4K8562 UNION Caterpillar parts
950
Rating:
Alternative (cross code) number:
CA4K8562
4K-8562
4K8562
CA4K8562
4K-8562
4K8562
Weight: 1 pounds 0 kg.
WHEEL LOADER,
Compatible equipment models: 4K8562:
Number on catalog scheme:
None
For full view, you need register
Information:
Removal Procedure
Start By:
Remove the Electronic Control Module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
Illustration 1 g02164253
Illustration 2 g02164254
Cut cable straps (2) from wiring harness assembly. Note: Note the position of cable straps that attach the wiring harness assembly to the ECM mounting bracket.
Remove bolt (3) (not shown) from clip for tube assembly (4).
Remove the fuel line from clips on the ECM mounting bracket.
Slide locking tab into the unlocked position. Disconnect wiring harness (7) from atmospheric pressure sensor (8).
Remove bolts (5) and loosen bolts (6) sufficiently to the allow ECM mounting bracket to be removed. Remove ECM mounting bracket (1) from the cylinder block.
If necessary, remove atmospheric pressure sensor (8) from the ECM mounting bracket. Refer to Disassembly and Assembly, "Atmospheric Pressure Sensor - Remove and Install" for the correct procedure. Installation Procedure
Illustration 3 g02164254
Illustration 4 g02164253
Ensure that ECM mounting bracket (1) for the electronic control module is clean and free from damage. If the mounting bracket is damaged, replace the bracket.
If necessary, install atmospheric pressure sensor (8) to ECM mounting bracket (1). Tighten the atmospheric pressure sensor to a torque of 10 N m (89 lb in). Refer to Disassembly and Assembly, "Atmospheric Pressure Sensor - Remove and Install" for the correct procedure.
Position mounting bracket (1) onto bolts (6).
Install remaining bolts (5) to mounting bracket (1).
Tighten bolts (5) and bolts (6) to a torque of 22 N m (195 lb in).
Connect harness assembly (7) to atmospheric pressure sensor (8). Slide the locking tab into the locked position.
Install fuel line to clips onto the ECM mounting bracket.
Install bolt (3) (not shown) to clip for tube assembly (4). Tighten the bolt to a torque of 22 N m (195 lb in).
Position the wiring harness assemblies onto the ECM mounting bracket. Install new cable straps to the wiring harness assemblies. Note: Ensure that the cable straps meet the Original Equipment Manufactures (OEM) specifications.End By:
Install the electronic control module. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
Start By:
Remove the Electronic Control Module (ECM). Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
Illustration 1 g02164253
Illustration 2 g02164254
Cut cable straps (2) from wiring harness assembly. Note: Note the position of cable straps that attach the wiring harness assembly to the ECM mounting bracket.
Remove bolt (3) (not shown) from clip for tube assembly (4).
Remove the fuel line from clips on the ECM mounting bracket.
Slide locking tab into the unlocked position. Disconnect wiring harness (7) from atmospheric pressure sensor (8).
Remove bolts (5) and loosen bolts (6) sufficiently to the allow ECM mounting bracket to be removed. Remove ECM mounting bracket (1) from the cylinder block.
If necessary, remove atmospheric pressure sensor (8) from the ECM mounting bracket. Refer to Disassembly and Assembly, "Atmospheric Pressure Sensor - Remove and Install" for the correct procedure. Installation Procedure
Illustration 3 g02164254
Illustration 4 g02164253
Ensure that ECM mounting bracket (1) for the electronic control module is clean and free from damage. If the mounting bracket is damaged, replace the bracket.
If necessary, install atmospheric pressure sensor (8) to ECM mounting bracket (1). Tighten the atmospheric pressure sensor to a torque of 10 N m (89 lb in). Refer to Disassembly and Assembly, "Atmospheric Pressure Sensor - Remove and Install" for the correct procedure.
Position mounting bracket (1) onto bolts (6).
Install remaining bolts (5) to mounting bracket (1).
Tighten bolts (5) and bolts (6) to a torque of 22 N m (195 lb in).
Connect harness assembly (7) to atmospheric pressure sensor (8). Slide the locking tab into the locked position.
Install fuel line to clips onto the ECM mounting bracket.
Install bolt (3) (not shown) to clip for tube assembly (4). Tighten the bolt to a torque of 22 N m (195 lb in).
Position the wiring harness assemblies onto the ECM mounting bracket. Install new cable straps to the wiring harness assemblies. Note: Ensure that the cable straps meet the Original Equipment Manufactures (OEM) specifications.End By:
Install the electronic control module. Refer to Disassembly and Assembly, "Electronic Control Module - Remove and Install" for the correct procedure.
Caterpillar parts catalog:
Parts union Caterpillar catalog:
6S5064
UNION
824B, 834, 992
824B, 834, 992
7K2094
UNION
992
992
3779550
UNION
793F, 793F CMD, 793F OEM, 793F-XQ, 988K, 993K
793F, 793F CMD, 793F OEM, 793F-XQ, 988K, 993K
3574349
UNION AS
980K, 980K HLG
980K, 980K HLG
2877285
UNION AS
844H, 990H
844H, 990H
3574351
UNION AS
966H, 972H
966H, 972H
3196248
UNION AS
784C, 785C, 785D, 789D, 793D, 795F AC, 795F XQ, 797, 797B, 797F
784C, 785C, 785D, 789D, 793D, 795F AC, 795F XQ, 797, 797B, 797F
1697390
UNION AS
D250E II, D300E II
D250E II, D300E II
769D, 771D, 773D, 773E, 775D, 775E, 776D, 777D, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 793B, 793C, 793D, 797B
769C, 773B, 777, 777B, 784B, 785, 785B, 789B, 793, 793B, 793C, AD40, AD45, AE40, R1700 II
1645563
UNION AS
1090, 1190, 1190T, 1290T, 2290, 2384C, 2390, 2391, 2484C, 2491, 511, 521, 522, 532, 559C, 579C, 784C, 785C, 785D, 789C, 793C, 793D, TK711, TK721, TK722, TK732
1090, 1190, 1190T, 1290T, 2290, 2384C, 2390, 2391, 2484C, 2491, 511, 521, 522, 532, 559C, 579C, 784C, 785C, 785D, 789C, 793C, 793D, TK711, TK721, TK722, TK732
1T0129
UNION
980F
980F