1057313 VALVE GP-FLOW CONTROL Caterpillar parts
322, 322 FM L, 322 LN, 322B, 322B L, 322B LN
Rating:
Alternative (cross code) number:
CA1057313
105-7313
1057313
CA1057313
105-7313
1057313
Weight: 0.90 pounds 0 kg.
EXCAVATOR,
Number on catalog scheme:
37
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 230-7923 Spanner Wrench As 1
C 2P-8312 Retaining Ring Pliers 1
D 129-1938 Grease Cartridge -
Illustration 1 g01023136
Use a suitable lifting device in order to install knuckle (17). The weight of knuckle (17) is approximately 50 kg (110 lb).
Illustration 2 g01023130
Do not install shims (14) at this time. Install pin assembly (13). Install bolts (12). Do not tighten bolts (12) at this time.
Apply Tooling (D) to the surface of pin assembly (15). Install pin assembly (15) and bolts (16). Tighten bolts (16) to a torque of 300 N m (221 lb ft).
Illustration 3 g01023126
Install wheel flange (10) and bearing cone (11).
Illustration 4 g01023088
Install ring gear (9).
Illustration 5 g01047569
Use Tooling (B) and install spanner nut (3). Tighten spanner nut (3) to a torque of 1000 N m (738 lb ft). Install locking plate (4) and bolts (5). Tighten bolts (5) to a torque of 70 N m (52 lb ft). Note: If the tab on locking plate (4) does not line up with the slot in spanner nut (3), tighten spanner nut (3) until the slot and the tab are aligned.
Illustration 6 g01023074
Illustration 7 g01023075
Use a suitable pry bar and push the double U-joint toward the wheel flange. This will make the installation of retaining ring (8) easier. Install washer (6) and thrust washer (7). Use Tooling (D) and install retaining ring (8).
Illustration 8 g01029956
Insert a suitable pry bar and move the knuckle up and down while you tighten bolts (12). Tighten bolts (12) until there is no end play. Use a suitable feeler gauge and measure the clearance between pin assembly (13) and the knuckle. Measure the clearance at several points and average the measurement. Use shims (14) that equal the measurement.
Remove pin assembly (13). Apply Tooling (D) to the surface of pin assembly (13). Install pin assembly (13), the correct shims (14), and bolts (12). Tighten bolts (12) to a torque of 300 N m (221 lb ft).
Illustration 9 g01032913
Install tie rod end (1) into the axle housing. Install nut (2). Tighten nut (2) to a torque of 220 N m (162 lb ft). End By:
Install the final drive planetary.
Table 1
Required Tools
Tool Part Number Part Description Qty
B 230-7923 Spanner Wrench As 1
C 2P-8312 Retaining Ring Pliers 1
D 129-1938 Grease Cartridge -
Illustration 1 g01023136
Use a suitable lifting device in order to install knuckle (17). The weight of knuckle (17) is approximately 50 kg (110 lb).
Illustration 2 g01023130
Do not install shims (14) at this time. Install pin assembly (13). Install bolts (12). Do not tighten bolts (12) at this time.
Apply Tooling (D) to the surface of pin assembly (15). Install pin assembly (15) and bolts (16). Tighten bolts (16) to a torque of 300 N m (221 lb ft).
Illustration 3 g01023126
Install wheel flange (10) and bearing cone (11).
Illustration 4 g01023088
Install ring gear (9).
Illustration 5 g01047569
Use Tooling (B) and install spanner nut (3). Tighten spanner nut (3) to a torque of 1000 N m (738 lb ft). Install locking plate (4) and bolts (5). Tighten bolts (5) to a torque of 70 N m (52 lb ft). Note: If the tab on locking plate (4) does not line up with the slot in spanner nut (3), tighten spanner nut (3) until the slot and the tab are aligned.
Illustration 6 g01023074
Illustration 7 g01023075
Use a suitable pry bar and push the double U-joint toward the wheel flange. This will make the installation of retaining ring (8) easier. Install washer (6) and thrust washer (7). Use Tooling (D) and install retaining ring (8).
Illustration 8 g01029956
Insert a suitable pry bar and move the knuckle up and down while you tighten bolts (12). Tighten bolts (12) until there is no end play. Use a suitable feeler gauge and measure the clearance between pin assembly (13) and the knuckle. Measure the clearance at several points and average the measurement. Use shims (14) that equal the measurement.
Remove pin assembly (13). Apply Tooling (D) to the surface of pin assembly (13). Install pin assembly (13), the correct shims (14), and bolts (12). Tighten bolts (12) to a torque of 300 N m (221 lb ft).
Illustration 9 g01032913
Install tie rod end (1) into the axle housing. Install nut (2). Tighten nut (2) to a torque of 220 N m (162 lb ft). End By:
Install the final drive planetary.
Caterpillar SIS machinery equipment:
Caterpillar SIS
322L EXCAVATOR 9RL00001-UP (MACHINE) POWERED BY 3116 ENGINE »
105-7313
VALVE GP-FLOW CONTROL
322 L, 322 LN AND 322 N EXCAVATORS 4RM00001-UP (MACHINE) POWERED BY 3116 ENGINE »
105-7313
VALVE GP-FLOW CONTROL
322B L Excavator 1YS00001-UP (MACHINE) POWERED BY 3116 Engine »
105-7313
VALVE GP-FLOW CONTROL
322B L & 322B LN Excavators 1ZS00001-UP (MACHINE) POWERED BY 3116 Engine »
105-7313
VALVE GP-FLOW CONTROL
322 322L TRACK-TYPE EXCAVATORS 7WL00001-UP (MACHINE) POWERED BY 3116 ENGINE »
105-7313
VALVE GP
322B & 322B L TRACK-TYPE EXCAVATORS 8MR00001-UP (MACHINE) POWERED BY 3116 ENGINE »
105-7313
VALVE GP-FLOW CONTROL
322B L TRACK-TYPE EXCAVATOR /HAMMER ARRANGEMENT/ 1AS00001-UP (MACHINE) POWERED BY 3116 ENGINE »
105-7313
VALVE GP-FLOW CONTROL
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
320, 320 L, 320B L, 320N, 322, 322 FM L, 325, 325 FM L, 325 L, 325 LN, 330, 330 FM L, 330 L
318C, 319C, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D L, 321C, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D L, 325B L, 325C, 325C FM, 325D, 325D FM, 325D L, 329D, 329D L, 330B L, 330C, 3...
320, 320 L, 320N, 322, 322 FM L, 322 LN, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, M325B
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 311D LRR, 312D, 315D L, 318C, 319C, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D L, 320D LRR, 320D RR, 321C, 321D ...
311B, 311D LRR, 312B, 312B L, 312C L, 312D, 312D L, 315B, 315B FM L, 315B L, 315C, 315D L, 317B LN, 318B, 319D L, 319D LN, 320B, 320B FM LL, 320B L, 320B U, 321B, 322B, 322B L, 322B LN, 322C, 322C FM,...
312C, 312C L, 315C, 318C, 319C, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320C L, 321B, 321C, 322B, 322B L, 322B LN, 322C, 322C FM, 325B, 325B L, 325C, 325C FM, 330B, 330B L, 330C, 330C FM, 330C L, 330...
318C, 320C, 320C FM, 320D, 320D FM, 320D L, 320D LN, 320D LRR, 320D RR, 321C, 321D LCR, 322 FM L, 322C, 323D L, 324D, 324D L, 325 FM L, 325 L, 325C, 329D, 329D L, 330, 330 FM L, 330 L, 330C, 330C L, 3...
320, 320 L, 320N, 322, 325, 325 L, 325 LN, 330, 330 FM L, 330 L
320, 320 L, 320N, 322, 322 FM L, 322 LN, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, M325B
120H, 120H ES, 120H NA, 135H, 135H NA, 206B, 211B, 213B, 214B, 3114, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 325, 325B, 325B L, 35, 446B, 446D, 45, 525B, 533, 535B, 539, 543, 5...
120G, 120H, 120H ES, 120H NA, 12G, 12H, 12H ES, 12H NA, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 16G, 16H NA, 205B, 214B, 224...
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140B, 140G, 140H, 140H ES, 140H NA, 140M, 140M 2, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 160M, 160M 2, 163H NA, 1673C, 215, 225, 235, 235B, 3116, 3176, ...
1303382
VALVE GP-CONTROL
322, 322 FM L
322, 322 FM L
1303381
VALVE GP-CONTROL
322, 322 FM L
322, 322 FM L
322, 322 FM L, 322 LN
1165836
VALVE GP-CONTROL
322, 322 FM L, 322 LN
322, 322 FM L, 322 LN
1163571
VALVE GP-CHECK & RELIEF
322 FM L, 322 LN
322 FM L, 322 LN
322 FM L, 322 LN
6E3033
VALVE GP-RELIEF
120H, 120H NA, 120K, 12H, 12H NA, 12K, 135H, 135H NA, 140H, 140H NA, 140K, 143H, 14H NA, 160H, 160H NA, 160K, 163H NA, 16H NA
120H, 120H NA, 120K, 12H, 12H NA, 12K, 135H, 135H NA, 140H, 140H NA, 140K, 143H, 14H NA, 160H, 160H NA, 160K, 163H NA, 16H NA
6E2866
VALVE GP-COMBINATION
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16H NA, 24H
120H, 120H ES, 120H NA, 12H, 12H ES, 12H NA, 135H, 135H NA, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 16H NA, 24H
1538910
VALVE GP-BANK 6
120H, 120H ES, 120H NA, 12H, 135H, 135H NA, 140H, 140H NA, 143H, 160H, 160H NA, 163H NA
120H, 120H ES, 120H NA, 12H, 135H, 135H NA, 140H, 140H NA, 143H, 160H, 160H NA, 163H NA
1537964
VALVE & LINKAGE GP
120H, 120H ES, 120H NA, 12H, 135H, 135H NA, 140H, 140H NA, 143H, 160H, 160H NA, 163H NA
120H, 120H ES, 120H NA, 12H, 135H, 135H NA, 140H, 140H NA, 143H, 160H, 160H NA, 163H NA
1325404
VALVE GP-CONTROL
3306C
3306C
1157579
VALVE GP-SOLENOID
322 FM L, 325, 330
322 FM L, 325, 330