1932737 V-BELT Caterpillar parts
308C, 308D
Rating:
Alternative (cross code) number:
CA1932737
193-2737
1932737
CA1932737
193-2737
1932737
Weight: 0.22 pounds 0 kg.
MINI HYD EXCAVATOR,
This part in 2 request:
Show.
This information for suppliers only!
2022-08-25
2021-05-17
Number on catalog scheme:
1
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all harness assemblies, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g00690963
Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.
Illustration 2 g01216058
Remove bolts (1) and platform (2).
Illustration 3 g01216060
Disconnect hose assemblies (3), (5), (6), and (7).
Remove bolts (4) and drift reduction valve (8).
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic System Pressure - Release".
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products.Dispose of all fluids according to local regulations and mandates.
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all harness assemblies, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g00690963
Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 276 to 414 kPa (40 to 60 psi) of air. This procedure will pull vacuum on the hydraulic system.
Illustration 2 g01216058
Remove bolts (1) and platform (2).
Illustration 3 g01216060
Disconnect hose assemblies (3), (5), (6), and (7).
Remove bolts (4) and drift reduction valve (8).
Caterpillar parts catalog:
Parts v Caterpillar catalog:
305.5, 306, 307D, 308C, 308D
2013913
V-BELT
307D, 308C, 308D
307D, 308C, 308D
2013913
V-BELT
307D, 308C, 308D
307D, 308C, 308D
305.5, 306, 307D, 308C, 308D
311C, 312C L, 314C
305
303, 305
2060659
V-BELT
305
305
2142102
V-BELT
304
304
2206406
V-BELT
302.5C, 304, 305
302.5C, 304, 305
1992376
V-BELT
303
303
318C, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 323D L, 323D LN, 323D SA
2553015
V-BELT
314C
314C
311B, 312B, 314C, 320B L