1449099 VALVE GP-PRESS Caterpillar parts
621F, 621G, 627F, 627G, 631G, 633E II, 637G, D8N, D8R
Rating:
Alternative (cross code) number:
CA1449099
144-9099
1449099
CA1449099
144-9099
1449099
Weight: 1 pounds 0 kg.
TRACK-TYPE TRACTOR, WHEEL TRACTOR,
This part in 2 request:
Show.
This information for suppliers only!
2021-05-04
2021-05-04
Compatible equipment models: 1449099:
Number on catalog scheme:
13
For full view, you need register
Information:
Installation Procedure
Identify a location for installation of the bottle. Ensure that the location for installation is protected. Ensure that the location of the bottle is lower than the nozzle.Follow the steps that are listed below in order to install the bottle.
Locate the nozzle in a horizontal position less than 3.0m (10 ft) away from the bottle.
Locate the bottle no lower than 1.5 m (5 ft) from the nozzle.
Inspect the location for the installation and ensure that welding in the location will not damage any of the nearby components.
Illustration 3 g01341843
Typical Location of Installation for the Bottle
Weld the bosses onto the frame in order to mount the bottle.
Install the bottle for the cleaning system.
Mount the nozzle.The following requirements need to be followed for the installation of the nozzle.
Illustration 4 g01341929
For optimal performance install the nozzle within 25 mm (1 inch) of the camera lens.Note: When installing the nozzle ensure that the nozzle is not viewable in the camera image.
The nozzle needs to be angled at 45 degrees from the surface of the lens.
Illustration 5 g01338194
Nozzle
Mount the spray nozzle so that the projection of the spray cuts at the base of the glass.
Install the wiring harness. Route the wiring harness with the existing wiring harnesses.
Illustration 6 g01341873
Typical Installation of the Wiring Harness
Install the power wire to the pump. Install the ground wire to the pump. Refer to Illustration 9 for a system schematic.
Locate an suitable ground and Install the other end of the ground wire to the frame.
Locate a location for installation in the cab of the machine for the washer switch.
Illustration 7 g01341911
Typical Installation of the Washer Switch
Connect the cleaning system to an appropriately fused 24 volt power source.
Illustration 8 g01338195
Check Valve
Route the fluid line from the pump to the nozzle. Cut the fluid line and install the check valve no more than 304 mm (1 ft) away from the tank. Ensure that the arrow on the check valve is pointed away from the pump.Note: You must prime the pump before installing the check valve. In order to prime the pump allow the water to flow out of the line in order to purge the air out of the line.
Check the operation of the system.Wiring Schematic
Illustration 9 g01341969
System Connections
Identify a location for installation of the bottle. Ensure that the location for installation is protected. Ensure that the location of the bottle is lower than the nozzle.Follow the steps that are listed below in order to install the bottle.
Locate the nozzle in a horizontal position less than 3.0m (10 ft) away from the bottle.
Locate the bottle no lower than 1.5 m (5 ft) from the nozzle.
Inspect the location for the installation and ensure that welding in the location will not damage any of the nearby components.
Illustration 3 g01341843
Typical Location of Installation for the Bottle
Weld the bosses onto the frame in order to mount the bottle.
Install the bottle for the cleaning system.
Mount the nozzle.The following requirements need to be followed for the installation of the nozzle.
Illustration 4 g01341929
For optimal performance install the nozzle within 25 mm (1 inch) of the camera lens.Note: When installing the nozzle ensure that the nozzle is not viewable in the camera image.
The nozzle needs to be angled at 45 degrees from the surface of the lens.
Illustration 5 g01338194
Nozzle
Mount the spray nozzle so that the projection of the spray cuts at the base of the glass.
Install the wiring harness. Route the wiring harness with the existing wiring harnesses.
Illustration 6 g01341873
Typical Installation of the Wiring Harness
Install the power wire to the pump. Install the ground wire to the pump. Refer to Illustration 9 for a system schematic.
Locate an suitable ground and Install the other end of the ground wire to the frame.
Locate a location for installation in the cab of the machine for the washer switch.
Illustration 7 g01341911
Typical Installation of the Washer Switch
Connect the cleaning system to an appropriately fused 24 volt power source.
Illustration 8 g01338195
Check Valve
Route the fluid line from the pump to the nozzle. Cut the fluid line and install the check valve no more than 304 mm (1 ft) away from the tank. Ensure that the arrow on the check valve is pointed away from the pump.Note: You must prime the pump before installing the check valve. In order to prime the pump allow the water to flow out of the line in order to purge the air out of the line.
Check the operation of the system.Wiring Schematic
Illustration 9 g01341969
System Connections
Caterpillar parts catalog:
Parts valve Caterpillar catalog:
120G, 12E, 12G, 140, 14E, 14G, 16, 163, 172, 173B, 183, 183B, 191, 225, 245, 307, 312, 315, 317, 325B, 330 L, 350, 350 L, 375, 41, 44, 46, 5080, 517, 518, 518C, 527, 528, 528B, 530B, 561C, 561H, 561M,...
517, 527, 561M, 561N, 572R II, 583R, 583T, 587R, 587T, 589, 623G, 933C, 939C, 973D, D10R, D10T, D10T2, D11R, D11T, D3C III, D3G, D3K XL, D3K2 LGP, D4C III, D4G, D4K XL, D4K2 XL, D5C III, D5G, D5HTSK I...
16M, 24M, 5110B, 583T, 587T, 769D, 771D, 773D, 773E, 773F, 775D, 775E, 775F, 776D, 777D, 777F, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793C, 793D, 793F, 793F AC, 793F CMD, 793F OEM, 793F-XQ, 795...
120M 2, 12M 2, 140M 2, 160M 2, 330D, 589, 824H, 824K, 825K, 826H, 826K, 834G, 834H, 834K, 836H, 836K, 844K, 854K, 973C, 980H, 988H, 988K, 990K, 992K, 993K, D10N, D10R, D10T, D10T2, D6R II, D7R II, D7R...
572G, 572R, 572R II, 578, 583R, 587R, 587T, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7F, D7G, D7H, D7R, D7R II, D7R XR, D8H, D8K, D8N, D8R, D9G, PL87
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 12G, 12H, 12H ES, 12H NA, 12K, 12M, 130G, 135H, 135H NA, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 143H, 14G, 14H, 14H NA, 14M, 160G, 160H, 16...
528, 611, 613C, 613C II, 615, 615C, 621B, 621E, 621F, 623E, 623F, 627E, 627F, 631E, 633E II, 637E, 639D, 651E, 657E, 815B, 826C, 916, 926, 936, 950B, 950F, 950F II, 960F, 966D, 966F, 966F II, 970F, 98...
16, 611, 613, 613B, 613C, 613C II, 613G, 615, 615C, 621, 621B, 621F, 621R, 623, 623B, 623E, 623F, 627B, 627E, 627F, 631C, 631E, 631G, 633, 633C, 633D, 633E, 633E II, 637D, 637E, 637G, 639D, 641, 641B,...
120G, 120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 12M 3, 130G, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 140M 3, 160H, 160K, 160M...
611, 615C, 621E, 621F, 623E, 623F, 627E, 627F, 631E, 633E II, 637E, 651E, 657E, 69D, 769C, 769D, 771C, 771D, 773B, 773D, 775B, 775D, 776C, 776D, 777D, 785C, 785D, 789D, 793B, 793C, 793D, 797B, 994, 99...
16G, 16H NA, 611, 615C, 621E, 621F, 621G, 623E, 623F, 623G, 627E, 627F, 627G, 631E, 631G, 633E, 637E, 637G, 651E, 657E, 657G, 769D, 771D, 773D, 775D, 776C, 777D
621F, 623E, 623F, 627F, 769C, 771C, 772B, 773B, 775B, 777, 777B, 785, 994
8M5706
VALVE
16, 561B, 824, 955H, 955K, 977H, 977K, 980, 988
16, 561B, 824, 955H, 955K, 977H, 977K, 980, 988
4K2038
VALVE ASSEM.
955H
955H
4H8156
VALVE
955H, D9E
955H, D9E
9T6105
VALVE GP
D8N
D8N
9T6107
VALVE GP
D8N
D8N
2J7244
VALVE
172, 183
172, 183
183, 184
8H0387
VALVE
D8H
D8H
3J8373
VALVE ASSEM.
118, 129
118, 129
2S2351
VALVE
12E, 16, 561B, 621, 651, 657, 769, 824, 824B, 834, 955H, 977H, 980, 988, D8H, D9G
12E, 16, 561B, 621, 651, 657, 769, 824, 824B, 834, 955H, 977H, 980, 988, D8H, D9G
561B, D4D
350, 350 L, 5130, 5130B, 5230, 773D, 775D, 814F, 814F II, 815F, 815F II, 816F, 816F II, 844, 844H, 950B, 950F, 950F II, 960F, 966D, 966F, 966F II, 966G, 970F, 980C, 980F, 980F II, 988F, 988F II, 990, ...