view, you need register

Parts for your 3208 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9N-0454 YC [1] PUMP GROUP  
    (Separate Illustration)
2. 4N-5663 [1] SPRING  
3. 9L-6508 [1] SPRING  
4. 4N-0443 [1] PIN  
5. 6N-0509 YC [1] CONTROL GROUP  
    (Separate Illustration)
  C   INDICATES CHANGE
  Y   SEPARATE ILLUSTRATION
 

#UEG0825S0172
 

6N-1864: GOV & FUEL INJ PUMP GP

6N1864 GOVERNOR AND FUEL INJECTION PUMP GROUP
Part of 6N1865 and 4N9233 Governor and Fuel Injection Pump Groups shown
on Pages 90A and 90C. 6N1863 Pump and 9N683 Shut-Off parts are shown
on Pages 94D, 94F, 94G, 100D and 101
c221633 UEG0825S
6N1864 GOV & FUEL INJ PUMP GP Parts scheme
  For full view, you need register

Parts for your 3208 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 9N-0683 [ 1] SHUT-OFF GROUP  
2. 6N-1863 Y [ 1] PUMP GROUP  
3. 4F-7957 [ 2] BOLT  
4. 3L-5987 C [ 1] COVER  
  6L-5773 [ 1] GASKET  
5. 4N-0527 [ 1] SPRING  
    SEPARATE ILLUSTRATION
    INDICATES CHANGE
 

#UEG0825S0173
 

9N-0495: PUMP GP-GOV DRV,FUEL INJ & TFR

9N495 GOVERNOR AND FUEL INJECTION PUMP GROUP
Provides Field Replacement for 4N9233 and 6N1865 when used
in conjunction with 9N683 Shut-Off Group
UEG0825S0173 UEG0825S
  For full view, you need register

Parts for your 3208 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
  6N-2337 Y [1] GOVERNOR AND FUEL INJECTION PUMP GROUP  
  4N-5661 [1] SPRING (HIGH IDLE-- 2 WHITE MARKS)  
  4N-9226 [1] SPRING (HIGH IDLE-- 2 GREEN MARKS)  
  6N-2127 [1] SPRING (HIGH IDLE-- 1 PINK MARK)  
  6N-2129 [1] SPRING (HIGH IDLE--2 PINK MARKS)  
  6N-2130 [1] SPRING (HIGH IDLE --1 PINK & 1 YELLOW MARK)  
  6N-2132 [1] SPRING (HIGH IDLE --1 GREEN MARK)  
  4L-6458 [1] NUT  
  8L-8601 [6] SPACER (.002" THICK)  
  9L-3625 [1] TORQUE SPRING (.022" THICK)  
  9L-7235 [3] SHIM (.039" THICK)  
  9L-7630 [2] GASKET-- CROSS OVER PIPE  
  9L-9347 [1] SHIM (.020" THICK)  
  8M-5661 [1] SEAL-- TACHOMETER DRIVE  
  8M-9064 [1] SHIM (.065" THICK)  
  9M-9729 [1] SEAL-- FUEL PUMP HOUSING  
  4N-0508 [1] GASKET (TORQUE SPRING COVER)  
  4N-0532 [1] GASKET (IDLE SCREW COVER)  
  4N-0556 [1] GASKET (GOVERNOR HOUSING)  
  4N-3882 [1] CONTACT  
  4N-7777 [3] SPACER (.010" THICK)  
  4N-9098 [1] SPACER (.200" THICK)  
  1P-6452 [2] INSULATOR  
  1P-6453 [1] BAR (.250" THICK)  
  5S-2619 [1] TORQUE SPRING (.0100" THICK)  
  Y   SEPARATE ILLUSTRATION
 

#UEG0825S0174
 

6N-2337: GOV & FUEL INJ PUMP GP

6N2337 GOVERNOR AND FUEL INJECTION PUMP GROUP
Part of 9N495 Governor and Fuel Injection Pump Group shown on Page 94B
6N1863 Pump and 6N509 Control parts are shown on Pages 94D, 94E, 94F, 94G and 100
c157013 UEG0825S
6N2337 GOV & FUEL INJ PUMP GP Parts scheme
  For full view, you need register

Parts for your 3208 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6N-1863 Y [1] PUMP GROUP  
    (Separate Illustration)
2. 9L-6508 C [1] SPRING (outer)  
3. 4N-8507 [1] COVER  
4. 6N-0509 Y [1] CONTROL GROUP  
    (Separate Illustration)
5. 4F-7957 [4] BOLT  
6. 4N-0117 [1] GASKET  
7. 3L-5987 [1] COVER  
  6L-5773 [1] GASKET  
8. 4N-0443 [1] PIN  
9. 4N-5663 [1] SPRING (inner)  
10. 4N-0527 C [1] SPRING  
  C   INDICATES CHANGE
  Y   SEPARATE ILLUSTRATION
 

#UEG0825S0175
 

6N-1863: GOV & FUEL INJ PUMP GP

6N1863 GOVERNOR AND FUEL INJECTION PUMP GROUP--Part 1 of 4
Part of 6N1864 and 6N2337 Governor and Fuel Injection Pump Groups shown on Pages 94A and 94C
c210111 UEG0825S
6N1863 GOV & FUEL INJ PUMP GP Parts scheme
  For full view, you need register

Parts for your 3208 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6D-0238 [1] VALVE ASSEM.  
2. 030-9208 [1] TEE  
3. 4N-1828 [1] FITTING  
4. 8H-3127 [2] BOLT  
5. 4N-1767 [1] VALVE  
6. 4N-0605 [1] SPRING  
7. 2P-3200 [1] BOLT  
  1J-9671 [1] SEAL  
8. 2M-5471 [4] BOLT  
9. 1D-4533 [3] BOLT 5.72 cm(2.25 in.) long  
10. 8F-8178 [1] BOLT 8.26 cm(3.25 in.) long  
11. 2A-4781 [3] BOLT 6.99 cm(2.75 in.) long  
12. 1D-4716 [1] NUT  
13. 4N-8445 [2] BOLT  
14. 4N-2708 [1] BOLT  
15. 4N-0531 [1] COVER  
  4N-0532 [1] GASKET  
16. 4N-9006 [1] SCREW  
  9M-1311 [1] NUT  
17. 6N-1079 [1] COVER  
  4N-0595 [1] GASKET  
18. 0S-1615 [7] BOLT  
19. 9S-9332 [1] FITTING  
20. 4N-0976 [1] FLANGE  
  1P-2298 [1] VALVE  
  4N-0975 [1] GASKET  
21. 4N-2954 [1] SLEEVE  
22. 4N-0974 [1] FLANGE  
  4N-3088 [1] GASKET  
23. 4N-2773 [1] SHAFT ASSEM.  
  4N-3329 [2] WASHER  
24. 9F-6641 [4] BOLT  
25. 9S-4182 [1] PLUG  
  3J-7354 [1] SEAL  
26. 4N-2334 [8] PIN  
 

#UEG0825S0176
 

6N-1863: GOV & FUEL INJ PUMP GP

6N1863 GOVERNOR AND FUEL INJECTION PUMP GROUP--Part 2 of 4
Part of 6N1864 and 6N2337 Governor and Fuel Injection Pump Groups shown on Pages 94A and 94C
c164828 UEG0825S
6N1863 GOV & FUEL INJ PUMP GP Parts scheme
  For full view, you need register

Parts for your 3208 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 4N-0425 [3] WEIGHT  
  4N-0511 [3] DOWEL  
2. 4N-1809 [1] LEVER ASSEM.  
3. 4N-0556 [1] GASKET  
4. 2P-0910 [2] BOLT  
5. 6N-2024 C [1] HOUSING ASSEM.  
  6N-0343 H [1] STUD  
6. 4N-1826 H [2] DOWEL  
  2D-6392 H [2] SEAL  
7. 4N-5484 [1] VALVE  
  6H-9691 [1] SEAL  
8. 6N-1744 [1] HOUSING ASSEM.  
  9L-9503 [1] DOWEL  
9. 4N-2333 [1] PIN  
10. 8S-6814 [1] DOWEL  
11. 4N-2786 [1] SEAL  
12. 4N-6408 [1] PISTON ASSEM.  
  4N-6407 [1] SPOOL  
13. 4N-6406 [1] RING  
14. 4N-6404 [1] RING  
15. 4N-6403 [1] SEAT  
16. 4N-0406 [1] GEAR  
17. 4N-1132 [1] BODY ASSEM.  
18. 8H-9804 [1] SHAFT  
19. 4N-1584 [1] SEAL  
20. 4N-0636 [1] SEAL  
21. 8S-6814 [1] DOWEL  
22. 4N-0429 [1] GEAR  
23. 4N-3779 [1] KEY  
24. 9L-6542 [1] CAMSHAFT  
  4N-2955 [3] BOLT  
25. 4N-5482 [1] SHAFT  
  4N-9019 [1] DOWEL  
26. 4N-1723 [1] SHIELD  
27. 4N-2953 [1] RING  
28. 4N-2401 [1] BEARING  
  4N-2927 [2] RACE  
29. 4N-0434 [1] RISER  
  4N-0527 [1] SPRING  
30. 4N-3922 [1] LEVER ASSEM.  
31. 4N-9828 [1] SHAFT ASSEM.  
32. 4N-0937 [1] SHAFT  
33. 4N-0940 [1] LEVER  
34. 6D-3031 [2] SCREW  
35. 4N-0563 [1] LEVER  
36. 2N-2658 [2] SCREW  
37. 4N-0446 [1] CARRIER  
38. 9L-6807 [1] SHAFT  
39. 4N-0938 [1] SHAFT  
40. 4N-5579 [1] SEAT ASSEM.  
41. [1] SPRING  
42. 4N-4276 [1] SEAT  
43. 4N-5050 H [1] PLUG  
44. 4N-2333 H [1] PIN  
45. 4N-0935 [1] HOUSING ASSEM.  
46. 4N-3713 [1] SEAL  
47. 4N-0505 [1] GASKET  
48. 4N-5485 [1] BODY  
49. 5F-9144 [1] SEAL  
50. 5M-6509 [1] SEAL  
51. 6N-1078 CH [1] BEARING  
52. 4N-3711 CH [1] BEARING  
  C   INDICATES CHANGE
  H   PART OF 6N2024 HOUSING ASSEM.
 

#UEG0825S0177
 

6N-1863: GOV & FUEL INJ PUMP GP

6N1863 GOVERNOR AND FUEL INJECTION PUMP GROUP--Part 3 of 4
Part of 6N1864 and 6N2337 Governor and Fuel Injection Pump Groups shown on Pages 94A and 94C
c150556 UEG0825S
6N1863 GOV & FUEL INJ PUMP GP Parts scheme
  For full view, you need register

Parts for your 3208 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 3H-0442 [1] SEAL  
2. 2M-7819 [1] RING  
3. 4N-2677 [1] LEVER ASSEM.  
4. 4N-0528 [1] SHAFT  
5. 4N-1591 [1] COVER ASSEM.  
    (Includes)
  4N-0506 [1] COVER  
6. 4N-1594 [1] SCREW  
7. 1P-7326 [1] WASHER  
  8F-1326 [1] WASHER  
  4B-2042 [1] NUT  
  3B-4501 [1] LOCKWASHER  
8. 4N-0445 [1] LEVER  
9. 4N-0523 [1] DOWEL  
  2D-6392 [1] SEAL  
10. 4N-0508 [1] GASKET  
 

#UEG0825S0178
 

6N-1863: GOV & FUEL INJ PUMP GP

6N1863 GOVERNOR AND FUEL INJECTION PUMP GROUP--Part 4 of 4
Part of 6N1864 and 6N2337 Governor and Fuel Injection Pump Groups shown on Pages 94A and 94C
c150555 UEG0825S
6N1863 GOV & FUEL INJ PUMP GP Parts scheme
  For full view, you need register

Parts for your 3208 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 2N-2658 [8] SCREW  
2. 6D-3031 [2] SCREW  
3. 4N-0941 [1] LEVER  
4. 9L-9424 [8] SPRING  
5. 4N-2655 [8] VALVE  
6. 4N-2728 [8] WASHER  
7. 4N-1763 [8] LEVER  
8. 4N-2685 [8] ROLLER  
9. 1P-4001 [1] FITTING  
10. 4N-1750 [8] LIFTER  
11. 4N-4318 [8] SPRING  
12. 4N-1765 [8] PLUNGER AND BARREL ASSEM.  
13. 4N-0224 [8] RING  
14. 4N-0218 [8] BUSHING  
15. 4N-0209 [8] BONNET  
16. 4N-9150 [2] DEFLECTOR  
 

#UEG0825S0179
 

9N-0681: GOV & FUEL INJ PUMP GP

9N681 GOVERNOR AND FUEL INJECTION PUMP GROUP
Pump and Control parts are shown on Pages 96, 97, 98, 99 and 100. Provides Field Replacement for
9N457, 4N9231, 4N9184, 4N9223, 4N9227 and 4N9229 when used in conjunction with 9N683 Shut-Off Group
c222209 UEG0825S
9N0681 GOV & FUEL INJ PUMP GP Parts scheme
  For full view, you need register

Parts for your 3208 ENGINE - MACHINE:

CATERPILLAR SIS
Pos. Part No Qty Parts name Comments
1. 6N-1085 CY [1] GOV & FUEL INJ PUMP GP  
2. 4F-7957 C [4] BOLT  
3. 4N-8507 [1] COVER  
4. 6N-0509 CY [1] TORQUE CONTROL GP  
5. 4N-4276 [1] SEAT-SPRING  
6. 4N-0117 [1] GASKET-SOLENOID  
7. 3L-5987 [1] COVER  
  6L-5773 [1] GASKET  
8. 4N-0443 [1] PIN-LOAD STOP  
9. 4N-4277 [1] SEAT-SPRING  
10. 4N-5663 [1] SPRING (INNER)  
11. 9L-6508 [1] SPRING (OUTER)  
  C   CHANGE FROM PREVIOUS TYPE
  Y   SEPARATE ILLUSTRATION
 

Information:

Engine News
A New 6V29 Sleeve Metering Fuel System Pump Roll Pin Tool Is Used To Adjust And Make A Replacement Of Roll Pins In The Fuel Injection Pump Housing
1979/01/24
Improvements Made To Fuel Injection Pump And Governor Group
1979/03/14
Part Numbers Of Bearings To Use For Service Replacement In Fuel Injection Pump Housings For Sleeve Metering Fuel Systems; Correction To Special Instruction For Installation.
1979/05/09
New Governor Housing Assembly Used In Governor And Fuel Injection Pump Group
1979/08/22
Reverse Flow Check Assembly Now Used In Fuel Injection Pump Assemblies
1980/06/04
New Check Valve Used In Fuel Injection Pump Assembly
1980/06/04
Reverse Flow Check Valves And Check Valves With A Groove Can Not Be Used In Place Of Each Other
1980/10/01
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier
1981/04/01
Check All Settings When Fuel Injection Pump Group Is Installed
1981/04/22
Explanation Of Differences In Timing Advance Information
1981/08/26
New Gasket Used In Governor And Fuel Injection Pump Group
1982/03/17
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator
1982/08/25
FT1698 Driver Can Be Used For Reconditioning Of Governor Housing
1982/10/20
New Seal Used On Governor Control Shaft
1982/12/15
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint
1983/11/30
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier
1984/01/18
New Fuel Injection Pumps, Fuel Injection Lines, Fuel Injection Nozzles, and Piston And Rod Groups Used On Some Engines
1984/08/22
New Outer Governor Spring And Torque Control Pin Used In Governor And Pump Groups
1985/04/01
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings
1985/12/01
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing
1986/03/01
Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control
1986/04/01
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers
1986/06/01
Update Information For Caterpillar Fuel Injection Equipment Test Stand
1986/07/01
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas
1986/10/01
Initial Start Of Engine Using An EGB29P Governor/Actuator After Filling With Oil
1987/05/01
Four More Remanufactured Fuel Pump And Governor Groups Available
1987/09/01
Orifice Reverse Flow Check Valve Used In Fuel Injection Pumps
1987/12/01
Governor Springs For Sleeve Metering Fuel Systems
1990/06/01
Dowel Hole Removed From 8N3946 Governor Housing Improves Service Life
1991/07/01
New Spring Used In Governor Control Groups
1992/04/01
New Hold-Down Bolts For The Sleeve Metering Fuel System (SMFS) Governor Housing {1251}
1996/09/23
Drains In New Fuel Injection Pump Housing And Governor Housing Prevent Possible Corrosion And Freezing Damage
1977/03/15
Correct Adjustment Of Fuel Shut-Off Solenoid Shaft Can Prevent Failures
1977/07/13
Changes To The Injection Pump And The Fuel Setting
1977/09/28
Use The Drive Sleeve On The Fuel Injection Pump Camshaft Only One Time
1978/07/05
Improved Guide Pin For Fuel Injection Pump Lifters
1978/08/30
Special Instruction
Using The 6V4060 Engine Set Point Indicator Group{0781}
Using The 6V4060 Engine Set Point Indicator Group{0781}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
"A Series" Governor And Air/Fuel Ratio Control Response And Low Power Test{0374}
Installation of Fuel Injection Pump and Governor Service Group{1286}
Installation of Fuel Injection Pump and Governor Service Group{1286}
Installation Of 5P4810 Bearing In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of 5P4810 Bearing In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of Short Block Group For 3208 Or Cylinder Block Service Group For 1100, 3100 And 3208 Engines{1201, 1203, 1286}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of 8N628 Service Replacement Bearing For Rear Of Injection Pump Camshaft In Sleeve Metering Fuel Injection Pump Housing{1253}
Installation Of Governor Spring Guide{1264}
Installation Of Governor Spring Guide{1264}
Installation Of 8N628 Bearing{7551, 1253}
Installation Of 8N628 Bearing{7551, 1253}
Use Of FT1525 Alignment Pin, FT1526 Salvage Fixture And FT1698 Bearing Installation Tool For Reconditioning Of 3208 Governor Housings{1265, 1264}
Use Of FT1525 Alignment Pin, FT1526 Salvage Fixture And FT1698 Bearing Installation Tool For Reconditioning Of 3208 Governor Housings{1265, 1264}
Use Of 6V4068 Tool Group For Installation Of 9N5822 Thrust Washer{1253}
Use Of 6V4068 Tool Group For Installation Of 9N5822 Thrust Washer{1253}
Using the 6V7870 Fixture Group and 6V7872 Pliers{1250, 1251}
Using the 6V7870 Fixture Group and 6V7872 Pliers{1250, 1251}
Service Letter-NACD
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Service Letter-Australia
Service Letter-CFEL
Service Letter-CSARL
Service Letter-Americas
Service Letter-Brazil
Service Letter-Truck/Ag/Marine
Specifications
Fuel Injection Pump
3208 INDUSTRIAL & MARINE ENGINES
Governor
3208 INDUSTRIAL & MARINE ENGINES
Service Letter-China
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Certain 7N0449, 1W5829, 4W1819, 4W8483, 7W3710 And 1010060 Nozzles Assemblies Need To Be Removed From Parts Stock
Service Letter-Asia
Service Letter-APD
Disassembly and Assembly
Fuel Injection Pump Housing & Governor
3208 INDUSTRIAL & MARINE ENGINES
Check Valve & Bypass Valve
3208 INDUSTRIAL & MARINE ENGINES
Fuel Injection Pumps
3208 INDUSTRIAL & MARINE ENGINES
Fuel Transfer Pump
3208 INDUSTRIAL & MARINE ENGINES
Governor
3208 INDUSTRIAL & MARINE ENGINES
Service Magazine
Use The FT1525 Alignment Pin And FT1526 Fixture When Reconditioning Earlier 3208 Sleeve Metering Fuel Systems{0626,1264,1286}
1980/05/12
New Check Valve Used In Fuel Injection Pump Assembly{1251}
1980/05/26
Reverse Flow Check Assembly Now Used In Fuel Injection Pump Assemblies{1251,1272,1254}
1980/06/02
Reverse Flow Check Valves And Check Valves With A Groove Can Not Be Used In Place Of Each Other{1251,1272,1254}
1980/09/15
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1981/02/23
6V2029 Fixture Group Available For Adjustment Of Air/Fuel Ratio Control {0626,1278,0652}
1981/03/23
Fuel Pressure Relief Valve Is Shown Inverted (Wrong End Up) In Parts Book Illustrations {1253,1286}
1981/03/23
Check All Settings When Fuel Injection Pump Group Is Installed{1286,1264,1251,1253}
1981/03/30
FT1632 Bolt Used During Removal Of Sleeve From Sleeve Metering Fuel System{0621,1251,1253}
1981/08/31
Thrust Washer Used In Pump Housing For Sleeve Metering Fuel System{1253,1286}
1981/08/31
Bent Lever For Fuel Shut-Off Solenoid Can Cause Low Engine Performance{1286,1259}
1982/02/01
New Gasket Used In Governor And Fuel Injection Pump Group{1259,1286}
1982/03/01
Make Set Point Measurements Easier With The 6V4060 Engine Set Point Indicator{0651}
1982/08/16
Modification Of 2P8315 Bracket Assembly{0652,1286}
1982/08/16
FT1698 Driver Can Be Used For Reconditioning Of Governor Housing{0626,0665,1264,1286}
1982/10/18
New Seal Used On Governor Control Shaft{1264,1265}
1982/11/22
Explanation Of Engine High Idle RPM And Correct Adjustment Of Engine Setpoint{1264}
1983/11/07
6V4163 Bit And 6V4164 Driver Now Available For Removal Of Bolts For Flyweight Carrier{0612,1264}
1983/12/05
New Fuel Injection Pumps, Fuel Injection Lines, Fuel Injection Nozzles, and Piston And Rod Groups Used On Some Engines{1000,1225,1251,1252,1254}
1984/08/13
New Outer Governor Spring And Torque Control Pin Used In Governor And Pump Groups{1264}
1985/04/08
Check Fuel Injection Nozzles In Overheated Engines{1254}
1985/09/02
Comparison Of Fuel Timing Tolerances For Field Settings{1250,1251,1281}
1985/10/28
Anti-Seize Compound And/Or Grease Not To Be Used On Fuel Pump Bonnet Retaining Bushings{1251}
1985/11/11
Nylon Seals Used On Lockwire To Seal Critical Areas; Parts Service Seals Available For NACD Dealers{1257,1264}
1986/03/10
Improved Sleeve Bearing Used In Drive End Of Fuel Injection Pump Housing{1253}
1986/03/10
Incorrect Connection Of Battery Charger Can Open Circuit Breaker And Damage Woodward 2301 Governor Control{1400,1401,4450}
1986/03/24
Black Nylon Fuel Seals For Lockwire Available Only To NACD Dealers For Certain Customers{1257,1264}
1986/06/09
Changes Have Been Made To OT Microfiche (Fuel Setting And Related Information){1250,1251,1281}
1986/06/16
More Flexible Lockwire Used With Nylon Seals For Sealing Critical Areas{1257,1264}
1986/09/22
Nylon Seals Used On Lockwire To Seal Critical Areas; All Subsidiary Dealers Can Now Order Parts Service Seals {1257,1264}
1986/11/03
Drains In New Fuel Injection Pump Housing And Governor Housing Prevent Possible Corrosion And Freezing Damage{1286}
1977/03/07
Changes To The Injection Pump And The Fuel Setting{1251,1257}
1977/09/19
Use Correct Contact Point With Dial Indicator To Be Sure Of The Accuracy Of The Measurements Of Fuel Setting And Fuel Ratio Control Setting On Sleeve Metering Fuel Systems{0653,1250}
1977/09/26
Improved High Idle Display Of The 6V3100 And 8T5300/8T5301 Engine Timing Indicator Groups{0781}
1987/03/16
Four More Remanufactured Fuel Pump And Governor Groups Available {1286}
1987/09/14
Orifice Reverse Flow Check Valve Used In Fuel Injection Pumps{1251,1254}
1987/11/23
Do Not Change Factory Fuel Or Speed Settings On Truck Engines Unless New Settings Are Certified Under Applicable EPA Regulations{0336,0337,1257}
1978/01/30
Do Not Use The 5B1401 Cleaning Tool Group To Clean The Orifice In Capsule-Type Fuel Injection Nozzles{0650,1254}
1978/04/24
Stronger Fuel Inlet Flanges Prevent Parts Damage And Keeps Air Out Of The Fuel System{1253}
1978/05/15
Use The Drive Sleeve On The Fuel Injection Pump Camshaft Only One Time{1286,1256,1251}
1978/07/03
Improved Guide Pin For Fuel Injection Pump Lifters{1251}
1978/08/21
Use New 6V22 Tool Group To Make Replacement Of Worn Governor Spring Guides{0620}
1978/09/25
Modification To Rack Adjusting Tool Needed For Higher Rack Settings{0654,1257}
1978/10/16
Check Valve Added To Keep Air From Entering Fuel System {1264}
1988/10/03
Improvements Made To Fuel Injection Pump And Governor Group{1253,1281,1286}
1979/03/05
Part Numbers Of Bearings To Use For Service Replacement In Fuel Injection Pump Housings For Sleeve Metering Fuel Systems; Correction To Special Instruction For Installation.{1253}
1979/05/07
9S8100 Tool Group Changed To Use With Fuel Transfer Pump Only{0622}
1979/05/28
Changes Made To 8S2243 And 8S4613 Wrenches Used On Fuel Injection Pumps{0612,1251}
1979/08/06
New Governor Housing Assembly Used In Governor And Fuel Injection Pump Group{1253,1264}
1979/08/27
Tee Handle Hexagonal Wrench In Rack Adjusting Tool Is Now Available For Parts Replacement
1979/09/10
Governor Springs For Sleeve Metering Fuel Systems {1264}
1990/05/21
Dowel Hole Removed From 8N3946 Governor Housing Improves Service Life{1287}
1991/07/08
New Spring Used In Governor Control Groups{1265}
1992/04/20
Tamper Resistant Plugs And Tamper Resistant Bolts Used To Prevent Changes To Fuel Ratio Control (FRC) Setting{1278,1287}
1996/01/22

Caterpillar Parts SIS Catalog 3208 :

GOVERNOR AND FUEL INJECTION PUMP GROUP
4N-9229 GOVERNOR AND FUEL INJECTION PUMP GROUP
GOVERNOR AND FUEL INJECTION PUMP
4N-9227 GOVERNOR AND FUEL INJECTION PUMP
GOVERNOR AND FUEL INJECTION PUMP GROUP
4N-9223 GOVERNOR AND FUEL INJECTION PUMP GROUP
GOVERNOR AND FUEL INJECTION PUMP GROUP
4N-9223 GOVERNOR AND FUEL INJECTION PUMP GROUP
GOVERNOR AND FUEL INJECTION PUMP GROUP
4N-9184 GOVERNOR AND FUEL INJECTION PUMP GROUP
GOVERNOR AND FUEL INJECTION PUMP GROUP
4N-9184 GOVERNOR AND FUEL INJECTION PUMP GROUP
GOVERNOR AND FUEL INJECTION PUMP GROUP
4N-9231 GOVERNOR AND FUEL INJECTION PUMP GROUP
GOV & FUEL INJ PUMP GP
9N-0457 GOV & FUEL INJ PUMP GP
GOVERNOR AND FUEL INJECTION PUMP GROUP
4N-9229 GOVERNOR AND FUEL INJECTION PUMP GROUP
GOV & FUEL INJ PUMP GP
6N-1864 GOV & FUEL INJ PUMP GP
9N-0495 PUMP GP-GOV DRV,FUEL INJ & TFR
GOV & FUEL INJ PUMP GP
6N-2337 GOV & FUEL INJ PUMP GP
GOV & FUEL INJ PUMP GP
6N-1863 GOV & FUEL INJ PUMP GP
GOV & FUEL INJ PUMP GP
6N-1863 GOV & FUEL INJ PUMP GP
GOV & FUEL INJ PUMP GP
6N-1863 GOV & FUEL INJ PUMP GP
GOV & FUEL INJ PUMP GP
6N-1863 GOV & FUEL INJ PUMP GP

Truck sale:

 
11,500 
Caterpillar D3208EP, Construction
- Stationary Generator Sets
FOLEY EQUIPMENT COMPANY
CATERPILLAR 3208 1993
 
CATERPILLAR 3208 1993
- STATIONARY - DIESEL
WAGNER EQUIPMENT CO
United States
CATERPILLAR 3208 2004
 
CATERPILLAR 3208 2004
- STATIONARY GENERATOR SETS
EMPRESAS MATCO, S.A. DE C.V.
Sufragio Efectivo Norte 870 - Obregón -
1998 CAT 3208
USD $19,000 
1998 CAT 3208

Galactic Liquidation LLC
1990 CAT 3208
 
1990 CAT 3208

Ken Porter Auctions
Carson, California
Back to top
Contacts Request list Affiliate disclosure
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.