1074393 VALVE AS Caterpillar parts
16M, 24M, 5130, 5130B, 5230, 5230B, 583T, 587T, 773F, 775F, 777F, 777G, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 797B, 797F, 824G, 824G II, 824H, 825G, 825G II, 8...
Rating:
Alternative (cross code) number:
CA1074393
107-4393
1074393
CA1074393
107-4393
1074393
Weight: 0.04 pounds 0 kg.
ARTICULATED TRUCK, WHEEL LOADER,
Compatible equipment models: 1074393:
EJECTOR TRUCK
TRACK-TYPE TRACTOR
D10R
D10T
D11R
D11T
D3G
D3K XL
D4C III
D4G
D4K XL
D5C III
D5G
D5K LGP
D5M
D5N
D5R LGP
D6G2 LGP
D6G2 XL
D6K
D6K LGP
D6K XL
D6N
D6R
D6R II
D6R III
D6T
D6T LGP
D6T XL
D7G2
D7H
D7R II
D8R
D8R II
D8T
D9R
D9T
Number on catalog scheme:
For full view, you need register
Information:
Conditions Which Generate This Code:
Illustration 1 g01362246
Connections of the inching pedal switchThis diagnostic code is associated with the inching pedal switch. The switch is connected to two inputs of the ECM. The inputs are "Normally Open" and "Normally Closed". One of the inputs is open and the other input is grounded during proper operation.The FMI 2 means that the ECM has determined that the "Normally Open" and "Normally Closed" circuits are in the same state.Note: The following test procedure may create other diagnostic codes. Ignore these diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of SPN 702 FMI 2 is active before performing this procedure.Test Step 1. CHECK THE OPERATION OF THE SWITCH
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector or the wires from the switch.
Connect one lead from the multimeter to the common contact (COM) for the switch.
Connect the other lead from the multimeter to the normally open contact (NO) for the switch.
Measure the resistance between contact COM and contact NO. Note the resistance.
Disconnect the lead from contact NO and connect the lead to the normally closed contact (NC).
Measure the resistance between contact COM and contact NC. Note the resistance.Expected Result:The resistance from contact COM to contact NO is greater than 5000 ohms, and the resistance from contact COM to contact NC is less than 5 ohms.Results:
YES - The resistance from contact COM to contact NO is greater than 5000 ohms, and the resistance from contact COM to contact NC is less than 5 ohms. Proceed to Test Step 2.
NO - The resistance measurements do not differ. The switch has failed.Repair: Replace the switch.STOPTest Step 2. CHECK THE OPERATION OF THE SWITCH
Connect one lead from the multimeter to the common contact (COM) for the switch.
Connect the other lead from the multimeter to the normally open contact (NO) for the switch.
Actuate the switch and measure the resistance between contact COM and contact NO. Note the resistance.
Disconnect the lead from contact NO and connect the lead to the normally closed contact (NC).
Actuate the switch and measure the resistance between contact COM and contact NC. Note the resistance.Expected Result:The resistance from contact COM to contact NO is less than 5 ohms, and the resistance from contact COM to contact NC is greater than 5000 ohms.Results:
YES - The resistance from contact COM to contact NO is less than 5 ohms, and the resistance from contact COM to contact NC is greater than 5000 ohms. Proceed to Test Step 3.
NO - The resistance measurements do not differ. The switch has failed.Repair: Replace the switch.STOPTest Step 3. CHECK THE GROUND CIRCUIT OF THE SWITCH IN THE WIRE HARNESS.
Connect one lead from the multimeter to contact COM (wire J766-PU) of the wire harness connector for the switch.
Connect the other lead from the multimeter to frame ground.
Measure the resistance between contact COM (wire J766-PU) and frame ground.Expected Result:
Illustration 1 g01362246
Connections of the inching pedal switchThis diagnostic code is associated with the inching pedal switch. The switch is connected to two inputs of the ECM. The inputs are "Normally Open" and "Normally Closed". One of the inputs is open and the other input is grounded during proper operation.The FMI 2 means that the ECM has determined that the "Normally Open" and "Normally Closed" circuits are in the same state.Note: The following test procedure may create other diagnostic codes. Ignore these diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of SPN 702 FMI 2 is active before performing this procedure.Test Step 1. CHECK THE OPERATION OF THE SWITCH
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connector or the wires from the switch.
Connect one lead from the multimeter to the common contact (COM) for the switch.
Connect the other lead from the multimeter to the normally open contact (NO) for the switch.
Measure the resistance between contact COM and contact NO. Note the resistance.
Disconnect the lead from contact NO and connect the lead to the normally closed contact (NC).
Measure the resistance between contact COM and contact NC. Note the resistance.Expected Result:The resistance from contact COM to contact NO is greater than 5000 ohms, and the resistance from contact COM to contact NC is less than 5 ohms.Results:
YES - The resistance from contact COM to contact NO is greater than 5000 ohms, and the resistance from contact COM to contact NC is less than 5 ohms. Proceed to Test Step 2.
NO - The resistance measurements do not differ. The switch has failed.Repair: Replace the switch.STOPTest Step 2. CHECK THE OPERATION OF THE SWITCH
Connect one lead from the multimeter to the common contact (COM) for the switch.
Connect the other lead from the multimeter to the normally open contact (NO) for the switch.
Actuate the switch and measure the resistance between contact COM and contact NO. Note the resistance.
Disconnect the lead from contact NO and connect the lead to the normally closed contact (NC).
Actuate the switch and measure the resistance between contact COM and contact NC. Note the resistance.Expected Result:The resistance from contact COM to contact NO is less than 5 ohms, and the resistance from contact COM to contact NC is greater than 5000 ohms.Results:
YES - The resistance from contact COM to contact NO is less than 5 ohms, and the resistance from contact COM to contact NC is greater than 5000 ohms. Proceed to Test Step 3.
NO - The resistance measurements do not differ. The switch has failed.Repair: Replace the switch.STOPTest Step 3. CHECK THE GROUND CIRCUIT OF THE SWITCH IN THE WIRE HARNESS.
Connect one lead from the multimeter to contact COM (wire J766-PU) of the wire harness connector for the switch.
Connect the other lead from the multimeter to frame ground.
Measure the resistance between contact COM (wire J766-PU) and frame ground.Expected Result:
Cat SIS web machinery list:
Parts valve Caterpillar catalog:
120G, 120H, 12G, 12H, 12H NA, 130G, 135H, 140G, 140H, 140H NA, 143H, 14G, 14H, 14H NA, 160G, 160H, 163H, 16G, 16H, 16H NA, 5110B, 518, 5230, 5230B, 528, 621B, 631C, 633C, 639D, 666, 769, 769C, 769D, 7...
824G, 825G, 980G
824G, 824G II, 824H, 824K, 980G, 980G II, 980H, 980K, 980K HLG
785C, 785D, 789C, 789D, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 844, 844H, 854G, 854K, 990 II, 990H, 992C, 992D, 992G, 992K, 993K, 994, 994D, 994F, 994H
834B, 844, 844H, 844K, 980C, 980F, 980F II, 988B, 988F, 988F II, 990, 990 II, 990H, 990K, AD55, AD55B, AD60, R2900G, R3000H, RM-300, RM-350B, RM-500
5130, 5130B, 5230, 5230B, 773D, 776C, 776D, 777B, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 793, 793B, 793C, 793D, 797, 797B, 994, 994D, PR-1000, PR-750B
69D, 769D, 770, 771D, 772, 773D, 773E, 773F, 775D, 775E, 775F, 776C, 777D, 777F, 784B, 784C, 785B, 785C, 785D, 789B, 789C, 789D, 793B, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, ...
768C, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776, 776C, 776D, 777, 777B, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793B, 793C, 793D, 797
768C, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 775B, 775D, 776, 776C, 776D, 777, 777B, 777D, 785C, 789C, 793C
772, 772B, 773, 773B, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775B, 775D, 775E, 775F, 775G, 775G LRC, 775G OEM
769D, 770, 770G, 770G OEM, 771D, 772, 772G, 772G OEM, 773D, 773E, 773F, 773G, 773G LRC, 773G OEM, 775F, 775G, 775G LRC, 775G OEM, 776D, 777D, 777F, 777G
2139001
VALVE
973C
973C
4T0358
VALVE
973, 973C
973, 973C
2470C, 2570C, 2670C, 553C, 563C, 573C, 584, 924H, 924HZ, 928HZ, 938H, 950H, 962H, 966H, 972H, 973C, 980H, AP-600D, AP-655D, BG600D, BG655D, IT38H, IT62H, PM-201, PM-565B, RM-300, RM-350B, RM-500
3G3821
VALVE
955L, 963, 963B, 963C, 973, 973C, 977L, 983B
955L, 963, 963B, 963C, 973, 973C, 977L, 983B
1877658
VALVE AS
973C, 973D
973C, 973D
120M 2, 12M 2, 140M 2, 160M 2, 330D, 589, 824H, 824K, 825K, 826H, 826K, 834G, 834H, 834K, 836H, 836K, 844K, 854K, 973C, 980H, 988H, 988K, 990K, 992K, 993K, D10N, D10R, D10T, D10T2, D6R II, D7R II, D7R...
1398653
VALVE AS-WATER
953C, 963C, 973C
953C, 963C, 973C
953C, 963C, 973C
135H, 135H NA, 143H, 160H ES, 160H NA, 163H NA, 16M, 24M, 5110B, 5130, 5230, 5230B, 583T, 587T, 773F, 775F, 777F, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795F AC, 795F XQ, 797, 7...
1074395
VALVE AS
16M, 24M, 5130, 5230, 583T, 587T, 769C, 769D, 771C, 771D, 773D, 773E, 773F, 775D, 775E, 775F, 777D, 777F, 777G, 784C, 785C, 785D, 789C, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 79...
16M, 24M, 5130, 5230, 583T, 587T, 769C, 769D, 771C, 771D, 773D, 773E, 773F, 775D, 775E, 775F, 777D, 777F, 777G, 784C, 785C, 785D, 789C, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 79...
16M, 24M, 5110B, 583T, 587T, 769D, 771D, 773D, 773E, 773F, 775D, 775E, 775F, 776D, 777D, 777F, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795...