1136721 VALVE GP-CHECK Caterpillar parts
320B, 322B, 322B L, 322B LN, 325B, 325B L, 330B, 330B L
Rating:
Alternative (cross code) number:
CA1136721
113-6721
1136721
CA1136721
113-6721
1136721
Weight: 4 pounds 2 kg.
EXCAVATOR,
Compatible equipment models: 1136721:
Number on catalog scheme:
9
For full view, you need register
Information:
Removal Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7505 Mobile Transmission Jack (Low Lift) 1
Accidental machine starting can cause injury or death to personnel working on the machine.To avoid accidental machine starting, turn the battery disconnect switch to the OFF position and remove the key. If the machine is not equipped with a battery disconnect switch, disconnect the battery cables from the battery and tape the battery clamps.Place a do not operate tag at the battery disconnect switch location to inform personnel that the machine is being worked on.
Note: The weights of bottom guards are between 45 kg (100 lb) and 84 kg (185 lb). Bottom guards may contain 90 kg (200 lb) of rock, dirt, liquids, and debris.
Illustration 2 g00701916
Use Tooling (A) and a suitable block to support the front bottom guard.
Remove nuts (1) and the washers.
Remove bolts (2) and the washers. Lower Tooling (A) and remove the front bottom guard from the machine.
Illustration 3 g00809285
Use Tooling (A) and support the next bottom guard that will be removed.
Illustration 4 g00809287
Remove nuts (4) and the washers that attach bottom guard (3) to both sides of tractor frame (5). Remove pin (6). Lower Tooling (A) and remove bottom guard (3) from the machine.
Repeat Steps 4 and 5, as needed.Installation Procedure
Install the bottom guards in the reverse order of removal.
Tighten nuts (1) and nuts (4) to a torque of 370 50 N m (273 37 lb ft).Lowering Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller 1
Accidental machine starting can cause injury or death to personnel working on the machine.To avoid accidental machine starting, turn the battery disconnect switch to the OFF position and remove the key. If the machine is not equipped with a battery disconnect switch, disconnect the battery cables from the battery and tape the battery clamps.Place a do not operate tag at the battery disconnect switch location to inform personnel that the machine is being worked on.
Note: The weights of bottom guards are between 45 kg (100 lb) and 84 kg (185 lb). Bottom guards may contain 90 kg (200 lb) of rock, dirt, liquids, and debris.
Illustration 5 g00809277
Attach suitable lifting device (1) to one side of the machine, as shown. Attach Tooling (A) to the other side of the machine. Attach suitable lifting device (1) to Tooling (A) and pull tightly under bottom guard (2), as shown.
Illustration 6 g00809278
Remove nuts (3) from both sides that secure bottom guard (2) to machine frame (4) .
Illustration 7 g01205500
Use Tooling (A) to lower the bottom guard to ground level. The bottom guard pivots on pin (5) which was not removed.Raising Procedure
Install the bottom guards in the reverse order of the lowering procedure.
Tighten nuts (3) to a torque of 370 50 N m (273 37 lb ft).
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-7505 Mobile Transmission Jack (Low Lift) 1
Accidental machine starting can cause injury or death to personnel working on the machine.To avoid accidental machine starting, turn the battery disconnect switch to the OFF position and remove the key. If the machine is not equipped with a battery disconnect switch, disconnect the battery cables from the battery and tape the battery clamps.Place a do not operate tag at the battery disconnect switch location to inform personnel that the machine is being worked on.
Note: The weights of bottom guards are between 45 kg (100 lb) and 84 kg (185 lb). Bottom guards may contain 90 kg (200 lb) of rock, dirt, liquids, and debris.
Illustration 2 g00701916
Use Tooling (A) and a suitable block to support the front bottom guard.
Remove nuts (1) and the washers.
Remove bolts (2) and the washers. Lower Tooling (A) and remove the front bottom guard from the machine.
Illustration 3 g00809285
Use Tooling (A) and support the next bottom guard that will be removed.
Illustration 4 g00809287
Remove nuts (4) and the washers that attach bottom guard (3) to both sides of tractor frame (5). Remove pin (6). Lower Tooling (A) and remove bottom guard (3) from the machine.
Repeat Steps 4 and 5, as needed.Installation Procedure
Install the bottom guards in the reverse order of removal.
Tighten nuts (1) and nuts (4) to a torque of 370 50 N m (273 37 lb ft).Lowering Procedure
Table 3
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller 1
Accidental machine starting can cause injury or death to personnel working on the machine.To avoid accidental machine starting, turn the battery disconnect switch to the OFF position and remove the key. If the machine is not equipped with a battery disconnect switch, disconnect the battery cables from the battery and tape the battery clamps.Place a do not operate tag at the battery disconnect switch location to inform personnel that the machine is being worked on.
Note: The weights of bottom guards are between 45 kg (100 lb) and 84 kg (185 lb). Bottom guards may contain 90 kg (200 lb) of rock, dirt, liquids, and debris.
Illustration 5 g00809277
Attach suitable lifting device (1) to one side of the machine, as shown. Attach Tooling (A) to the other side of the machine. Attach suitable lifting device (1) to Tooling (A) and pull tightly under bottom guard (2), as shown.
Illustration 6 g00809278
Remove nuts (3) from both sides that secure bottom guard (2) to machine frame (4) .
Illustration 7 g01205500
Use Tooling (A) to lower the bottom guard to ground level. The bottom guard pivots on pin (5) which was not removed.Raising Procedure
Install the bottom guards in the reverse order of the lowering procedure.
Tighten nuts (3) to a torque of 370 50 N m (273 37 lb ft).
Caterpillar SIS machinery equipment:
Caterpillar SIS
325B L Excavator 2JR00001-UP (MACHINE) POWERED BY 3116 Engine »
113-6721
VALVE GP-CHECK
330B L Excavator 6DR00001-UP (MACHINE) POWERED BY 3306 Engine »
113-6721
VALVE GP-CHECK
325B & 325B LN Excavators 6DN00001-UP (MACHINE) POWERED BY 3116 Engine »
113-6721
VALVE GP-CHECK
322B L Excavator 1YS00001-UP (MACHINE) POWERED BY 3116 Engine »
113-6721
VALVE GP-CHECK
322B L & 322B LN Excavators 1ZS00001-UP (MACHINE) POWERED BY 3116 Engine »
113-6721
VALVE GP-CHECK
325B L & 325B LN Excavators 4DS00001-UP (MACHINE) POWERED BY 3116 Engine »
113-6721
VALVE GP-CHECK
320B & 320B L Excavators 4XW00001-UP (MACHINE) POWERED BY 3066 Engine »
113-6721
VALVE GP-CHECK
320B, 320B L, 320B LN, 320B N & 320B S Excavators 1XS00001-UP (MACHINE) POWERED BY 3116 Engine »
113-6721
VALVE GP-CHECK
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
305.5, 306, 306E, 307B, 307C, 307D, 308C, 308D, 311, 311B, 311C, 311D LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 313B, 314C, 314D CR, 314D LCR, 315, 315B, 315B L, 315C, 315D L, 317B LN, 318B, 318C...
311B, 312B, 312C, 312C L, 315C, 318B, 318C, 319C, 320B, 320C, 320C FM, 320C L, 322C, 325B, 325C, 330C, 330C L, 345B II, 350, 365B, 365B L, 375, 385B
1290T, 1390, 2491, 2590, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D...
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321B, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C L, 320 L, 320B, 320C, 320C FM, 320N
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM RR, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN
311, 311B, 311C, 311D LRR, 312, 312B, 312C, 312C L, 312D, 312D L, 313D, 314C, 314D CR, 314D LCR, 315D L, 318C, 318D L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 3...
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B U, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 323D L, 323D LN, E110, E110B, E120B, E200B, E450
318C, 319C, 320, 320 L, 320B, 320B FM LL, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320N, 321C, 321D LCR, 323D L, 323D LN, 323D SA
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, ...
6E6389
VALVE GP
330, 330 FM L, 330 L
330, 330 FM L, 330 L
6E4199
VALVE GP-BANK
IT12B
IT12B
2303228
VALVE GP-COMBINATION
824G II, 824H
824G II, 824H
1041778
VALVE GP-BRAKE CONTROL
CB-434B, CB-434C
CB-434B, CB-434C
6R3472
VALVE GP-VIBRATORY
AP-200B
AP-200B
3725318
VALVE GP-LUBE DISTRIBUTION
950K, 962K
950K, 962K
2596903
VALVE GP-CONTROL
14M, 16M
14M, 16M