9L4896 V-BELT GP Caterpillar parts
3116, 3306B, C7, C9, CX31-C9I, TH31-E61
Rating:
Alternative (cross code) number:
CA9L4896
9L-4896
9L4896
CA9L4896
9L-4896
9L4896
Weight: 0.30 pounds 0 kg.
Information:
EFFECTIVE LENGTH
1016
mm
GROOVE WIDTH
12.7
mm
GEN SET ENGINE, PETROLEUM TRANSMISSION,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
9L4896 V BELT Suitable For Caterpillar® 9L4896
KMP BRAND Suitable for Caterpillar
KMP BRAND Suitable for Caterpillar
RAParts One New Replacement Belt Fits White 303315134 Fits CAT 9L6177 9L4896
Reliable Aftermarket Parts One New Aftermarket Replacement REC Fan Belt || OC Length: 40.27" || Material: Polyester Cord || Width: 0.531" || Replaces Part Numbers: 303077276, 203007009, 203003568, 155985A, 72160795, 303315134
Reliable Aftermarket Parts One New Aftermarket Replacement REC Fan Belt || OC Length: 40.27" || Material: Polyester Cord || Width: 0.531" || Replaces Part Numbers: 303077276, 203007009, 203003568, 155985A, 72160795, 303315134
D&D PowerDrive 9L4896 Caterpillar Replacement Belt, 17, 1 -Band, 40.270000000000003" Length, Rubber
D&D PowerDrive The belts exceed USA RMA published ratings levels || They are designed to perform at the identical or higher level than all other major USA manufacturer's belts of the same Type || Belt 17 .53 inches x 40.27 inches oc || Made in China
D&D PowerDrive The belts exceed USA RMA published ratings levels || They are designed to perform at the identical or higher level than all other major USA manufacturer's belts of the same Type || Belt 17 .53 inches x 40.27 inches oc || Made in China
This part in 10 request:
Show.
This information for suppliers only!
2024-01-29
2023-06-05
2023-04-06
2022-05-29
2022-04-18
2022-03-14
2021-07-01
2021-03-29
2021-02-18
2018-12-07
Number on catalog scheme:
1
For full view, you need register
9L4896
Images:
Compatible equipment models: 9L4896:
Information:
Illustration 1 g00564355
7W-2743 Electronic Speed Switch (ESS) (1) Push button for Overspeed Verification (2) Reset button (3) Overspeed indicator lamp (4) Seal screw plug for adjusting the engine overspeed (5) Seal screw plug for adjusting the crank terminate speed (6) Seal screw plug for adjusting the oil step pressure speed settingThe procedure for the magnetic pickup test will determine if the operation of the magnetic pickup is correct.
Connect a 6V-7070 Digital Multimeter to the "COM" terminal and the "SIG" terminal. The terminals are (ESS-3)and (ESS-4) of the ESS. Set the meter voltage scale to a scale that is greater than 1.5 VAC. Start the engine. Run the engine at low idle or 600 rpm. Choose the one that is larger.If the voltage that is measured is 1.5 VAC or more, the operation of the magnetic pickup is correct. If the voltage is less than 1.5 VAC, go to Step 2.
Stop the engine. Disconnect the wiring for the magnetic pickup at the plug-in connector. Connect the voltmeter to the connector terminals of the magnetic pickup. Start the engine. Run the engine at low idle or 600 rpm. Choose the one that is larger.If the voltage that is measured is 1.5 VAC or more, repair the wiring that is between the magnetic pickup and the ESS. If the voltage is less than 1.5 VAC, go to Step 3.
Illustration 2 g00564913
Magnetic pickup (1) Clearance (2) Magnetic pickup (3) Wires to the connector (4) Locknut (5) Flywheel housing (6) Ring gear
Loosen locknut (4) and turn magnetic pickup (2) in the counterclockwise direction in order to remove magnetic pickup (2) from flywheel housing (5). Turn the flywheel until a gear tooth of ring gear (6) is directly in the center of the threaded hole for magnetic pickup (2). Install magnetic pickup (2) in flywheel housing (5) .
Turn magnetic pickup (2) in the clockwise direction until the end of magnetic pickup (2) slightly touches the gear tooth. Turn the magnetic pickup for one-half turn in the counterclockwise direction in order to set correct clearance (1). Tighten locknut (4) to a torque of 45 7 N m (33 5 lb ft).Note: Do not allow the magnetic pickup to turn while the locknut is tightened.
Repeat Step 2. If the voltage is still less than 1.5 VAC, replace the magnetic pickup.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts v Caterpillar catalog:
3306, 3306B
3304, 3306B
3304, 3306, 3306B
214B, 3054, 3056, 3056E, 3116, 3126B, 3306B, 977H, AP-1000, AP-1050, D250B, M316C, M318, M318C, M318C MH, M320, M322C
3126B, 3176C, 3196, C-10, C-12, C-9, C7, C9, CX31-C9I, D6D, D6E, TH31-E61
14G, 3126B, 3176C, 3196, 920, 977L, C-10, C-12, C-9, C7, C9, CX31-C9I, D5, D5H, D5H XL, D6C, D6D, D6D SR, D6E SR, TH31-E61
3126B, 3176C, 3196, 65, 65C, 70C, C-10, C-12, C-9, C7, C9, CX31-C9I, D7F, TH31-E61
3126B, 3176C, 3196, 983, C-10, C-12, C-9, C7, C9, CX31-C9I, D6C, D7G, TH31-E61
C7, D6R II
120G, 12G, 130G, 140G, 304E, 305.5E, 305E, 416B, 426B, 428B, 908, C9
305.5E, C9
906, C-9, C9, CX31-C9I, TH31-E61
120H ES, 120H NA, 135H NA, 3306, 3306B, G3306
3304, 3306, 3508, 3512, 3516
1673, 3304, 3306, 3306B
1673C, 215, 3114, 3116, 3126, 3306B, 768B, 769, 983
1469255
V.A. BOOM
312B L
312B L
4450293
V-BELT GP
CB24B
CB24B
3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 3456, C-15, C-16, C15, C18, C9.3, CX31-C15I, CX35-P800, TH35-C15I
325 FM L, 325 L, 3406, 3406B, 3406C, 3406E, 3408, 3412, 3412E, C-15, C-16, C13, C9.3, CX31-C13I, G3406, TH48-E70
3054B, 3056, 3056E, 3208, 3406B, 3408, CP-573E, CP-663E, CS-563E, CS-583E, CS-663E, CS-683E
3304, 3306, 3306B
3304, 3306B
3306, 3306B