1P3085 V-BELT Caterpillar parts
1090, 1190, 1190T, 1290T, 12F, 1390, 914G, D7F, IT14G
Rating:
Alternative (cross code) number:
CA1P3085
1P-3085
1P3085
CA1P3085
1P-3085
1P3085
Weight: 0.30 pounds 0 kg.
Information:
EFFECTIVE LENGTH
1232
mm
GROOVE WIDTH
12.7
mm
COMPACT WHEEL LOADER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Fakojer 2X V-Belt 6N-3113 9N-1323 111-0575 1P-3085 Compatible with Caterpillar CAT Engine 3046 3054 3064 3204 3208 Loader 933 939 910G 914G Tractor D3G D4G D5G D7F
Fakojer Part Number: 1110575, 1P3085, 6N3113, 9N1323, 111-0575, 1P-3085, 6N-3113, 9N-1323, CA1110575, CA1P3085, CA6N3113, CA9N1323 || Fits: Compatible with Caterpillar CAT Engine: 3046, 3054, 3064, 3204, 3208; Track-Type Skidder: 4P, D4HTSK II, 54H; Track-Type Tractor: 3, D3C III, D3G, D4C III, D4G, D4H, D5C III, D5G, D5C PAT, D5C PATLGP, D7F; Track Feller Buncher: 1090, 1190, 1390, 1190T, 1290T; Integrated Toolcarrier: IT14G, IT18, IT18B, IT28, IT28B. Please see description for more details || Type: V-Belt || Condition: New, Replacement Part || Quantity: 2. Please make sure that the part number and item you need match the one in the link
Fakojer Part Number: 1110575, 1P3085, 6N3113, 9N1323, 111-0575, 1P-3085, 6N-3113, 9N-1323, CA1110575, CA1P3085, CA6N3113, CA9N1323 || Fits: Compatible with Caterpillar CAT Engine: 3046, 3054, 3064, 3204, 3208; Track-Type Skidder: 4P, D4HTSK II, 54H; Track-Type Tractor: 3, D3C III, D3G, D4C III, D4G, D4H, D5C III, D5G, D5C PAT, D5C PATLGP, D7F; Track Feller Buncher: 1090, 1190, 1390, 1190T, 1290T; Integrated Toolcarrier: IT14G, IT18, IT18B, IT28, IT28B. Please see description for more details || Type: V-Belt || Condition: New, Replacement Part || Quantity: 2. Please make sure that the part number and item you need match the one in the link
Aftermarket 2 Pieces V-Belt 111-0575 1P-3085 6N-3113 9N-1323 Fit Intended For Engine 3046 3054 3064 3204 3208 Loader 933 939 910G 914G 916 926 Tractor D3G D4G D5G D7F
Generic
Generic
FridayParts Replacement 2 Pieces V-Belt 111-0575 1P-3085 6N-3113 9N-1323 Compatible for Caterpillar CAT Engine 3046 3054 3064 3204 3208 Loader 933 939 910G 914G 916 926 Tractor D3G D4G D5G D7F
FP FRIDAYPARTS New aftermarket parts || Part Number: 111-0575, 1P-3085, 6N-3113, 9N-1323, 1110575, 1P3085, 6N3113, 9N1323, CA1110575, CA1P3085, CA6N3113, CA9N1323 || Compatible for Caterpillar CAT Engine 3046, 3054, 3064, 3204, 3208, Loader 933, 939, 910G, 914G, 916, 926, Tractor D3G, D4G, D5G, D7F || Please verify your part number before ordering, if you have any question please don't hesitate to contact us
FP FRIDAYPARTS New aftermarket parts || Part Number: 111-0575, 1P-3085, 6N-3113, 9N-1323, 1110575, 1P3085, 6N3113, 9N1323, CA1110575, CA1P3085, CA6N3113, CA9N1323 || Compatible for Caterpillar CAT Engine 3046, 3054, 3064, 3204, 3208, Loader 933, 939, 910G, 914G, 916, 926, Tractor D3G, D4G, D5G, D7F || Please verify your part number before ordering, if you have any question please don't hesitate to contact us
Compatible equipment models: 1P3085:
Information:
Remove Cylinder Head
start by:a) remove rocker armb) remove fuel injection linesc) remove turbochargerd) remove exhaust manifold 3304 Engine is shown.1. Disconnect the tube assembly from the turbocharger air elbow. Remove four bolts, elbow and gasket from head. 2. Remove the water temperature sending unit (2) from elbow (4).3. Remove bolts (1) and (3) that fasten elbow (4) to the cylinder head and the water pump. 4. Fasten a hoist and tooling (A) to cylinder head.5. Remove bolts (5) that hold the cylinder head to the cylinder block. Remove the cylinder head and gasket. The weight of the cylinder head is 150 lb. (68 kg). When the cylinder head is removed, a new spacer plate gasket must be installed. See REMOVE AND INSTALL SPACER PLATE.Install Cylinder Head
1. Clean the surfaces of the cylinder head and the cylinder block that make contact with each other. Make sure the surfaces are clean and dry. Install a new, dry gasket (1) on the cylinder block.2. Fasten a hoist and tooling (A) to the cylinder head (2) and put it in position on the cylinder block.3. Put 5P3931 Anti-Seize Compound on all the head bolts and rocker shaft bolts. Install the head bolts and washers that hold the head in place. Do not tighten the bolts at this time. 4. Install the push rods (4) and rocker shaft assembly (3). Make sure the dowel (5) in the bracket assembly is in alignment in the cylinder head.5. Install the bolts and washers that hold the rocker shaft assembly in place.
3304 ENGINE
3306 ENGINE6. Tighten the bolts as follows: a) Tighten bolts in number sequence to a torque of 115 lb.ft. (155 N m).b) Tighten bolts again in number sequence to a torque of 185 13 lb.ft. (250 17 N m).c) Tighten bolts again in number sequence to a torque of 185 13 lb.ft. (250 17 N m).d) Tighten bolts in letter sequence to a torque of 32 lb.ft. (43 7 N m).e) Tighten bolts again in letter sequence to a torque of 32 lb.ft. (43 7 N m).7. Make adjustment until the intake valve is .015 in. (0.38 mm) and the exhaust valve clearance is .025 in. (0.64 mm). See ENGINE VALVE LASH as shown in operation LUBRICATION AND MAINTENANCE GUIDE. Tighten the locknuts for the adjustment screws to a torque of 22 3 lb.ft. (28 4 N m). 8. Inspect both gaskets on the elbow and make a replacement if necessary. Install elbow (6) in position on the water pump and the cylinder head.9. Install the water temperature sending unit (7) in elbow (6).10. Install the turbocharger air elbow and gasket in position on the cylinder head. Connect the tube assembly to the turbocharger air elbow.end by:a) install exhaust manifoldb) install turbochargerc) install fuel injection lines
start by:a) remove rocker armb) remove fuel injection linesc) remove turbochargerd) remove exhaust manifold 3304 Engine is shown.1. Disconnect the tube assembly from the turbocharger air elbow. Remove four bolts, elbow and gasket from head. 2. Remove the water temperature sending unit (2) from elbow (4).3. Remove bolts (1) and (3) that fasten elbow (4) to the cylinder head and the water pump. 4. Fasten a hoist and tooling (A) to cylinder head.5. Remove bolts (5) that hold the cylinder head to the cylinder block. Remove the cylinder head and gasket. The weight of the cylinder head is 150 lb. (68 kg). When the cylinder head is removed, a new spacer plate gasket must be installed. See REMOVE AND INSTALL SPACER PLATE.Install Cylinder Head
1. Clean the surfaces of the cylinder head and the cylinder block that make contact with each other. Make sure the surfaces are clean and dry. Install a new, dry gasket (1) on the cylinder block.2. Fasten a hoist and tooling (A) to the cylinder head (2) and put it in position on the cylinder block.3. Put 5P3931 Anti-Seize Compound on all the head bolts and rocker shaft bolts. Install the head bolts and washers that hold the head in place. Do not tighten the bolts at this time. 4. Install the push rods (4) and rocker shaft assembly (3). Make sure the dowel (5) in the bracket assembly is in alignment in the cylinder head.5. Install the bolts and washers that hold the rocker shaft assembly in place.
3304 ENGINE
3306 ENGINE6. Tighten the bolts as follows: a) Tighten bolts in number sequence to a torque of 115 lb.ft. (155 N m).b) Tighten bolts again in number sequence to a torque of 185 13 lb.ft. (250 17 N m).c) Tighten bolts again in number sequence to a torque of 185 13 lb.ft. (250 17 N m).d) Tighten bolts in letter sequence to a torque of 32 lb.ft. (43 7 N m).e) Tighten bolts again in letter sequence to a torque of 32 lb.ft. (43 7 N m).7. Make adjustment until the intake valve is .015 in. (0.38 mm) and the exhaust valve clearance is .025 in. (0.64 mm). See ENGINE VALVE LASH as shown in operation LUBRICATION AND MAINTENANCE GUIDE. Tighten the locknuts for the adjustment screws to a torque of 22 3 lb.ft. (28 4 N m). 8. Inspect both gaskets on the elbow and make a replacement if necessary. Install elbow (6) in position on the water pump and the cylinder head.9. Install the water temperature sending unit (7) in elbow (6).10. Install the turbocharger air elbow and gasket in position on the cylinder head. Connect the tube assembly to the turbocharger air elbow.end by:a) install exhaust manifoldb) install turbochargerc) install fuel injection lines
Caterpillar parts catalog:
Parts v Caterpillar catalog:
1478910
V-BELT
938G, 950G, 962G, IT38G
938G, 950G, 962G, IT38G
2116557
V-BELT
938G, 950G, 962G, IT38G
938G, 950G, 962G, IT38G
1986890
V-BELT
938G, IT38G
938G, IT38G
1601821
V-BELT
950G, 962G, 980G, IT62G
950G, 962G, 980G, IT62G
1986827
V-BELT
938G, 950G, 962G, IT38G, IT62G
938G, 950G, 962G, IT38G, IT62G
7E1362
V-BELT
914G, 930G, IT14G, IT14G2
914G, 930G, IT14G, IT14G2
2433098
V-BELT
901C
901C
4383524
V-BELT
901C, 902C, 903C
901C, 902C, 903C
3979969
V-BELT
906H2, 907H2, 908H2
906H2, 907H2, 908H2
3044010
V-BELT
906H, 907H, 908H
906H, 907H, 908H
2715183
V-BELT
904B, 904H
904B, 904H
9Y6117
V-BELT
950G II, 962G II, IT62G II
950G II, 962G II, IT62G II