2P6819 V-BELT Caterpillar parts
627E, 920, 930, 941, 953B, 953C, D250E, D250E II, D25D, D300E, D300E II
Rating:
Alternative (cross code) number:
CA2P6819
2P-6819
2P6819
CA2P6819
2P-6819
2P6819
Weight: 0.30 pounds 0 kg.
Information:
EFFECTIVE LENGTH
1168
mm
GROOVE WIDTH
12.7
mm
ARTICULATED TRUCK, WHEEL TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 2P6819 External Engine V-Belt
CTP For External Engine || Highly Efficient || Easy in-and-out fit
CTP For External Engine || Highly Efficient || Easy in-and-out fit
D&D PowerDrive 2P6819 Caterpillar Replacement Belt, 17, 1 -Band, 46.27" Length, Rubber
D&D PowerDrive The belts exceed USA RMA published ratings levels || They are designed to perform at the identical or higher level than all other major USA manufacturer's belts of the same Type || Belt 17 .53 inches x 46.27 inches oc || Package weight: 1.02 lbs
D&D PowerDrive The belts exceed USA RMA published ratings levels || They are designed to perform at the identical or higher level than all other major USA manufacturer's belts of the same Type || Belt 17 .53 inches x 46.27 inches oc || Package weight: 1.02 lbs
Number on catalog scheme:
4
For full view, you need register
Compatible equipment models: 2P6819:
Information:
Inspect
Belt tension should be checked initially between the first 20 to 40 hours of engine operation.After the initial check, the belt tension should be checked at every oil change.To maximize the engine performance, inspect the belts for wear and for cracking. Replace belts that are worn or damaged.For applications that require multiple drive belts, replace the belts in matched sets. Replacing only one belt of a matched set will cause the new belt to carry more load because the older belt is stretched. The additional load on the new belt could cause the new belt to break.If the belts are too loose, vibration causes unnecessary wear on the belts and pulleys. Loose belts may slip enough to cause overheating.If the belts are too tight, unnecessary stresses are placed on the pulley bearings and on the belts. This may shorten the service life of the components.Remove the belt guard, if equipped. Inspect the condition and adjustment of the alternator belts and accessory drive belts (if equipped).If the belt does not require replacement or adjustment, install the belt guard. If the belt requires adjustment or replacement, follow the procedure below.Adjust/Replace (V-Belts)
The engine may be equipped with one of the belts below.Alternator Belt
Illustration 1 g02533519
(1) Adjusting nuts
(2) Mounting bolts
Slightly loosen the mounting bolts and the adjusting nuts.
To check the belt tension on v-belts, apply 110 N (25 lb ft) of force midway between the pulleys. A correctly adjusted belt will deflect 9 mm (0.35 inch) to 15 mm (0.59 inch).
If necessary, tighten or loosen the adjustment nuts to adjust the belt tension.
If necessary, remove the belt guard and replace the belts. Note: Always replace v-belts in sets. Never replace one belt from a set.
Tighten adjusting the nuts and the mounting bolts. Refer to the Specifications Manual, SENR3130, "Torque Specifications" topic.
If new belts are installed, check the belt tension after 30 minutes of engine operation at the rated rpm.
Install the belt guard. Belt for the Water Pump
Illustration 2 g02533616
(3) Mounting bolt
(4) Square hole
(5) Adjusting bolt
Slightly loosen the mounting bolt and the adjusting bolt.
To check the belt tension on v-belts, apply 110 N (25 lb ft) of force midway between the pulleys. A correctly adjusted belt will deflect 9 mm (0.35 inch) to 15 mm (0.59 inch).
Adjust the belt tension with a square drive in the square hole.
If necessary, remove the belt guard and replace the belts. Note: Always replace v-belts in sets. Never replace one belt from a set.
Tighten the adjusting bolt and mounting bolt. Refer to the Specifications Manual, SENR3130, "Torque Specifications."
If new belts are installed, check the belt tension after 30 minutes of engine operation at the rated rpm.
Install the belt guard. Replace (Serpentine Belt)
The tension on the serpentine belt may not be adjusted.
Illustration 3 g02533916
(6) Square hole
Remove the front cover.
Insert a
Belt tension should be checked initially between the first 20 to 40 hours of engine operation.After the initial check, the belt tension should be checked at every oil change.To maximize the engine performance, inspect the belts for wear and for cracking. Replace belts that are worn or damaged.For applications that require multiple drive belts, replace the belts in matched sets. Replacing only one belt of a matched set will cause the new belt to carry more load because the older belt is stretched. The additional load on the new belt could cause the new belt to break.If the belts are too loose, vibration causes unnecessary wear on the belts and pulleys. Loose belts may slip enough to cause overheating.If the belts are too tight, unnecessary stresses are placed on the pulley bearings and on the belts. This may shorten the service life of the components.Remove the belt guard, if equipped. Inspect the condition and adjustment of the alternator belts and accessory drive belts (if equipped).If the belt does not require replacement or adjustment, install the belt guard. If the belt requires adjustment or replacement, follow the procedure below.Adjust/Replace (V-Belts)
The engine may be equipped with one of the belts below.Alternator Belt
Illustration 1 g02533519
(1) Adjusting nuts
(2) Mounting bolts
Slightly loosen the mounting bolts and the adjusting nuts.
To check the belt tension on v-belts, apply 110 N (25 lb ft) of force midway between the pulleys. A correctly adjusted belt will deflect 9 mm (0.35 inch) to 15 mm (0.59 inch).
If necessary, tighten or loosen the adjustment nuts to adjust the belt tension.
If necessary, remove the belt guard and replace the belts. Note: Always replace v-belts in sets. Never replace one belt from a set.
Tighten adjusting the nuts and the mounting bolts. Refer to the Specifications Manual, SENR3130, "Torque Specifications" topic.
If new belts are installed, check the belt tension after 30 minutes of engine operation at the rated rpm.
Install the belt guard. Belt for the Water Pump
Illustration 2 g02533616
(3) Mounting bolt
(4) Square hole
(5) Adjusting bolt
Slightly loosen the mounting bolt and the adjusting bolt.
To check the belt tension on v-belts, apply 110 N (25 lb ft) of force midway between the pulleys. A correctly adjusted belt will deflect 9 mm (0.35 inch) to 15 mm (0.59 inch).
Adjust the belt tension with a square drive in the square hole.
If necessary, remove the belt guard and replace the belts. Note: Always replace v-belts in sets. Never replace one belt from a set.
Tighten the adjusting bolt and mounting bolt. Refer to the Specifications Manual, SENR3130, "Torque Specifications."
If new belts are installed, check the belt tension after 30 minutes of engine operation at the rated rpm.
Install the belt guard. Replace (Serpentine Belt)
The tension on the serpentine belt may not be adjusted.
Illustration 3 g02533916
(6) Square hole
Remove the front cover.
Insert a
Caterpillar parts catalog:
Parts v Caterpillar catalog:
3056E, 3114, 3116, 3126, CP-563, CS-563C, CS-573C, CS-583C, D25C, D25D, D300B, D30C, D350C, D35C, E110B, E120B, E200B, E240C
3114, 3116, 3126, 613, 918F, 924F, 950F II, 960F, AD55, D250E, D250E II, D25D, D300D, D300E, D300E II, IT18F, IT24F
3126, 953B, 963B, 963C
3114, 3116, 3126, 533, 543, 918F, 924F, 953B, AP-1000, AP-1000B, AP-1050, AP-1055B, BG-2455C, BG-245C, CB-434, CB-634C, CB-634D, CP-563, CS-531C, CS-533, CS-533C, CS-563C, CS-573C, CS-583C, IT12B, IT2...
120H, 120H ES, 120H NA, 135H, 135H NA, 214B, 30/30, 3114, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 325B L, 35, 446, 446B, 446D, 45, 525B, 535B, 539, 55, 550, 561M, 570, 574, 580...
3208, 525B, 535B, 75, 75C, 75D, 75E, 814, 815, 816, 85D, 85E, 920, 930, 955K, 955L, 95E, 966C, D4E, D6D, RM-350B, SM-350
3208, 416C, 416D, 420D, 424D, 426C, 428C, 428D, 430D, 432D, 436C, 438C, 438D, 442D, 815B, 950B, 953B, 953C, 963, 980G II, 980H, 986H, CB-434D, CB-534D, CB-564D, CD-54, CS-54, D3G, D4G, D5G, E110B, E12...
627E, 65, 65C
216, 236, 247, 267, 287, 420E, 430E, 432E, 434E, 442E, 444E, 824G, 825G, 826G, 920, 951B, 980G, D4D
428, 621E, 621F, 623E, 623F, 627E, 627F, D10N, D250B, D8H, D8R, D8R II
120, 3208, 941, 951B, 966C, D6C, D6D
3126B, 3408, 3408C, 3412, 3412C, 3412E, 578, 583R, 587R, 621E, 621F, 621G, 623E, 623G, 627E, 627F, 627G, D8N
953C
938F, 950F, 950F II, 960F, 963B
776C, 777B, 963B
928G, 963B, IT28G
533, 543, 933, 933C, 939, 939C, D3C III, D4C III, D4D, D5C III, TK370, TK371, TK380
950F, 953B
928F, 938F, 950F II, 960F, 963C, IT28F, IT38F
561M, D5M, D6M
D6R
561M, D5M, D6M
