1073672 VALVE AS-RELIEF Caterpillar parts
315, 315B, D5C III
Rating:
Alternative (cross code) number:
CA1073672
107-3672
1073672
CA1073672
107-3672
1073672
Weight: 0.40 pounds 0 kg.
EXCAVATOR, TRACK-TYPE TRACTOR,
Number on catalog scheme:
20
For full view, you need register
Information:
Fuel setting is the adjustment of the fuel setting screw to a specified position. The fuel setting screw limits the power output of the engine by setting the maximum travel of all the fuel injector racks.
Illustration 1 g00559781
4C-6594 Timing and Fuel Setting Tool (1) 5P-4814 Collet Clamp (2) 6V-3075 Dial Indicator (3) 5P-7263 Indicator Contact Point Before the fuel setting is checked, the fuel injectors must be correctly synchronized. Refer to System Operation, Testing and Adjusting, "Fuel Injector Synchronization".
Illustration 2 g00559811
Fuel injection linkage control housing (4) Synchronizing pin (5) Fuel setting screw (6) Fuel setting cover (Y) Location for the dial indicator (Z) Location for the synchronizing pin
Remove the plugs from the housing assembly at location (Y) and (Z) .
Remove synchronizing pin (4), and install the pin in the threaded hole at location (Z) without the washer. Tighten the synchronizing pin.
Illustration 3 g01346243
Installation of the synchronizing pin (4) Synchronizing pin (5) Fuel setting screw (6) Fuel setting cover (7) Fuel stop lever (Y) Location for the dial indicator
Move the actuator terminal shaft lever in the "FUEL ON" direction until the flat face of fuel stop lever (7) contacts synchronizing pin (4) .
Illustration 4 g00560054
Installation of 6V-3075 Dial Indicator (2) 6V-3075 Dial Indicator (4) Synchronizing pin
Put 6V-3075 Dial Indicator (2) with 5P-7263 Contact Point (3) in 5P-4814 Collet clamp (1) .
Install the dial indicator (2) and the collet in the threaded hole at location (Y). When the contact point seats against fuel stop lever (7), slide the dial indicator inward or slide the dial indicator outward until the dial indicator gives a reading of 0.00 mm (0.000 inch). Tighten the collet enough in order to hold the dial indicator in position.
Remove synchronizing pin (4). Slowly move the actuator terminal shaft in the "FUEL ON" direction until the flat face of fuel stop lever (7) is against the end of the fuel setting screw (5). When the linkage is held in this position, the dial indicator reading will be the present fuel setting.
Illustration 5 g00341652
Engine information plateNote: See the information plate on the engine for the correct fuel setting for full static load.
If the fuel setting is correct, remove the dial indicator. Return the synchronizing pin and the washer to the original locations.
Install the plugs at location (Y) and (Z) .
If the fuel setting needs adjustment, go on to "Fuel Setting Adjustment".Fuel Setting Adjustment
A mechanic with governor and fuel setting training is the ONLY one to make adjustments to the engine fuel setting.
Note: Before the fuel setting adjustment is made, check the fuel setting. Refer to "Fuel Setting Check".Refer to Illustrations 2 through 4.
Cut the seal wire and remove fuel setting cover (6) and the gasket. Loosen the locknut. While "Surface A" of fuel stop lever (7) is held against the end of fuel setting screw (5) turn the fuel setting screw inward or turn the fuel setting screw outward. Turn the fuel setting screw inward or turn the fuel setting screw outward until the correct reading is
Illustration 1 g00559781
4C-6594 Timing and Fuel Setting Tool (1) 5P-4814 Collet Clamp (2) 6V-3075 Dial Indicator (3) 5P-7263 Indicator Contact Point Before the fuel setting is checked, the fuel injectors must be correctly synchronized. Refer to System Operation, Testing and Adjusting, "Fuel Injector Synchronization".
Illustration 2 g00559811
Fuel injection linkage control housing (4) Synchronizing pin (5) Fuel setting screw (6) Fuel setting cover (Y) Location for the dial indicator (Z) Location for the synchronizing pin
Remove the plugs from the housing assembly at location (Y) and (Z) .
Remove synchronizing pin (4), and install the pin in the threaded hole at location (Z) without the washer. Tighten the synchronizing pin.
Illustration 3 g01346243
Installation of the synchronizing pin (4) Synchronizing pin (5) Fuel setting screw (6) Fuel setting cover (7) Fuel stop lever (Y) Location for the dial indicator
Move the actuator terminal shaft lever in the "FUEL ON" direction until the flat face of fuel stop lever (7) contacts synchronizing pin (4) .
Illustration 4 g00560054
Installation of 6V-3075 Dial Indicator (2) 6V-3075 Dial Indicator (4) Synchronizing pin
Put 6V-3075 Dial Indicator (2) with 5P-7263 Contact Point (3) in 5P-4814 Collet clamp (1) .
Install the dial indicator (2) and the collet in the threaded hole at location (Y). When the contact point seats against fuel stop lever (7), slide the dial indicator inward or slide the dial indicator outward until the dial indicator gives a reading of 0.00 mm (0.000 inch). Tighten the collet enough in order to hold the dial indicator in position.
Remove synchronizing pin (4). Slowly move the actuator terminal shaft in the "FUEL ON" direction until the flat face of fuel stop lever (7) is against the end of the fuel setting screw (5). When the linkage is held in this position, the dial indicator reading will be the present fuel setting.
Illustration 5 g00341652
Engine information plateNote: See the information plate on the engine for the correct fuel setting for full static load.
If the fuel setting is correct, remove the dial indicator. Return the synchronizing pin and the washer to the original locations.
Install the plugs at location (Y) and (Z) .
If the fuel setting needs adjustment, go on to "Fuel Setting Adjustment".Fuel Setting Adjustment
A mechanic with governor and fuel setting training is the ONLY one to make adjustments to the engine fuel setting.
Note: Before the fuel setting adjustment is made, check the fuel setting. Refer to "Fuel Setting Check".Refer to Illustrations 2 through 4.
Cut the seal wire and remove fuel setting cover (6) and the gasket. Loosen the locknut. While "Surface A" of fuel stop lever (7) is held against the end of fuel setting screw (5) turn the fuel setting screw inward or turn the fuel setting screw outward. Turn the fuel setting screw inward or turn the fuel setting screw outward until the correct reading is
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
311B, 312B, 312B L, 313B, 315B, 315B FM L, 315B L, 317B LN, 318B, 320B, 320B FM LL, 320B L, 320B U, 321B, 322B, 322B L, 322B LN, 325B, 325B L, 330B, 330B L, M325B, OEMS, W330B
307B, 307C, 308C, 311B, 311C, 311D LRR, 311F LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E...
16G, 16H NA, 245, 245B, 307, 311, 3116, 312, 3126, 3126B, 3126E, 312D, 312D L, 314D CR, 314D LCR, 315, 317, 3176, 3176B, 3176C, 318D L, 3196, 320 L, 3208, 320D, 320D FM, 320D L, 320D LRR, 320D RR, 320...
1090, 1190, 1190T, 120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 1290T, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 130G, 135H, 135H NA, 1390, 140B, 140G, 140H, 140H ES, 1...
1090, 1190, 1190T, 120, 120B, 120G, 120H, 120H ES, 120H NA, 1290T, 12F, 12G, 12H, 12H NA, 130G, 135H, 135H NA, 1390, 140, 140B, 140G, 140H, 140H NA, 143H, 14E, 14H, 16, 160H, 163H, 16G, 16H NA, 16M, 2...
1090, 1190, 1190T, 120K, 120K 2, 120M, 120M 2, 1290T, 12K, 12M, 12M 2, 12M 3, 12M 3 AWD, 1390, 140K, 140K 2, 140M, 140M 2, 140M 3, 140M 3 AWD, 14M, 160K, 160M, 160M 2, 160M 3, 160M 3 AWD, 16M, 214B, 2...
120G, 12G, 130G, 140G, 14G, 229D, 3114, 3116, 3208, 3304, 561D, 627B, 637D, 933C, 939, 939C, 941, 951B, 955K, 955L, 963, 973, 977K, 977L, CB-434D, CB-534D, CB-564D, CD-54, CP-433E, CP-533E, CP-573E, C...
1090, 1190, 1190T, 1290T, 1390, 205B, 211B, 215, 215B, 225, 227, 229, 2290, 231D, 235, 235C, 235D, 2390, 2391, 245, 2491, 2590, 307, 307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 C...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 307, 307B, 307C, 308C, 311B, 311C, 312, 312B, 312B L, 312C L, 312D, 313B, 315, 315B, 315B FM L, 315B L, 315C, 315D L, 317B LN, 318B, 318C, 319C, 319D,...
311, 312, 315, 317, 320, 320 L, 320N, 322, 322 FM L, 322 LN, 325, 325 L, 330, 330 FM L, 330 L, 350, 375, 375 L, 5080
305.5, 306, 306E, 307B, 307C, 307D, 308C, 308D, 311, 311B, 311C, 311D LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 313B, 314C, 314D CR, 314D LCR, 315, 315B, 315B L, 315C, 315D L, 317B LN, 318B, 318C...
315, 315B, 315C, 317B LN, 318B, 933, 933C, 939, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
1057499
VALVE
307
307
0874661
VALVE
307, 307B, 320 L, 325, 325 L, 325 LN, 330 FM L, E200B, E70B
307, 307B, 320 L, 325, 325 L, 325 LN, 330 FM L, E200B, E70B
9X8418
VALVE-BALL
235C, 235D, 797F
235C, 235D, 797F
5P4485
VALVE AS-NEEDLE
235C, 235D, 627B, 637D, 814B, 815B, 816B, 941, 951B, 955K, 955L, D4D, D4E, D4E SR
235C, 235D, 627B, 637D, 814B, 815B, 816B, 941, 951B, 955K, 955L, D4D, D4E, D4E SR
1061051
VALVE AS
224
224
5W2588
VALVE AS-FUEL
205, 206, 212, 213B, 214B, 224B
205, 206, 212, 213B, 214B, 224B
8U1093
VALVE GP-ETHER START
213B, 214B, 224B
213B, 214B, 224B
8U3869
VALVE GP
205B, 206B, 211B, 212B, 224B
205B, 206B, 211B, 212B, 224B
1140609
VALVE AS
307
307
1195824
VALVE
307
307
1120022
VALVE GP
307
307