V-BELT SET 2441244 - Caterpillar

2441244 V-BELT SET Caterpillar parts 3508, 3508B

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2441244
244-1244
2441244

Weight: 3 pounds 1 kg.

Buy V-BELT SET 2441244 Caterpillar genuine, new aftermarket tractor parts with delivery
GENERATOR SET,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

AAF 2441244 OEM Replacement Cartridge Filter, Nanofiber FR Filter Media, 12.74" OD, 26" Length

$171.66

01 Apr 2022

Amazon.com

AAF 2441244 OEM Replacement Cartridge Filter, Nanofiber FR Filter Media, 12.74" OD, 26" Length
Damn Filters Composition: Fire-Retardant Nanofiber (80/20 media with a synthetic layer applied electrostatically) || Maximum Continuous Temperature Resistance: 175° F || Thickness: 0.022" || Air Permeability: 28 cfm Frazier || Filtration Efficiency: Merv 15. 99.97% efficient @ .3 microns

AAF 2441244 OEM Replacement Cartridge Filter, Cellulose/Polyester Blend Filter Media, 12.74" OD, 26" Length

$132.59

01 Apr 2022

Amazon.com

AAF 2441244 OEM Replacement Cartridge Filter, Cellulose/Polyester Blend Filter Media, 12.74" OD, 26" Length
Damn Filters Composition: Cellulose/Polyester paper blend || MERV Rating: MERV 11 - 99.95% efficient @ .5 microns || Continuous Max Temp: 180° || Air Permeability: 23 cfm feet squared @ 0.5" W.C. || Flow Rate: 5.6 FPM

AAF 2441244 OEM Replacement Cartridge Filter, Spun Bond Polyester Filter Media, 12.74" OD, 26" Length

$212.98

01 Apr 2022

Amazon.com

AAF 2441244 OEM Replacement Cartridge Filter, Spun Bond Polyester Filter Media, 12.74" OD, 26" Length
Damn Filters Composition: 100% Spun bonded Polyester || Maximum Continuous Temperature Resistance: 200° F. || Thickness: 0.022" || Air Permeability: 28 CFM Frazier || Filtration Efficiency: MERV 12 BIA Classification U.S.G and C. 99.9% when tested against Quartz Dust with 90% particles lying between 1.2um and 2um. Filtration Velocity = 3.36 m/min.

This part in 8 request: Show. This information for suppliers only!

2023-04-12

2023-04-12

2023-02-18

2023-02-09

2022-11-23

2019-06-19

2017-04-17

2017-03-28

Number on catalog scheme: 34

Caterpillar 2441244 Parts scheme V-BELT SET

For full view, you need register

Compatible equipment models: 2441244:

GENERATOR SET 3508 3508B Caterpillar

Information:

Illustration 1 g01349887
Connections of the reverse solenoid for the right pump
This diagnostic code is associated with the reverse solenoid for the right pump. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal.The possible causes of this diagnostic code are listed:
The solenoid has failed.
The energize circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This is unlikely. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 1706 FMI 03 is active before performing this procedure.Note: Use a digital multimeter for the measurements in this procedure.System Response:A level 2 warning is generated. The action lamp will be ON and flashing.Test Step 1. CHECK THE SOLENOID CIRCUIT FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the solenoid and the ECM.
At the machine harness connector for the ECM, measure the resistance from contact J1-52 (wire 849-YL(Yellow)) to all contacts that are used in the machine harness connectors for the ECM. Expected Result:Each resistance measurement should be greater than 5000 ohms.Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to test step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between contact J1-52 (wire 849-YL(Yellow)) and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE OPERATION OF THE ECM.The disconnect switch and the key start switch remain in the OFF position. The machine harness connectors for the solenoid and the ECM remain disconnected.
At the J1 connector for the ECM, use a wire removal tool to remove wire 849-YL(Yellow) from contact J1-52.
Reconnect the machine harness J1 and J2 connectors to the ECM.
Turn the disconnect switch and the key start switch to the ON position.
Observe the status of the active diagnostic code. Expected Result:The FMI 03 changes to an FMI 05 after the wire is disconnected.Results:
YES - The FMI 03 changes to a FMI 05 after the wire is disconnected. The ECM has responded correctly to the condition of an open circuit. Reinstall the disconnected wire to the correct space in the ECM connector before proceeding to the next Test Step. Proceed to Test Step 3.
NO - The FMI 03 remains active. The status of the active diagnostic code did not change when the wire was disconnected from the ECM.Repair: The ECM has not responded correctly to the condition of an open circuit. The operation of the ECM is not correct. Prior to replacing an ECM, always contact your dealership for possible consultation with Caterpillar. This consultation may greatly reduce repair time. If the ECM requires replacing, refer to Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOPTest